noisehush N700 User manual

1. Notice Before Using
• Before the initial use, charge the Headset at least 4
HOURS, preferably overnight (8-10 hours).
• If Headset has not been used for more than 21 days,
when recharging it please charge unit at least 4 hours,
preferably overnight (8-10 hours) and the LED Indicator
Light may take several hours to show recharging is
complete.
•While charging the unit, please do not use the Headset.
•When the LED Indicator Light flashes red during usage or
while on standby, the battery is low and you should
recharge the unit as soon as possible.
2. Product Introduction
* Functions (Answering / Ending / On / Off ) Button #3
* LED Indicator Light *Receiver / Speaker *Microphone
* Power Interface / Adapter for Charging the Unit
* Ear Hook * Decrease Volume Key (-) 1
* Increase volume key (+) 2
3. Charging the Headset
The N700 comes with a built in Lithium Polymer battery. To
charge the unit, Plug the travel charger into an electrical
outlet or Plug the unit end of the Travel Charger into the
Power Interface Adapter on the Headset. While charging,
the LED Indicator Light will turn red and light will shut off
or flash red when fully charged.
4. Power On / O
a. To TURN THE UNIT ON , PRESS AND HOLD THE Function
button for 5 seconds. The power will turn on after the LED
Indicator Light flashes the blue light 3 times.
b. To turn the unit off, press and hold the Function button
for 5 SECONDS UNTIL THE RED Indicator Light flashes
3times.
5. Pairing the Headset with a Bluetooth Device
Before you use the Headset the first time, you must pair
the unit with a Bluetooth device i.e. cellular phone. To set
up the pairing:
a. Insure your mobile phone is Bluetooth capable
b. Make sure the Headset is turned off.
c. Press and hold the Function button for 10 seconds until
the Indicator Light flashes alternating “Red – Blue – Red –
Blue ” to enter the pairing mode.
d. On your mobile device start the Bluetooth search
function. Refer to the mobile device manufacturer’s
instructions regarding pairing the device to the
NoiseHush-N700 Bluetooth Headset.
Continue on other side
Index
1. Notice Before Using
2. Product Introduction
3. Charging the Headset
4. Power On/O
5. Pairing the Headset with a Bluetooth Device
6. Answering Calls
7. Refusing Calls
8. Voice Dialing
9. Redialing
10. Mute
11. Transferring Calls
12. Adjusting the Volume
e. When your mobile device is in the stage of searching for
a new Bluetooth device, it should locate and pair with the
NoiseHush-N700.
f. On your mobile device, please choose and confirm the
NoiseHush-N700 as your Bluetooth paired device.
g. Key in the Headset Passcode-“0000” and press “YES”. If
the pairing is successful, the Indicator light on the Headset
will flash the blue light only. For some mobile phones,
after pairing you may have to select and reconfirm
NoiseHush-N700 PAIRING EACH TIME YOU TURN ON THE
PHONE. Please read you phone manufacturer’s
instructions regarding Bluetooth devices.
h. The Headset should now be in standby mode – ready to
send and receive calls.
6. Answering Calls
a. While answering calls, the blue Indicator light flashes 4
times each second.
b. If the mobile device is ringing and your Headset is off,
turn the Headset on first, then press the Function button
to answer the call.
c. If your mobile device has “automatic answer” feature and
it already set up to answer using this function, Headset
can receive the call automatically without pressing the
button.
d. When the call is complete, press the Function button to
end the call.
7. Refusing Calls
To refuse a call, wait to hear from our receiver, then press
and hold the Function button 2-3 seconds until you hear
the “Du” sound to refuse the call. If you have the mobile
device set to automatically answer calls, refusing call as
described here will not apply.
8. Voice Dialing
a. If your mobile phone supports Voice Dialing, you can
use this Function with your Headset also.
b. Under the standby or connecting mode, press the
Function button on the Headset and follow the mobile
devices’ manufacturer’s instructions to proceed with Voice
Dialing.
9. Redialing
a. If your mobile device supports the Redialing feature,
you can also use this function with your Headset.
b. Under the Standby or Connecting mode, press the
Decrease Volume Key(-) of the Headset for 2-3 seconds
until you hear the “Du” sound to redial the last call.
10. Mute
a. During a phone conversation, press the Decrease
Volume Key (-) and Increase Volume Key (+) at the same
time until you hear the “Du” sound to begin the Mute
function of the Headset.
b. While in Mute mode, you will hear an intermittent “Du”
sound
c. To cancel the Mute mode, press either Decrease Volume
Key (-) or the Increase Volume Key (+) to end this function.
11. Transferring Calls
a. Transfer a call from the headset to the mobile device.
While a call is in progress, press the Increase Volume Key
(+) for 2-3 seconds until you hear one “Du” sound.
b. Transfer a call from the mobile device to the headset.
While a call is in progress, press the Increase Volume
Key(+)for 2-3 seconds until you hear one “Du” sound. Note
that some phones may require a 2-3 seconds press of the
Function button instead of the Increase Volume Key (+) to
perform this function.
12. Adjusting the Volume
a. To increase the volume, press the Increase Volume Key (+).
To decrease the volume, press the Decrease Volume Key (-).
The NoiseHush N700 is using Bluetooth wireless
technology and is capable of connecting with Bluetooth
devices designed with Audio Gateway and PDAs. Desktop
and notebook computers can be connected and paired
with the Headset using a USB Bluetooth Dongle.
Contact Us
For additional help or to purchase accessories such as
AC/DC, please visit us at www.noisehush.com