Nobles Trooper 1500H 608570 Product manual

R
Operator and Parts Manual
Carpet Extractor with Heat
Troopert1500H
Model No.:
608570
608571 - Pac
NOBLES CUSTOMER SERVICE:
1--800--365--6625
FAX: [phone]
TECHNICAL SUPPORT:
1--800--522--7839 EXT. 5356
TENNANT COMPANY
701 NORTH LILAC DRIVE
MINNEAPOLIS, MN 55422
MAILING ADDRESS:
TENNANT COMPANY
P.O. BOX 1452
MINNEAPOLIS, MN 55440--1452
608569
Rev. 01 (03-04)

OPERATION
3
Troopert1500H (03--04)
This manual is furnished with each new model.
It provides necessary operation and maintenance
instructions and an illustrated parts list.
Read this manual completely and understand the
machine before operating or servicing it.
Use the illustrated Parts Lists to order parts. Before
ordering parts or supplies, be sure to have your
machine model number and serial number handy.
Parts and supplies may be ordered by phone or mail
from any authorized parts and service center,
distributor or from any of the manufacturer’s
subsidiaries.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
SThe machine is operated with reasonable care.
SThe machine is maintained regularly - per the
machine care instructions provided.
SThe machine is maintained with manufacturer
supplied or equivalent parts.
MACHINE DATA
Please fill out at time of installation for future reference.
Model No.-
Install. Date -
Serial No.-
E1999, 2004 Tennant Company Printed in U.S.A.
Nobles is a registered United States trademark of Tennant Company.
Trooper is a United States trademark of Tennant Company.
TABLE OF CONTENTS
SAFETY PRECAUTIONS 4....................
GROUNDING INSTRUCTIONS 5...........
SAFETY LABEL 5............................
MACHINE COMPONENTS 6...................
MACHINE SETUP 7..........................
OPERATING FLOOR TOOL 8.................
OPERATING HAND TOOL 8...................
DRAINING TANKS 9..........................
DRAINING RECOVERY TANK 9............
DRAINING SOLUTION TANK 9.............
MACHINE MAINTENANCE 9..................
DAILY MAINTENANCE 10...................
WEEKLY MAINTENANCE 10................
MONTHLY MAINTENANCE 10...............
QUARTERLY MAINTENANCE 10............
STORING MACHINE 11........................
RECOMMENDED STOCK ITEMS 11.............
TROUBLE SHOOTING 12......................
SPECIFICATIONS 13..........................
MACHINE DIMENSIONS 13....................
ELECTRICAL DIAGRAMS 14...................
PARTS LIST 15...............................
HANDLE GROUP 15.......................
UPPER HOUSING GROUP 16...............
CHASSIS GROUP 18.......................
PLUMBING GROUP 20.....................
PUMP BREAKDOWN 21....................
OPTIONS 22..................................
127mm (5 in.) HAND TOOL GROUP 22.......
76mm (3 in.) CREVICE TOOL GROUP 22.....
UPHOLSTERY TOOL GROUP 23............
330mm (13 in.) LOW PRESSURE
FLOOR TOOL 24...........................
406mm (16 in.) LOW PRESSURE
FLOOR TOOL 26...........................
SOLUTION AND VACUUM HOSES
GROUP 28................................

