Noblelift SPM1516 User manual

SPM15-SMS-001_EN
Operating Instructions
SPM1516, SPM1525, SPM1530, SPM1529A
WARNING
Do not use the stacker before
reading and understanding
this operating instructions.
NOTE!
Keep for future reference.

1
Welcome to use our electric stacker. Your stacker is made of high quality steel and SPED mast and
was designed to give a durable, reliable and easy to use product. For your safety and correct
operation, please carefully read this instruction book and warnings on the stacker before using it.
This Operation Instruction of the stacker is edited for you to completely acquire and master the safety
operation of the stacker.
Specifications of different types of the stackers are described in this Operation Instruction. During
operation and maintenance, please apply the relevant parts for the type of the stacker.
All of the information reported herein is based on data available at the moment of printing.
We reserves the right to modify our own products at any moment without notice and incurring
in any sanction. So, it is suggested to always verify possible updates.
1 Technical Specifications

2
Technical Data
Characteristics
1.2 Model of manufacture SPM1516 SPM1525 SPM1530 SPM1529A
1.3 Drive:
(electric-battery or mains,diesel,petrol,fuel gas,manual) manual manual manual manual
1.4 Type of operation
(hand,pedestrian,standing,seated,order picker) pedestrian pedestrian pedestrian pedestrian
1.5 Load capacity / rated load Q (kg) 1500 1500 1500 1500
1.6 Load centre distance c (mm) 600 600 600 600
1.9 Wheelbase y (mm) 1160 1160 1160 1160
Weight
2.1 Weight (including battery) kg 436 516 543 554
Wheels Chassis
3.1 Types (solid rubber,superelastic,nylon, polyurethane) Nylon/PU Nylon/PU Nylon/PU Nylon/PU
3.2 Type size,front mm 180x50 180x50 180x50 180x50
3.3 Type size, rear mm 74x70 74x70 74x70 74x70
3.5 Wheels,number front/rear 2/4 2/4 2/4 2/4
3.6 Track width, front b10 (mm) 658 658 658 658
3.7 Track width, rear b11 (mm) 390/490 390/490 390/490 390/490
Basic Dimensions
4.2 Lowered mast height h1 (mm) 1980 1780 2030 1980
4.3 Free lift h2 (mm) 1440
4.4 Lift height h3 (mm) 1600 2500 3000 2900
4.5 Extended mast height h4 (mm) 1980 3020 3520 3420
4.9 Height of handle min./max. h14 (mm) 790/1156 790/1156 790/1156 790/1156
4.15 Fork height lowered h13 (mm) 85 85 85 85
4.19 Overall length L1 (mm) 1720/1570 1720/1580 1720/1580 1720/1580
4.20 Length to face of forks L2 (mm) 610/670 610/670 610/670 610/670
4.21 Overall width b1 (mm) 762 762 762 762
4.22 Fork dimensions s/e/L (mm) 60/180/1100
60/150/900
60/180/1100
60/150/900
60/180/1100
60/150/900
60/180/1100
60/150/900
4.25 Width over forks b5 (mm) 570
330~640
570
330~640
570
330~640
570
330~640
4.33 Aisle width for pallets 1000×1200 crossways Ast (mm) 2145 2145 2145 2145
4.34 Aisle width for pallets 800×1200 lengthways Ast (mm) 2175 2175 2175 2175
4.35 Turning radius Wa (mm) 1280 1280 1280 1280
Performance
5.2 Lift speed ,laden/unladen mm/s 65/100 65/100 65/100 72/112
5.3 Lowering speed ,laden/unladen mm/s 85/70 85/70 85/70 96/80
5.11 Parking brake manual manual manual manual
E-Motor
6.2 Lift motor rating at S3 15% kw 1.5 1.5 1.5 1.5
6.4 Battery voltage ,nominal capacity K5 V/Ah 12/150 12/150 12/150 12/150
6.5 Battery weight kg 45 45 45 45

