Novus NVIP-2C5000ATM User manual

U s e r ’s m a n u a l
( s h o rt f o r m)
NVIP-2C5000ATM

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
2
IMPORTANT SAFEGUARDS AND WARNINGS
EMC (2014/30/EU) and LVD (2014/35/EU ) Directives
CE Marking
Our products are manufactured to comply with requirements of the following directives and national regulations
implementing the directives:
 Electromagnetic compatibility EMC 2014/30/EU.
 Low voltage LVD 2014/35/EU with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as
75VDC and 1500VDC.
WEEE Directive 2012/19/UE
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European Directive on Waste Electrical and Electronic
Equipment (2012/19/UE) and further amendments. By ensuring this product is disposed of correctly,
you will help to prevent potential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. It shall be handed over to the applicable collection point for used up electrical and
electronic equipment for recycling purpose. For more information about recycling of this product, please contact
your local authorities, your household waste disposal service or the shop where you purchased the product.
RoHS Directive 2011/65/UE
Out of concern for human health protection and friendly environment, we assure that our products
falling under RoHS Directive regulations, regarding the restriction of the use of hazardous substances
in electrical and electronic equipment, have been designed and manufactured in compliance with the
above mentioned regulations. Simultaneously, we claim that our products have been tested and do not
contain hazardous substances whose exceeding limits could have negative impact on human health or
natural environment
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed for self
installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices
during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN
USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES
NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE
CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR
THE RESULTS OF SUCH AN ACTION.

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
3
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDISPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQEUSTED TO FAMILIARIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER
-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL
MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and operating
instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is
necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s
manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is
forbidden;
7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,
damp basements);
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not
recommended since it may lead to heat build-up and damaging the device itself as a consequence;
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly
mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted
by qualified personnel with proper authorization, in accordance with this user’s manual.
10. Device should be supplied only from a power sources whose parameters are in accordance with those
specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera
from a power sources with unknown parameters, unstable or not meeting producer’s requirements;
Due to the product being constantly enhanced and optimized, certain parameters and functions described in the
manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com
website in order to access the newest manual
Data included in the following user’s manual is up to date at the time of printing. AAT Holding S.A. holds
exclusive rights to modify this manual. The producer reserves the rights for device specification modification
and change in the design without prior notice.

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
4
TABLE OF CONTENTS.....................................................................................................4
1. FOREWORD INFORMATION .....................................................................................5
1.1. General Characteristics........................................................................................5
1.2. NVIP-2C5000ATM tech specification ...............................................................6
1.3. Camera dimension ..............................................................................................7
1.4. Package contents..................................................................................................7
2. START-UP AND INITIAL IP CAMERA CONFIGURATION .................................8
2.1. Cable connectors..................................................................................................8
2.2. NVIP-2C5000ATM mounting.............................................................................9
2.3. Starting the IP camera........................................................................................10
2.4. Initial configuration via the Web browser.........................................................11
3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................12
3.1. Recommended PC specification for web browser .............................................12
3.2. Connection with IP camera via the Internet Explorer ........................................12
4. WWW INTERFACE - WORKING WITH IP CAMERA.........................................15
4.1. Displaying live pictures......................................................................................15
4.2. Adding a site to the Compatibility View list......................................................16
5. ELECTRIC CONNECTORS AND ACCESORIES .................................................16
5.1. Connecting power supply to the camera. ..........................................................16
5.2. SD card installation ...........................................................................................17
5.3. Connecting alarm inputs and output ..................................................................17
6. RESTORING FACTORY DEFAULTS .....................................................................17
6.1. Restoring software factory defaults....................................................................17
TABLE OF CONTENTS

