Novopro U200 User manual
U200 Twin Multi Channel UHF
Handheld Microphone System
Thank you for purchasing the Novopro U200 UHF wireless microphone.
This user manual will help you to set up and understand the operation of the
unit and its features, so please spend a few minutes reading through this information
to ensure correct and reliable operation.
User Manual
1. ON/OFF Power Switch.
2. LED Power indicator
3. Backlit / illuminated LCD information display showing the receiver frequency
channel no. Etc.
4. Down function button for setting the channel number and frequency.
5. Up function button for setting the channel number and frequency.
6. “AF” level indicator, displaying the audio frequency signal level.
7. “RF” signal indicator. Illuminates when the receiver receives the signal
from the transmitter.
8. High gain antenna for improved signal range.
9. 2xXLRbalancedoutputs,withaxedmicrophonelineleveloutput,forusewith
long cable runs.(the XLR’s bypass the volume controls on the front panel for a
high quality, direct audio path)
10. Volume control for the output level of the receiver – operational when using the
‘mixed’ jack socket output only.
11. 6.35mm - ” audio output jack (mixed output from both channels)
12. Power input socket from the supplied AC/DC main adaptor.
U200 Twin Receiver Layout
To change the channel/frequency, simply hold down the UP (3) or DOWN (4) buttons
oneitherthetransmitterorreceiveruntiltheCH(channelnumber)ashesonthe
backlit display (2) Then press the UP or DOWN button to select the desired channel/
frequency. Once this has been selected simply release the button. After 3 seconds,
thedisplaywillstopashingandthefrequencyhasbeenset.Thisproceduremustbe
carried out on both the transmitter and the receiver in order that the frequencies are
matched.TheU200hasa‘ashmemory’meaningthatthefrequencywillstay
selected but after many months/years of not being used, you may need to match/pair
the frequencies again. To check that the frequency is matched between the
transmitter and the receiver, when the handheld microphone switch (5) is set to the
“ON” position, the green “RF” LED will illuminate on the receiver to indicate that RF
(radio frequency) is being received from the transmitter. When you speak into the
microphone(whentheswitchisonthefully“ON”position)thered“AF”LEDwillash
when an audio signal is being received. i.e. the red light will illuminate when you
are speaking. Please ensure that you always carry a spare set of batteries and that
rechargeable batteries (if used) are fully charged.
U200 Microphone
Layout
Changing Channel/Frequency on the Novopro U200
1 7 3 4
10
10
4 3 7
6
55
6
2
8
9 9
11
12
1
6
32
4
5
This product has been manufactured to our high standards at Novopro and has been
QC tested prior to your purchase but if you do encounter any problems with the
Novopro U200, then please check the following before contacting or returning to your
place of purchase:
1)Ensurethebatteriesarenotat;pleasetryanothersetofneworfullycharged
batteries.
2)Makesurethattheaerialsareconnectedcorrectlytotheunit;simplyreleasethe
locking connector on the aerial and gently re-tighten. If you are still encountering
problems,pleaseturnothepowertothereceiverandremovethebatteriesfrom
the transmitter. Wait for 3 minutes then re-power the units.
Wealsosuggestthatyouselectadierentfrequencyifyouareencounteringissues
or have interference problems, please see the section
“Changing channel/frequency on the Novopro U200”.
NOVOPRO U200 SPECIFICATIONS
Operational Carrier Frequencies UHF 863 - 865 MHz
Frequency Stabilization <+/-30ppm
Image Rejection>90dB and Dynamic Range >90dB
Harmonic Distortion <0.5%
Frequency Response 38Hz~17KHz +/-3dB
Receiver Power required: DC13-15V, min. of 500mA
Battery Voltage 3V (2 x 1.5V)
Continuous Usage: approx. 8 hours (using premium quality batteries)
S/N Ratio >103dB and T.H.D. : <1%
RECEIVER Dimensions are:21.5cm x 20.5cm (17 cm exc. aerials) x 4.5cm
HANDHELD TRANSMITTER Dimensions are: 25.2cm x 5cm x 5cm.
For the latest updates and information on the entire Novopro range visit:
www.novopro.co.uk
Novopro products are designed and engineered in the UK and manufactured in
China.
Duetocontinuousproductdevelopments&improvements,specicationsand
appearance are subject to change. © Copyright Novopro Ltd 2014. E&OE.