OPERATION
4Troopert1500H (03--04)
SAFETY PRECAUTIONS
This machine is intended for commercial use. It is
designed to clean carpet and upholstery in an
indoor environment and is not constructed for any
other use. Use only recommended accessory
tools and commercially available carpet cleaners
intended for machine application.
All operators must read, understand and practice
the following safety precautions.
The following warning alert symbol and the “FOR
SAFETY” heading are used throughout this manual as
indicated in their description:
WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
Failure to follow these warnings may result in:
personal injury, electrocution, electrical shock,
fire or explosion.
WARNING: Do Not Use Flammable Liquids Or
Operate Machine In Or Near Flammable Liquids,
Vapors Or Combustible Dusts.
This machine is not equipped with explosion
proof motors. The electric motors will spark upon
start up and during operation which could cause a
flash fire or explosion if machine is used in an
area where flammable vapors/liquids or
combustible dusts are present.
WARNING: Do Not Pick Up Flammable
Materials Or Reactive Metals.
WARNING: Do Not Operate With Damaged
Power Cord. Do Not Modify Plug. Unplug power
Cord Before Servicing Machine.
If the supply cord is damaged or broken, it must
be replaced by the manufacturer or it’s service
agent or a similarly qualified person in order to
avoid a hazard.
WARNING: Do Not Use Outdoors. Do Not
Expose To Rain. Store Indoors.
The following information signals potentially
dangerous conditions to the operator or
equipment:
FOR SAFETY:
1. Do not operate machine:
-- With flammable liquids or near flammable
vapors as an explosion or flash fire may
occur.
-- Unless trained and authorized.
-- Unless operator manual is read and
understood.
-- Unless cord is properly grounded.
-- With damaged cord or plug.
-- If not in proper operating condition.
-- In outdoor areas.
-- In standing water.
-- With the use of additional extension cords.
Only use manufacturer’s extension cord
equipped with machine which has proper
capacity and is grounded.
2. Before operating machine:
-- Make sure all safety devices are in place
and operate properly.
-- Place wet floor signs as needed.
3. When using machine:
-- Do not run machine over cord.
-- Do not pull machine by plug or cord.
-- Do not pull cord around sharp edges or
corners.
-- Do not unplug by pulling on cord.
-- Do not stretch cord.
-- Do not handle plug with wet hands.
-- Keep cord away from heated surfaces.
-- Report machine damage or faulty
operation immediately.
-- Follow mixing and handling instructions
on chemical containers
-- Never allow children to play on or around.
4. Before leaving or servicing machine:
-- Turn off machine.
-- Unplug cord from wall outlet.
5. When servicing machine:
-- Unplug cord from wall outlet.
-- Avoid moving parts. Do not wear loose
jackets, shirts, or sleeves.
-- Use manufacturer supplied or approved
replacement parts.
-- All repairs must be performed by a
qualified service person.
-- Do not modify the machine from its
original design.

OPERATION
5
Troopert1500H (03--04)
6. When transporting machine:
-- Get assistance when lifting machine.
-- Unplug cord from wall outlet.
-- Use tie--down straps to secure machine to
truck or trailer.
GROUNDING INSTRUCTIONS
Machine must be grounded. If it should
malfunction or breakdown, grounding provides a
path of least resistance for electrical current to
reduce the risk of electrical shock. This machine
is equipped with a cord having an
equipment--grounding conductor and grounding
plug. The plug must be plugged into an
appropriate outlet that is properly installed in
accordance with all local codes and ordinances.
Do not remove ground pin; if missing, replace
plug before use.
SAFETY LABEL
The safety label appears on the machine in the
location indicated. Replace label if it becomes
damaged or illegible.
WARNING LABEL --
Located on back side of machine.

OPERATION
6Troopert1500H (03--04)
MACHINE COMPONENTS
6
5
4
3
2
1
14
13
12
10
9
8
11
7
1. Recovery Tank
2. Solution Tank
3. Accessory Tool Vacuum Hose Hookup
4. Latches
5. Accessory Tool Solution Hose Hookup
6. Casters
7. 305mm (12 in.) Stair Climbing Wheels
8. Vacuum ON/OFF Switch
9. Pump ON/OFF Switch
10. Heater ON/OFF Switch
11. Separate Circuit Indicator Light
12. Power Cord -Main
13. Power Cord -Heater
14. Recovery Tank Drain Hose

