Novogratz BAXTER NVZ-BX2SBK-WH User manual

1PB
model# NVZ-BX2SBK-WH
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
BAXTER CONSOLE BOOKCASE

2
TOP PANEL
SIDE PANEL [X2]
PARTITION PANEL [X2]
SHELF PANEL
BOTTOM PANEL
BACK PANEL [X2]
LEG [X4]
A
B
C
D
E
F
G
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Hammer Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Large Cam Cover
x8
3. Cam
x20
4. Small Cam Cover
x8
1. Wood Dowel
x20
2. Cam Bolt
x20
6. Pan Head Screw
x26

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
11. Washer
x10
9. M6x50mm Bolt
x8
10. Lock Washer
x8
7. Metal Plate
x5
8. Allen Wrench
x1
12. Wall Anchor
x1

4 5
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
14. Truss Head Screw
x1
13. Wall Strap
x1
15. Wall Screw
x1

6
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

6 7
x4 x4 x4 x4
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam 4. Small Cam
Cover
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x4 x4 x4
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt 3. Cam

8 9
x1 x8 x8 x8
STEP 3
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
8. Allen
Wrench 9. M6x50mm Bolt 10. Lock
Washer
11. Washer

10
x6 x6 x6 x2
x4
(H4)
STEP 4
1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 6 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Wood
D o w e l
2. Cam Bolt 3. Cam 4. Small Cam
Cover
5. Large Cam
Cover