NOMA Canvas CTI1513937 User manual

2. Hook the head (F) on the body (E), then secure the head (F) to the body (E) with a plastic tie (L). Insert
3. Insert the ears (J, K) into the head (F). Insert the antlers (H, I) into the head (F). (Fig. 3)
Fig. 2
Fig. 4
tail (G) into the body (E). (Fig. 2)
1. Insert the four legs (A, B, C, D) into the body (E) as shown in the magnified drawing. Then connect the front
legs (A, B) and the back legs (C, D) with hooks separately fixed on legs B and D. (Fig. 1)
Fig. 1
Fig. 3
4' IRIDESCENT WINTER DEER
For indoor and outdoor use
Retain carton for storage purposes
Instruction Manual
IMPORTANT : Please read this manual carefully before assembly and save it for reference.
Warranty ASSEMBLY INSTRUCTIONS
1-year Limited Warranty
4. Insert ground stakes (M) through four legs into the ground. (Fig. 4)
K
J
L
M
model no. CTI1513937 | www.noma.com
Made in China
Imported by
CTC Triangle (USA) LLC, 14000 24th Street E, Sumner, WA, USA 98390
This CANVAS product carries a one-year warranty against defects in workmanship and materials.
Noma agrees to replace a defective product, within the stated warranty period, when returned to the place
of purchase with proof of purchase. This product is not guaranteed against wear or breakage due to misuse
and/or abuse.

IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
a) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products
are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet.
If one is not provided, contact a qualified electrician for proper installation.
b) This seasonal-use product is not intended for permanent installation or use.
c) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
d) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
e) Do not let lamps rest on the supply cord or on any wire.
f) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
g) ! To avoid risk of fire, burns, personal injury and electric shock, it should
This is an electric product—not a toy
not be played with or placed where small children can reach it.
h) Do not use this product for other than its intended use.
i) Do not hang ornaments or other objects from cord, wire, or light string.
j) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
k) Do not cover the product with cloth, paper or any material not part of the product when in use.
u) Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS - This manual contains important safety and
Use and care instructions
IMPORTANT SAFETY INSTRUCTIONS
m) Do not use an extension cord.
n) Reference the National Electrical Code, ANSI/NFPA 70, specifically for the installation of wiring and
clearances from power and lighting conductors.
o) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction.
p) Do not install or use within 10 feet of a pool.
q) Do not use in a bathroom.
r) WARNING: Risk of Electric Shock. When used outdoors, install only to a covered Class A GFCI
protected receptacle that is weatherproof with the power unit connected to the receptacle. If one is not
provided, contact a qualified electrician for proper installation. Ensure that the power unit and cord do not
interfere with completely closing that receptacle cover.
s) WARNING: Risk of Fire. Installation involves special wiring methods to run wiring through a
building structure. Consult a qualified electrician.
t) WARNING: Not for use with receptacles that are weatherproof only when the receptacle is
covered (attachment plug cap not inserted and receptacle cover closed).
operating instructions for power units.
l) This product is equipped with push-in type lamps. Do not twist lamps.
c) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is placed, including trees, branches,
a) When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live
trees in which the needles are brown or break off easily. Keep the live tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and stable.
or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from sunlight.

Federal Communications Commission (FCC) Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
CAUTION:
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
NOTE:
ADAPTOR MODEL NO. TS-4.5V1A
Replace the lamp
User servicing instructions
CAUTION
1. Risk of fire. This product does not contain lamp shunts, so if one lamp burns out, the lights in that
circuit will not light.
Caution
2. To reduce the risk of fire and electric shock: a) do not install on trees having needles, leaves or branch
coverings of metal or materials which look like metal, and b) do not mount or support strings in a manner
that can cut or damage wire insulation.
packaged with this product or marked for use with this product.
3. To reduce the likelihood of excessive heat and possible damage, use only decorative lamp accessories
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Unlock the burned-out LED lamp by lifting the hook.
4. Replace lamp with only 3.0 V, 0.072 watt push-in type LED lamp (provided with product).
5. Lock the hook of lamp base by pushing lock down into the tab.
3. Pull lamp and plastic base straight out of lampholder.
Always match the hook to the tab.
Caution
To reduce the risk of overheating, replace burned-out lamps promptly. Use 3.0 volt, 0.072 watt
LED lamps only.
CAUTION:
If the lamp base of the replacement lamp does not fit in the string: (as shown below by the Figs.)
a) Remove the base of burned-out lamp by straightening lamp leads and gently pull lamp out.
b) Thread leads of new lamp through holes in old base with one lead in each hole.
c) After lamp is fully inserted into base, bend each lead up, like other lamps in the light set
so that the leads will touch the contacts inside the lampholder (always match the long lead
of new lamp to the hook of lamp base).
Unlock Lock
Hook
Tab