OPERATION
7
Troopert1500H (03--04)
MACHINE SETUP
1. Carefully check carton for signs of damage. Report
damages at once to carrier. The machine is shipped
fully assembled and is ready for use.
2. Unscrew and remove solution tank lid. Using a hose
or bucket, fill tank with 57L (15 gal) of hot water,
60°C (140°F) maximum (Figure 1).
ATTENTION: Use different buckets to fill and drain
machine to prevent solution system clogs.
FIG. 1
WARNING: Do Not Use Flammable Liquids Or
Operate Machine In Or Near Flammable Liquids,
Vapors Or Combustible Dusts.
3. Add a recommended cleaning solution to the
proper dilution ratio.
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
ATTENTION: If using powdered cleaning
chemicals, mix chemical with water prior to
adding to the tank.
NOTE: If desired, water alone achieves excellent
cleaning results.
4. Replace solution tank lid after filling.
5. Connect two 7.6 m (25 ft.) extension power cords
into machine.
6. Plug each extension cord into separate grounded
circuits. Circuit indicator lamp (green) will light
when cords are on separate circuits (Figure 2).
ATTENTION: When plugging extension cords into
receptacles be certain to use separate circuits.
This will prevent a circuit overload. Do not
activate heater if green indicator does not light.
FOR SAFETY: Do not operate machine unless
cords are properly grounded.
FOR SAFETY: Do not operate machine with the
use of additional extension cords. Only use
manufacturer’s extension cord equipped with
machine which has proper capacity and is
grounded.
FIG. 2
7. Attach vacuum and solution hoses to front of
machine, then to floor or hand tool (Figure 3).
FIG. 3

OPERATION
8Troopert1500H (03--04)
OPERATING FLOOR TOOL
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
NOTE: Vacuum carpet before cleaning.
1. Activate vacuum, pump and heater switches.
NOTE: Be certain that circuit indicator light is on to
verify that two separate circuits are being used.
2. Place floor tool so bottom of glide plate or
stainless steel shoes are parallel to floor. Squeeze
trigger and apply downward pressure on floor tool
head and slowly pull tool backwards using both
hands. Release trigger 150 mm (6 in.) from end of
stroke (Figure 4).
WARNING: Do Not Pick Up Flammable
Materials Or Reactive Metals.
FIG. 4
3. Push floor tool forward over same path with trigger
released when returning for next stroke. Continue
this pull and push method with a slight overlap of
each stroke.
NOTE: For heavily soiled areas, repeat stroke or
change angle of stroke.
4. Check for excessive foam buildup in recovery
tank. Use a recommended foam control solution to
prevent vacuum motor damage.
ATTENTION: Excessive foam buildup will not
activate the float shut-off screen. Vacuum motor
damage may result.
5. When finished cleaning, turn off switches and
drain recovery tank (See DRAINING RECOVERY
TANK).
6. After cleaning, relieve water pressure from
accessory tool before disconnecting hose.
Squeeze trigger for five seconds after turning off
the machine.
OPERATING HAND TOOL
Optional accessory tool is required.
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
NOTE: This machine cleans most synthetic upholstery
very well. Fabrics like Herculon and synthetic velvets
will clean with excellent results. Extraction is not
recommended for most cottons, silks, wools or natural
fiber velvets. Check cleaning instructions sewn in
furniture by manufacturer for further instructions.
Extra caution should be taken with furniture that has
been re-upholstered. Any material under new
upholstery may bleed and discolor new fabric.
NOTE: Vacuum upholstery before cleaning.
1. TEST FABRIC FOR COLORFASTNESS: Pour a
small amount of cleaning solution on a white cloth.
Hold damp portion of cloth against an area of
upholstery which is hidden from view. Hold it there
for 60 seconds. If no color transfers to cloth, it
should be safe to clean. However, always use
your best judgement.
ATTENTION: Be certain the circuit indicator light
is on to verify that two separate circuits are being
used.
2. Activate vacuum, pump and heater switches.
3. Place hand tool on fabric and squeeze trigger
while applying pressure on fabric and slowly pull
tool backwards. Be careful not to over wet
upholstery. Repeat stroke without spray to get
fabric as dry as possible. Overlap cleaning strokes
to avoid streaking (Figure 5).
FIG. 5
WARNING: Do Not Pick Up Flammable
Materials Or Reactive Metals.
ATTENTION: Do not allow water or foam to enter
float shut--off screen in recovery tank.

