noken SQUARE 100141901 User manual

Carretera CV-20 km.2 · 12540 Vila-real · Castellón · Spain
Tel: [phone] - Fax: [phone]
e-mail: [email protected] · www.noken.com
SQUARE
100141901_N183050314
Rain and cascade shower head

2
Description
1 100267608_N240550124
2100223164_N240550106
3100223183_N240550105
4100223201_N240550107
- Please read these instructions carefully before starting installation and retain it for future reference.
Please leave this instructions with the end user.
- Remove all packaging and check the product for missing parts and damages before starting the
installation.
- Any alterations made to this product and its fittings may infringe the water regulations and will
invalidate the guarantee.
- We strongly recommend the use of a qualified and registered plumber.
- In new buildings it is recommended to water fill the traps to ensure toxic gases do not corrode the
surface of the taps. It is recommended that the room is well ventilated.
- Thoroughly flush through all pipe work prior to the installation of terminal appliances, e.g. Shower
heads, taps, inlet valves, etc.
- Periodic cleaning and maintenance should be use to avoid the build up of damaging limestone
deposits.
- Bathroom beauty products such as liquid soap, shampoo or shower gels may damage some
materials.
1
2
3
4

3

4
25
8"
97
16"
12
5
7
8 "
34
Drill four holes on the wall
Ø5/16” x 1_3/16”
Insert four plastic spansile
screws.
Fix plate and concealed body
with screws.
Use screws to fix plate to the
wall.

5
Drill two holes with
diameter of 1_3/16” on
the ceramic tiles.
57 8"
56
Make sure the concealed pipes
are at the same level with
ceramic tile,at least not
exceeding the ceramic tile.
23
8"
Screw water supply
concealed pipes in the wall.
connector into the
78
Connect the inlet hoses to the
concealed body. Both inlets must
be water supplied independently,
not combined.

6
910
11
Aim the shower head at watersupply connector
Screw the nut until the shower head is fixed.

7
12
13
Connect the flexible hoses in the watersupply connector
Install the cover with the screws

8
Working pressure 7,3 - 72,5 PSI
Optimal pressure 43,5 PSI
Maximum pressure 72,5 PSI
Max. temperature 140ºF
Material Stainless steel
*We recommend the installation of the pressure valves where the high pressure is present
14

9
Pressure
(PSI)
FLOW
RATE (gpm)
0,00 0,00
7,25 1,50
14,50 2,10
29,01 2,45
43,51 2,50
58,01 2,50
72,52 2,50
0,0
0,5
1,0
1,5
2,0
2,5
3,0
0 10 20 30 40 50 60 70 80
FLOW RATE (gpm)
PRESSURE (PSI)
Pressure
(PSI)
FLOW
RATE (gpm)
0,00 0,00
7,25 1,00
14,50 1,75
29,01 2,40
43,51 2,50
58,01 2,50
72,52 2,50
0,0
0,5
1,0
1,5
2,0
2,5
3,0
0 10 20 30 40 50 60 70 80
FLOW RATE (gpm)
PRESSURE (PSI)
WATERFALL
RAIN

10
BRASSWARE AND ACCESSORIES
First of all we thank you for buying our products which are manufactured to the highest standards.
However in common with other products our brassware requires the correct cleaning and periodic
maintenance.
BRASSWARE SURFACES
As stated in the norm DIN EN 248 the materials used to plate brassware are Chrome, Nickel, stainless
steel, brass and others to leave a superior, easy to clean, pleasing finish. Before cleaning please
check the material used and only use a suitable cleaner.
CLEANING
To clean brassware and accessories please note the following recommendations.
- For regular cleaning only use warm soapy water, if this is not possible use soft non abrasive gels or
similar cleaning products, rinse thoroughly and polish with a soft cloth.
- Please avoid the use of harsh or abrasive products such as scouring powders, those products with
phosphoric acid, hydrochloric acid, formic acid or acetic acid that could badly damage the product.
Please only use PH neutral products.
- Dry the items after each cleaning sesion and after every use to avoid limestone appearance.
WARNING
- Cleaning materials will only worsen already damage product.
- Do not mix cleaning products, the chemical reactions can emit toxic fumes and react badly with
product surfaces.
- Do not use harsh or abrasive cloths, pads or cleaning products.
- Do not use bleach or other chlorine based cleaning products.
- Only use suitable cleaning products as recommended for each product he cleaning products only
make worse the surfaces if those are already damages.
RECOMENDATIONS FOR THE CLEANING AND PRESERVATION OF BRASSWARE AND
ACCESSORIES
- Read the manufacturers instructions.
- To protect the brassware, internal mechanism and to extend the life of the product it is recommended
in line with “best practice“ to install isolation valves and in line filters.
- Regular cleaning to reduce lime scale and soap residue build up.
- Do not leave these products in contact with the product surface longer than the manufacturer’s
recommendations and rinse thoroughly with clean water.
- Do not spray cleaning products directly onto the product surface, spray onto a soft cloth and then
apply to the product. Spraying directly onto the product can lead to cleaning fluids being drawn into
the products through capillary action causing irreversible damage.
- If a tap is left dripping it may lead to staining and lime scale build up. Please ensure taps are
correctly turned o󰀨 after use.
GUARANTEE CLAUSE
- Failure to comply with the maintenance instructions may invalidate the guarantee.