3
Residual Capacity at different lifting height
2 SAFETY GUIDANCE
2.1 Operator should read all warning signs and instructions here and on the stacker before using it.
2.2 Do not operate a stacker unless you are familiar with it and have been trained or authorized to do
so.
2.3 Do not operate a stacker unless you have checked its condition. Give special attention to the chain,
the wheels, the handle, the guide frame, the pilot wheel, the mast, battery, etc.
2.4 Do not use on a slopping ground or on a barbaric or explosive danger environment.
2.5 Do not take up any people on the forks.
2.6 When forks lifting, forbid anyone to stand under the forks or pass through the forks.
2.7 The operator had better take on gloves for labor protecting.
2.8 Do not move the stacker when the goods are lifted to the height more than 300mm.
2.9 When the goods have been transported or lifted, all people should be away from the forks for
600mm.
2.10 The weight of goods should be distributed on the two forks, do not use only one fork. The center
of gravity of goods should be in the center of two forks.
2.11 Do not load over maximum capacity.
2.12 Before using or charging it, check cell liquid, if not enough, full it with distilled water.
2.13 Charging should be in dry and ventilated location, and far away from the fire.
2.14 Keeping the forks in the lowest position if not using.
2.15 At other special condition or place, the operator should be carefully to operate the stacker.
3 MAINTENANCE
3.1 Hydraulic oil
Please check the oil level every six months. The oil can be hydraulic oil: ISO VG32, its viscosity
should be 32cSt at 40oC, total volume is about 4.0lt. use temperature -20oC~50 oC
Replace the hydranlic oil (every 12 months).
3.2 Daily check and maintenance
It is necessary to check the stacker daily. Special attention should be paid to the wheels, the axles,
as thread, rags, etc., it may block the wheels, the fork and the mast, the chain, the battery should be
checked, too. The forks should be unloaded and lowered in the lowest position when the job is over.
Up to h3 mm ACTUAL CAPACITY ( Q ) kg
1500 1500
2500 1500
3000 800
Load centre distance ( C )
mm 600

4
3.3 Lubrication
Use motor oil or grease to lubricate all movable parts.
3.4 Maintenance of battery: Keep all the screw caps on each cell battery dry and clean. Each
connecting terminal and cable terminal should be tightened and painted with clean grease. The
exposed connecting terminal and connecting rod of battery should be covered with anti-slip
insulated cover.
3.5 Recharge the battery fully and carry out usual battery maintenance.
Maintenance charge the battery every third month and check the fluid level.
4 HOW TO CHARGE STORAGE BATTERY
4.1 Charge storage battery when its voltage is less than 10 Volt.
4.2 Please check the battery liquid before charging, if it is not enough, add some distilled water.
4.3 The charging environment should be ventilated and far away from the fire.
4.4 If the stacker not use for long time, charge it for not less than two hours every week.
4.5 The voltage on the indicator should not be over 15 Volt when charging.
4.6 Do not use the stacker when charging.
5 CONTROL PANEL
5.1 Urgent button
When you press down this switch, it will switch off the power, and then you turn it clockwise, it will
switch on the power.
5.2 Battery indicator
It indicates the voltage of battery. When its voltage is less than 10 Volt, you should not use this stacker,
you must charge it.
5.3 Control stick
This stick controls the forks to lower or lift.
5.4 Charger socket

5
6 TROUBLES SHOOTING
△
,!DO NOT ATTEMP TO REPAIR THE STACKER UNLESS YOU ARE TRAINED AND
AUTHORIZED TO DO SO.
No
Trouble Clause Fixing Methods
1
The forks can not be
up the max. height. -The hydraulic oil is not enough. -Pour in the oil.
2
The forks can not be
lifted up.(Motor is
rotary)
-Without hydraulic oil.
-The oil has impurities.
-Fill in the oil.
-Change the oil.
3
The motor cannot
run.
-The urgent switch is pressed down,
cut off the power.
-The voltage is too lower.
-The connectors of electrical wire is
loose.
-The contactor of DC motor is bad.
-Turn it clockwise, switch on the
power
-Charge it.
-Turn it firm.
-Replace with new one.
4 The forks cannot be
descended.
-The piston rod or mast is deformed
resulting from partial loading slanting
to one side or over-loading.
-The fork was kept in the high position
for long time with piston rod bared to
arise in rusting and jamming of the
rod.
-The release valve of pump is not
opened.
- Replace with new one.
-Keeping the fork in the lowest
position if not using, and pay
more attention to lubricate the
rod.
-Check it, if damaged, replace
with new one.
5 Leaks
-Sealing parts worn or damaged.
-Some part cracked or worn into
small.
-Replace with the new one.
-Replace with the new one.
6
The fork descends
without the release
valve worked.
-The impurities in the oil cause the
release valve to be unable to close
tight.
-Sealing parts worn or damaged.
-The release valve is damaged.
-Replace with new oil.
-Replace with the new one.
-Replace with the new one.
7 Battery cannot be
charged
-Battery is bad.
-The charging plug is loose.
- Replace with the new one.
- Turn it firm.

6
7 Hydraulic Flow Diagram
8 Electric Wires Diagram
8.1 CIRCUIT DIAGRAM

7
8.2 CONNECTION DIAGRAM