OPERATION
9
Troopert1500H (03--04)
4. When finished cleaning, turn off switches and
drain recovery tank (See DRAINING RECOVERY
TANK).
5. After cleaning, relieve water pressure from
accessory tool before disconnecting hose.
Squeeze trigger for five seconds after turning off
the machine.
DRAINING TANKS
FOR SAFETY: Before leaving or servicing
machine, unplug power cords from wall outlets.
ATTENTION: Use different buckets to fill and drain
machine to prevent solution system clogs.
DRAINING RECOVERY TANK
NOTE: When solution tank becomes empty, recovery
tank must be drained.
1. Turn switches off and unplug power cords.
2. Remove drain hose from holder, position hose over
floor drain and twist off knob to drain (Figure 6).
FIG. 6
3. Replace knob tightly before cleaning again.
4. After final draining, remove recovery tank lid and
rinse both tank and float shut-off screen
thoroughly to prevent odor buildup (Figure 9).
DRAINING SOLUTION TANK
1 . To drain remaining solution from solution tank,
disconnect solution hose and attach bleeder hose
(bleeder hose supplied with machine) (Figure 7).
ATTENTION: Relieve water pressure from
accessory tool before disconnecting hose.
Squeeze trigger for five seconds after turning off
the main power switch.
2. Activate pump switch. Pump solution into an
empty bucket (Figure 7).
FIG. 7
3. Rinse solution tank with clean water to prevent
odor buildup. Run vacuum motor for 30 seconds
to discharge any moisture. Store extractor with
covers off to promote air circulation.
MACHINE MAINTENANCE
To keep machine in good working condition, simply
follow machine’s daily, weekly and monthly
maintenance procedures.
FOR SAFETY: When servicing machine, unplug
cords from wall outlets.
For ease of servicing, machine tank is hinged to pivot
away from chassis to allow access to inner components.
Make sure tanks are empty before opening. To open
machine for servicing, follow these steps:
a. Unplug machine.
b. Unlatch front two latches.
c. Lift tank upward, away from chassis (Figure 8).
FIG. 8

OPERATION
10 Troopert1500H (03--04)
DAILY MAINTENANCE
(Every 4 Hours of Use)
1. Clean machine with a non-abrasive, nonsolvent
cleaner.
2. Drain and rinse tanks thoroughly.
3. Remove any lint buildup from float shut-off screen
(Figure 9).
FIG. 9
4. Remove and rinse solution tank screen
(Figure 10).
FIG. 10
5. Inspect power cords for damage. Replace if
damaged. Coil cords neatly after each use.
6. Remove any lodged debris from floor tool.
7. Check spray pattern for clogged spray tips.
WEEKLY MAINTENANCE
(Every20HoursofUse)
1. Check floor tool for loose shoes. If loose, tap back
in place with rubber mallet.
2. Inspect vacuum hose for holes and loose cuffs.
MONTHLY MAINTENANCE
(Every80HoursofUse)
1. Inspect cord grips for damage. Replace if
damaged. Neatly coil cords after each use.
2. Inspect tank for cracks.
3. Lubricate casters with a water resistant grease.
4. Remove spray tips from floor and hand tools and
soak in an acetic acid solution.
NOTE: Do not use pins, paper clips, etc., to unplug
spray tips. This will damage spray tips.
5. Flush pump system. Use acetic acid solution to
dissolve normal alkaline chemical buildup. Follow
these steps:
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
a. Premix .5L (16 oz.) of an acetic acid solution
with 7.5L (2 gal) of hot water 60_C (140_F)
and pour into solution tank.
b. Place a bucket under spray tips to catch
spray.
c. Turn on pump switch.
d. Squeeze trigger on tool for 30 seconds.
e. Allow solution to remain in system for up to 6
hours in above freezing temperatures.
f. Later, spray out acetic acid solution into a
drain. Then run 11.4L (3 gal) of clean water
through system to flush out impurities.
QUARTERLY MAINTENANCE
(Every 250 Hours of Use)
Inspect motors for carbon brush wear. Replace
brushes when worn to a length of 10mm (0.38 in.) or
less. Contact an Authorized Service Center for carbon
brush inspection.
ATTENTION: Contact an Authorized Service
Center for machine repairs. Machine repairs
performed by other than an authorized person will
void the warranty.

