Noblewell NWCT1B User manual

Lift Top Coffee Table
Instruction Manual

- 1 -
Supplied Parts and Hardware
M6x12mm
G*4
M3.5x14mm
H*22F*8
M3.5x25mm
I*16
M3.5x35mm
J*14
B*1 C*24A*1 D*24 E*6
⑨
⑧
⑩
⑪
⑫
⑥
⑤
③
①
⑦②
②
④
⑦
⑧
⑨
⑨
⑩

- 2 -
1. Screw the cam bolt [C] into the threaded insert on the panel.
2. Connect both panels together making sure cam bolt [C] goes into the
pre-drilled large hole on the end of panel for cam lock [D].
3. Insert the cam lock [D] into the pre-drilled large hole on the panel. Make
sure the cross slot of cam lock [D] faces out.
4. Rotate the cam lock [D] clockwise with a self-supplied phillips screwdriver
to lock the cam bolt [C] in place.
C
D
C C C
Tools Needed (Not lncluded)
CAM LOCK SYSTEM OPERATION
Phillips Screwdriver Rubber Mallet
C
C
D
D

J
- 3 -
③
④
STEP 1
②*1 ③*1 ④*1 C*2 J*4
②
②
J
Phillips
Screwdriver
(Not lncluded)
Note: Keep the grooves on the
panels ② ③ ④ are at the
same level.
J
J
C
C

- 4 -
STEP 2
⑤*1 ⑪*1 J*3
⑪
⑤
J
J
J
Phillips
Screwdriver
(Not lncluded)
Note: Make sure the four big holes
point to the bottom in this step.

D
- 5 -
STEP 3
⑪
⑤
D
D
D
Phillips
Screwdriver
(Not lncluded)
D*2

- 6 -
STEP 4
⑥*1
⑥

- 7 -
STEP 5
②*1 C*2 D*2 J*4
②
J
J
JJ
D
D
D
D
②
CC

- 8 -
STEP 6
⑫*1 J*3
J
J
J
⑫
J
Phillips
Screwdriver
(Not lncluded)
Note: Keep these big holes points
to outwards in this step.
⑪

- 9 -
STEP 7
⑨*2 ⑩*2 C*10 D*6 F*4
⑨
⑩Phillips
Screwdriver
(Not lncluded)
Rubber Mallet
(Not lncluded)
F
D
D
D
F
Make sure these holes
face down in this step.
⑩
CC
C
C
C
⑨
X2 X2
X2 X2

- 10 -
STEP 8
⑦*2 ⑧*2 C*10 D*6 F*4
Phillips
Screwdriver
(Not lncluded)
Rubber Mallet
(Not lncluded)
F
D
D
D
F
⑦
⑧
Make sure these holes
face down in this step.
⑦⑧
C
C
CCC
X2 X2
X2 X2

- 11 -
⑩
⑦
⑨
D
D
D
D
⑨
⑩
⑦
⑧⑧
STEP 9
D*8
Phillips
Screwdriver
(Not lncluded)
⑫

- 12 -
I*16
STEP 10
Phillips
Screwdriver
(Not lncluded)
I
I
I
I
I
I
I
I
II
II

- 13 -
①*1 E*6 H*6
H
H
H
H
H
H
E
E
E
E
E
E
Phillips
Screwdriver
(Not lncluded)
①
STEP 11
I

- 14 -
A*1 B*1 G*4 H*4
G
G
H
H
G
H
H
H
H
G
G
G
Phillips
Screwdriver
(Not lncluded)
①
Note: Keep the spring points to inwards and the two vertical
frames are close to the front side of the top panel ① in this
step.
STEP 12
Vertical
Frame
Front
①

- 15 -
H*12
H
HH
HH
H
H
HH
HH
H
Phillips
Screwdriver
(Not lncluded)
STEP 13
You may need
assistance with
this step.