North American NT-HF007 User manual

尺寸：143mm*210mm
装订成册
材质：封面128克铜版纸，内页80克书纸
印刷时请删除绿色成品框和规范框 不要印上~~

Mirrored Jewelry Cabinet
Model: NT-HF007
Made in China
Assembly Instructions
E-mail: [e-mail]
Address: 505, Bldg 6, Shenglong Garden phase 2,
No.2 Shenglong Rd., Longcheng
St., Longgang Dist., Shenzhen
www.nicetree.co
Manufacturer
Shenzhen Xiaojia Technology Co.Ltd
NORTH AMERICA

Thank you for purchasing the Nicetree Jewelry Cabinet. Please
read this user manual carefully and keep it in a safe place for
future reference. If you need any assistance, please contact our
support team with your product model number and Amazon order
number.

Package Contents
A. 1 x Jewelry Cabinrt
B. 2 x Stands
C. 1 x C wooden base
D. 1 x D Rail Stopper
E. 6 x E Screws
F. 2 x F Screws
I. 1 x Allen Wrench
J. 2 x Dowels
K. 1 x J Screw
L. 1 x K Plastic Screw
G. 2 x Washers
H. 2 x Keys
A. B. C.
D. E. F.
G. H. I.
1 pc
2 pcs
1 pc
2 pcs
2 pcs 2 pcs
6 pcs
1 pc1 pc
J.
2 pcs
K. L.
1 pc
2 pcs
CONTENTS
Package Contents
IMPORTANT
Installation
LED Battery Replacement
Internal Structure
Specifications
Warranty & Customer Support
02
03
05
08
09
10
10
01/02

IMPORTANT
Please read the following instruction carefully and use the product
accordingly. Please keep this manual and hand it over if you transfer the
product. This summary may not include every detail of all variations and
considered steps. Please contact us when further information and help are
needed.
Warnings
1. The product’s primary use is as a mirror and storage cabinet. The user
must strictly assemble and use the product in accordance with this
manual. The seller does not assume any responsibility or liability with
respect to any damage caused by incorrect assembly or improper use.
2. Please check that the cabinet body is intact and the accessories are
complete before mounting. Do not place the edge of the unwrapped
cabinet on the oor to avoid fraying or damage.
3. Follow the assembly steps shown in the diagram to position and adjust
the parts, then gradually tighten all screws. Do not tighten excessively.
4. It is recommended that two adults assemble the cabinet together. Take
care to assemble the cabinet and the stand horizontally and ensure it is
rmly fastened to avoid it falling.
5. Open and close the door gently for long-lasting use of the hinges (the
widest angle of the door is about 100 degrees).
6. Please put the article on the at ground and away from sharp and hard
objects. Do not drag the cabinet across the oor - please lift it up to
move.
7. For daily care, please clean with a soft and dry cloth. If necessary, you
can use neutral detergent. Do not wipe the surface with a wet cloth or
hard objects.
8. Keep the article away from acidic chemicals, so as not to cause a
chemical reaction or discoloration, etc.
Two adults are required for assembly. Please follow the instructions below
step by step.
1. Connect the C wood base to the bottom of the B stand with 2 E screws.
2. Connect the D rail stopper to the middle of the B stand with 1 E screw.
3. Insert the other 2 E screws and half tighten them with the Allen wrench to
connect the C wood base to the other B stand.
4. Insert the other 1 E screw and half tighten them with the Allen wrench to
connect the D rail stopper to the other B stand.
5. Tilt the assembled stand, align holes on the stand, and those on the
cabinet. Put the G washers between the jewelry cabinet and the B stand,
insert 2 F screws and fully tighten all screws including those on the stand.
Assembly
Stand Assembly
9. Keep this product in room with normal temperature. Avoid direct
sunlight and do not place next to heat sources, which can cause the
deformation, distortion, and even cracking.
10. There may be a smell when the packaging is removed. If so, please
place the cabinet in a ventilated area and open the door to remove
the smell.
11. The product is not intended for children. Children must be under
adult supervision to use the product. Otherwise the seller is not liable
for the damage or the injury.
12. Never allow children to climb or play around with the product, in
order to protect children from personal injury and to prevent the
mirror body being broken.
13. During the mounting process, keep small objects out of the reach of
children. It may be fatal if parts are swallowed or inhaled.
14. To avoid danger of suffocation, keep the plastic bag away from
babies and children.
03/04

05/06
6. Insert 2 dowels into the angles locking holes to set the tilting angle of the
cabinet. You may change the hole later if needed.
7. Set up the cabinet. You can open or lock the cabinet with the keys.
8. Fix the standing jewelry cabinet on the wall if you want it to be more stable.
(With K Screw and L Plastic Screw Anchor)






A G B F
OFF
ON
OFF
ON
AAA AAA AAA


07/08
LED Battery Replacement
8 LEDs were installed at the top of the inside of the cabinet during
manufacturing. They are powered by 3 AAA batteries and will light up
automatically when the door is opened.
OFF
ON
Light Switch:
Auto ON with
Door Opened
OFF
ON
AAA AAA AAA
KL

09/10
Warranty & Customer Support
18 months warranty.
If you need any assistance or have any questions, please contact our
store and we will reply within 24 hours. Please leave your order number
and details of your question, so we can help you solve the issue as soon
as possible.
Specications
Material
Mirror Included?
Dimensions
Weight
Real glass, Quality MDF, Soft Velvet
Yes
153 x 41.5 x 37cm / 60.2 x 16.3 x14.6in
14.55kg / 32.1lbs
Internal Structure
Earrings
Ear studs
(Dustproof)
Bracelets
Necklaces
Long
Necklaces
Short
Necklaces
Shelves

www.nicetree.co