OPERATION
11
Troopert1500H (03--04)
STORING MACHINE
1. Before storing machine, be certain to flush out
tanks and drain machine of all water.
2. Store machine in a dry area in the upright position.
3. Remove clear lids to promote air circulation.
WARNING: Do Not Use Outdoors. Do Not
Expose To Rain. Store Indoors.
ATTENTION: If storing machine in freezing
temperatures, be sure that machine and solution
system are completely drained and dry.
RECOMMENDED STOCK ITEMS
Refer to Parts List section for recommended stock
items. Stock Items are clearly identified with a bullet
preceding the parts description. See example below:

OPERATION
12 Troopert1500H (03--04)
TROUBLE SHOOTING
PROBLEM CAUSE SOLUTION
Uneven or no spray from tips. Dirty or plugged spray tips. Clean or replace tips.
p
y
p
Improper spray tip size or spray angle. Replace with proper tips. Also check
alignment of spray tips so all tips
spray in a straight line.
Worn spray tips. Replace spray tips.
Pump switch off. Turn the pump switch on.
Solution hose not connected. Make sure solution hose is connected.
Leaking floor tool. Quick coupler on floor tool faulty. Replace quick coupler.
g
Flow control valve leaking. Contact Service Center.
Hose split or fittings loose. Replace hose and tighten fittings.
Solution hose connection not fully
engaged.
Reconnect quick coupler.
Solution pump will not operate. Fuse blown or circuit breaker tripped
in building.
Replace fuse or reset breaker in
building.
Faulty pump switch. Contact Service Center.
Loose wiring to solution pump. Contact Service Center.
Faulty solution pump. Contact Service Center.
Thermal overload activated - motor is
too hot and will automatically shut
down until cool.
Let motor cool and check what caused
overheat.
Poor or no vacuum suction. Fuse blown or circuit breaker tripped
in building.
Replace fuse or reset breaker in
building.
Faulty vacuum switch. Contact Service Center.
Drain hose plug open or loose. Plug drain hose and tighten knob.
Lint is clogging float shut-off screen. Remove recovery cover and clean lint
off screen.
Air is leaking around clear cover lids. Tighten tank lids.
Vacuum hose is loose. Push hose firmly onto recovery tool
and onto front of extractor.
Holes in vacuum hose or hose cuffs
loose on the hose.
Replace hose or thread cuffs securely
onto hose.
Faulty vacuum motor. Contact Service Center.
Faulty vacuum gasket. Replace gasket.
Float shut--off screen activated. Turn off vacuum, empty tank.
Water not heating. Thermostat failed. Contact Service Center.
g
Loose wires to heater. Contact Service Center.
Limit Thermostat breaker tripped. Reset Limit Thermostat.
Limit Thermostat breaker has failed. Contact Service Center.

