North American Tool 7518 User manual
8807518 7/11
1 TON CHAIN HOIST
CALIFORNIA PROPOSITION 65
WARNING: You can create dust
when you cut, sand, drill or grind
materials such as wood, paint,
metal, concrete, cement, or other
masonry. This dust often
contains chemicals known to
cause cancer, birth defects, or
other reproductive harm. Wear
protective gear.
WARNING: This product or its
power cord may contain
chemicals, including lead,
known to the State of California
to cause cancer and birth
defects or other reproductive
harm. Wash hands after
handling.
Important!
When using equipment, a few
safety precautions must be
observed to avoid injuries and
damage. Please read the complete
operating manual with due care.
Keep this manual in a safe place,
so that the information is available
at all times. If you give the
equipment to any other person,
give them these operating
instructions as well.
We accept no liability for
damage or accidents which
arise due to non-observance of
these instructions and the
safety information herein.
SPECIFICIATIONS
Rated capacity: 1 ton
Distance between hooks:
11 in
Standard Lifting Height:
9 ft. 10 in.
CAUTION:
FOR YOUR OWN SAFETY,
READ INSTRUCTION
MANUAL COMPLETELY AND
CAREFULLY BEFORE
OPERATING THIS CHAIN
HOIST.
Any failures made in
following the safety
regulations and instructions
may result in an electric
shock, fire and/or serious
injury.
INSTRUCTIONS
Do not overload the hoist.
Ensure the chain block,
lubrication of the transmitting
parts and load chain are in
proper condition before using
the hoist.
Before lifting, ensure the
hooks are securely attached.
Ensure the load chain is not
twisted. To lift the load, pull
the hand chain to rotate the
hand wheel in a clockwise
direction. Pull the hand chain
in the opposite direction to
lower the load.
Do not pass or work under a
load while it is being lifted.
While lifting or lowering a
load, pull the hand chain
steadily to prevent jerking or
tangling.
Stop operation immediately if
the chain pull force exceeds
that or a normal operation
such as if there is anything
entangled in the load, if there
is trouble with any parts of the
block, and weather the load
weight is
Model: 7518
feedback@natitools.com
2
over the rated capacity of the
block.
MAINTENANCE
Clean off the dirt on the chain
block, lubricate its parts with
grease after use and store it in
a dry place.
While assembling the brake
mechanism, take care to mesh
the slanting teeth of the ratchet
disc and the pawl.
Make sure that the spring and
pawl work sensitively and
reliably. Turn the hand wheel
clockwise ensuring it presses
the disc and the plates on the
brake seat. If turned clockwise,
there should be clearance
between the disc and the plate.
After cleaning and repairing the
block should be subjected to a
no-load test and load test. A
chain block can be put into
operation after it has been
tested and found under reliable
brake and in good condition.
Keep the friction surfaces of the
brake clean. Break mechanisms
should be inspected regularly
for prevention of faulty breaking
and falling of the load.
feedback@natitools.com
3
North American Tool (NAT) Industries makes every effort to ensure that this product meets high
quality and durability standards. NAT warrants to the original retail consumer a 1-year limited warranty
from the date the product was purchased at retail and each product is free from defects in materials.
Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, or
accidents, repairs or alterations, or a lack of maintenance. NAT shall in no event be liable for death,
injuries to persons or property, or for incidental, special, or consequential damages arising from the
use of our products. To receive service under warranty, the original manufacturer part must be
returned for examination by an authorized service center. Shipping and handling charges may apply. If
a defect is found, NAT will either repair or replace the product at its discretion.