OPERATION
13
Troopert1500H (03--04)
SPECIFICATIONS
MODEL Troopert1500H
LENGTH 965mm (38 in.)
WIDTH 483mm (19 in.)
HEIGHT 965mm (38 in.)
WEIGHT 61.2 kg (135 lb)
SOLUTION TANK CAPACITY 56.7L (15 gal)
RECOVERY TANK CAPACITY 71.9L (19 gal)
SOLUTION PUMP 1 A, 120V, 6.81L per min. (1.8 gpm)
6.9 bar (100 psi) max.
VACUUM MOTOR 13 A, 1.66 hp.
120V, 1560 watts
HEATER 14A, 120V, 1700 watts, 77_C (170_F) max. temp.
SEALED WATER LIFT 347.9 cm (137 in.)
DECIBEL RATING AT OPERATOR’S EAR,
INDOORS ON CARPET
82dB(A)
MACHINE DIMENSIONS
483mm (19 in.) 965mm (38 in.)
965mm
(38 in.)

ELECTRICAL DIAGRAMS
14 Troopert1500H (03--04)
120V Wiring
ON
OFF
VACUUM HEATER
SOLUTION
PUMP
PUMP
HANDLE CORD 14- 3
HEATER
POWER
CORD
POWER
CORD
CONTROL
LIMIT
INDICATOR
LIGHT
HANDLE CORD 14- 4
VACUUM
MOTOR
BLK RED
BLK
BLK
WHT
GRN
GRN
GRN
WHT
GRN
BLK
GRN
BLK
WHT
BLK
BLK
WHT WHT
RED
GRN
BLK BLK
WHT
RED BLK
BLK
WHT
GRN
GRN
WHT
BLK
BLK
GRN
WHT

PARTS LIST
15
Troopert1500H (03--04)
HANDLE GROUP
8
1
2
3
5
697
10
11
13
12
17
14
15
16
18
19
20
4
REF PART # DESCRIPTION QTY.
1130227 DCORD, 14/3 X 20” YELLOW (120V) 2
2130166 DCORD GRIP, NYLON/BLK W/NUT 2
3611939 HANDLE, GREEN 1
4130691 DLIGHT, INDICATOR -- GREEN 1
5608605 DSWITCH, ROCKER 250VAC, 10A 3
6120189 DECAL, DASH 1
7140900 SCREW, TRS 10--24X0.75 PHL 1
8140519 NUT, #10--24 KEP 3
∇9614121 ASSEMBLY, PLATE W/ LABEL 1
Y10 613284 LABEL, WARNING EXTRACTORS 1
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEMS
REF PART # DESCRIPTION QTY.
11 140197 SCREW, #10--24X0.38 TRSPHL,
SEM
4
12 140825 SCREW, #6X1/2 PANPHL 2
13 611978 BRACKET, DRAIN HOSE HANGER 1
14 140231 SCREW, .38--16X1.50 HXHDCP 4
15 140017 WASHER, 3/8 LOCK 4
16 140028 WASHER, 0.42B 1.00D FLAT 4
17 130694 DCORD, EXT 14/3X25’ YELLOW 2
18 15858.12 SCREW, #10--24X3/4 FLTPHL 1
19 140328 CLAMP, CABLE 3/8 2
20 140552 NUT, #10--24 NYLOCK 1

PARTS LIST
16 Troopert1500H (03--04)
UPPER HOUSING GROUP
3
20
21
22
23
19
18
24
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
25
27
28
29
31
32
33
42
41
40
39
36
35
37
38
34
26
30

PARTS LIST
17
Troopert1500H (03--04)
UPPER HOUSING GROUP
REF PART # DESCRIPTION QTY.
∇100103 COVER, ASSY. CLEAR LID W/
COUNTERSUNK HOLES
1
Y1100109 LID, OUTER RING 1
Y2100105 DLID, CENTER ONLY CLEAR 1
3120190 DECAL, USE BLEEDER HOSE 1
4120907 LABEL, IMPORTANT--ALWAYS... 1
5140900 SCREW, TRS 10--24X0.75 PHL 6
6140000 WASHER, 0.28B FLAT 6
7602783 BLADDER 1
8602448 STANDPIPE W/NIPPLE 1
9180613 DFLOAT, SHUT--OFF (1) BALL 1
10 606088 FITTING, 1--1/2 NIPPLE 1
11 101714 GASKET, WASTE AIR CHAMBER 1
12 210240 NUT, FLANGED 1--1/2 FPT 1
13 100102 DCLEAR LID W/STANDARD HOLE 1
14 120907 LABEL, IMPORTANT--ALWAYS... 1
15 120906 LABEL, IMPORTANT--DRAIN... 1
16 140825 SCREW, #6X1/2 PANPHL 6
∇190965 KIT, DRAIN HOSE COMPLETE 1
Y17 160627 HOSE, DRAIN 1
Y18 140072 CLAMP, HOSE, 1.56D STEPLESS 2
Y19 140921 SLEEVE, HOSE, DRAIN 1
Y∇701061 DPLUG, ASSY, HOSE, DRAIN 1
YY20 230831 KNOB, DRAIN HOSE 1
YY21 230882 STRAP, DRAIN STOPPER 1
YY22 140056 WASHER, 3/8 FENDER 1
YY23 140955 FITTING, PLUG, DRAIN HOSE 1
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEMS
REF PART # DESCRIPTION QTY.
24 614157 CLAMP, HOSE 27MM TO 51MM 1
25 608477 DECAL, TROOPER 1500H 2
26 608555 TANK, RECOVERY, GREEN 1
27 230845 PLATE, CORD CLAMP 1
28 140834 SCREW, .25--20X0.62 FLTPHL 1
29 140258 SCREW, 1/4--20X4--1/4 STUD 3
30 140134 SLEEVE, .376ODX.253IDX.28LG 2
31 230846 BRACKET, TANK SUPPORT 1
32 140000 WASHER, 0.28B FLAT 2
33 140016 WASHER, 0.25 LOCK 2
34 24672 SCREW, .25--20X0.75 HXHDCP 2
35 140259 SCREW, .25--20X0.62 HXHDCP 3
36 140016 WASHER, 0.25 LOCK 3
37 230946 BRACKET, TANK BRACE FRONT 1
38 608186 DECAL, “NOBLES” 1
39 140932 DLATCH, RUBBER, W/ KEEPER 2
40 609980 SCREW, #8--32X0.38 TRSPHL
SEMS
4
41 140713 RIVET, BLIND, .188D X 0.58 1
42 230905 TUBE, INLET 1

PARTS LIST
18 Troopert1500H (03--04)
CHASSIS GROUP
1
3
2
8
9
10
11
12
13
14
15 16
17
24
22
27
28
29 31
32
35
36
37
38
39
40
4
6
7
25
712
11
19
34
41
26
21
42
20
33
18
5
23
30

PARTS LIST
19
Troopert1500H (03--04)
CHASSIS GROUP
REF PART # DESCRIPTION QTY.
1180103 DPUMP, SOLUTION, 100 PSI, 120V 1
2140011 WASHER, 0.21B FLAT 4
3140519 NUT, #10--24 KEP 4
41014262 SCREW, #10--24X1.5 PANPHL 4
5140869 SCREW, #10--24X1.75 PANPHL 2
6069762005 WASHER, #10 LOCK 2
7140011 WASHER, 0.21B FLAT 4
8100118 DGASKET, VAC MOTOR, 5.7 DIA. 1
9130133 TERMINAL, ML .25 RED 2
∇10 130996 DMOTOR,VAC5.7D3--STAGE 1
Y602741 DBRUSH, CARBON 2/PK 1
Y130486 FAN SHELL 1
11 140308 CLAMP, HOSE 1.31 TO 2.25 2
12 160629 DHOSE, 2” X 28” WHITE 1
13 41169 NUT, .25--20 NYLOCK 3
14 102567 DGASKET, VAC MOTOR INTAKE 1
15 230390 HINGE, TANK 1
16 140000 WASHER, 0.28B FLAT 4
17 140885 SCREW, .25--20X.50 TRSPHL 7
18 608566 CHASSIS, GREEN 1
19 140918 SPACER, .20X.31X1.00 2
∇20 180440 DHEATER ASSY, 120V, 1700W
COMPLETE
1
Y102566 INSULATOR, HEATER 1
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEMS
REF PART # DESCRIPTION QTY.
21 140823 SCREW, #10--24X0.62 TRSPHL 2
22 140552 NUT, #10--24 NYLCK 1
23 140328 CLAMP, CABLE 3/8 2
24 140196 SCREW, #10--24X1 TRSPHL 1
25 140932 KEEPER (PART OF LATCH) 2
26 609980 SCREW, #8--32X0.38 TRSPHL
SEMS
4
27 140519 NUT, #10--24 KEP 3
28 140196 SCREW, #10--24X1 TRSPHL 1
29 608906 AXLE, 1/2 DIA X 18.352 1
30 140008 WASHER, 1/2 FLAT 6
31 103009 DWHEEL, 12” X 1.75 WHITE/GRAY 2
32 103019 CAP, HUB, WHEEL 2
33 102568 STRAP, NYLON W/ ADHESIVE 1
34 101288 COVER, HEATER 1
35 230746 BRACKET, AXLE, OFFSET 2
36 140016 WASHER, 0.25 LOCK 4
37 140259 SCREW, .25--20X0.62 HXHDCP 4
38 103065 DCASTER, 4” SWIVEL 2
39 140016 WASHER, 0.25 LOCK 8
40 140259 SCREW, .25--20X0.62 HXHDCP 8
41 140058 WASHER, .543X.875X.062 WAND 1
42 150933 DFITTING, QDC/04PM, SER 60 1

PARTS LIST
20 Troopert1500H (03--04)
PLUMBING GROUP
5
3
8
9
10
2
3
4
14
15
16
18
17
19
26
4
12
3
5
11
12
3
21
11
3
21
24
25
23
22
13
13
3
2
12
20
IN
OUT
1
6
7
REF PART # DESCRIPTION QTY.
1180103 DPUMP, SOLUTION, 100 PSI, 120V 1
2613488 HOSE, GRAY 3/8“ X 24” 1
354333 CLAMP, HOSE, WORM, 0.31--0.88D 6
4150412 FITTING, E90, PM06/BM06 2
5609432 HOSE, GRAY 3/8“ X 16” 1
6180628 DFILTER, SCREEN, 100 MESH 1
7600451 PLATE, BLADDER ASM 1
8140000 WASHER, 0.28B FLAT 4
9140016 WASHER, 0.25 LOCK 4
10 140259 SCREW, .25--20X0.62 HXHDCP 4
11 600545 FITTING, 90 DEG
1/4MPTX.312 TUBE
2
12 150511 FITTING, STR, PF04/BM06 3
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEMS
REF PART # DESCRIPTION QTY.
13 600546 FERRULE S/S FOR #600545 2
14 130692 CONTROL, THERMOSTAT 1
15 140197 SCREW, #10--24X0.38 TRSPHL,
SEM
3
16 101288 COVER, HEATER 1
17 6032.6 SCREW, #8--32X0.38 PANPHL 4
18 130693 LIMIT, THERMOSTAT 1
∇19 180440 DHEATER ASSY, 120V, 1700W
COMPLETE
1
Y102566 INSULATOR, HEATER 1
20 102568 STRAP, NYLON W/ ADHESIVE 1
21 613482 HOSE, GRAY 3/8X5/8X12” 1
22 27048 FITTING, E90, PM04/PF04 1
23 140058 WASHER, .543X.875X.062 WAND 1
24 150615 FITTING, STR, 04PM CLOSE 1
25 150933 DFITTING, QDC/04PM, SER 60 1
26 700141 DHOSE, SOLUTION BLEEDER 1