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
5
1. FOREWORD INFORMATION
1.1. General Characteristics
 Imager resolution: 2 megapixels
 Electronic D/N function
 Min. Illumination from 0,01 (DSS) lx/F=2.0
 Digital Slow Shutter (DSS)
 Digital Noise Reduction (DNR)
 Wide Dynamic Range (WDR) with double scan sensor, 120dB
 Digital Image Stabilization (DIS)
 Defog Function (F-DNR)
 Lens: pinhole f=3.7 mm/F=2.0
 Image processing: 180˚ image rotation, mirror effect, corridor mode
 Privacy zones: 4
 Region of Interest: 8
 Compression: H.264, H.265, M-JPEG
 Interphone
 Max video processing resolution : 1920 x 1080
 Dual stream mode: compression, resolution, speed and quality defined individually for two video
streams
 RTP/RTSP protocol support for video transmission
 Hardware motion detection
 Built-in webserver: camera configuration through the website
 MicroSD/SDHC card support
 Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server,
saving file on micro SD card, alarm output activation ,
 Network protocol support : ONVIF Profile S (2.6) ,HTTP, TCP/IP, IPv4, UDP, HTTPS,
Multicast, FTP, DHCP, DNS, NTP, RTSP, RTP, UPnP, PPPoE, SMTP, RTCP
 Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,
playback and remote IP devices administration
 Power supply: 12VDC
FOREWORD INFORMATION

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
6
FOREWORD INFORMATION
1.2. Specification
Image
Image Sensor 2 MPX progresive scan CMOS sensor 1/2.8” SONY Exmor R STARVIS
Number of Effective Pixels 1945 (H) x 1097 (V)
Min. Illumination
0.05 lx/F2.0 - color mode,
0.05 lx/F2.0 - B/W mode,
0.01 lx/F2.0 - color mode (DSS),
0.01 lx/F2.0 - B/W mode (DSS)
S/N Ratio > 50 dB (AGC off)
Electronic Shutter auto/manual: 1 s ~ 1/20000 s
Digital Slow Shutter (DSS) up to 1 s
Wide Dynamic Range (WDR) yes (double scan sensor) , 120dB
Digital Image Stabilization (DIS) yes
Digital Noise Reduction (DNR) 2D, 3D
Defog Function (F-DNR) yes
Lens
Lens Type pinhole, f=3.7 mm/F2.0
Day/Night
Switching Type electronic D/N function
Switching Mode auto, manual, time
Switching Level Adjustment yes
Switching Delay 0 ~ 180 s
Switching Schedule yes
Network
Stream Resolution 1920 x 1080 (Full HD), 1280 x 720 (HD), 704 x 576, 640 x 480 (VGA), 640 x 360,
352 x 288 (CIF), 320 x 240 (QVGA)
Frame Rate 30 fps for 1920 x 1080 (Full HD) and lower resolutions
Multistreaming Mode 2 streams
Video/Audio Compression H.264, H.265, MJPEG/G.711, RAW_PCM
Number of Simultaneous Connections max. 8
Bandwidth 30 Mb/s in total
Network Protocols Support HTTP, TCP/IP, IPv4, UDP, HTTPS, Multicast, FTP, DHCP, DNS, NTP, RTSP, RTP, UPnP, PPPoE,
SMTP, RTCP
ONVIF Protocol Support Profile S (ONVIF 2.6)
Camera Configuration from Internet Explorer browser
languages: Polish, English, Russian, and others
Compatible Software NMS
Other functions
Privacy Zones 4
Motion Detection yes
Region of interest (ROI) 8
Image Processing 180˚ image rotation, mirror effect, corridor mode
Prealarm/Postalarm up to 5 MB/up to 86400 s
System Reaction to Alarm Events e-mail with attachment, saving file on FTP server, saving file on SD card, alarm output activation
Interfaces
Video Output BNC, 1.0 Vp-p, 75 Ohm
Audio Input/Output 1/1
Alarm Input/Output 2 (NO/NC)/1
RS-485 yes
Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s
Memory Card Slot microSD - capacity up to 128GB
Installation parameters
Dimensions (mm) 33 (W) x 32 (H) x 33 (L) - sensor module
Weight 0.2 kg
Power Supply 12 VDC
Power Consumption 3 W
Operating Temperature -10°C ~ 50°C

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
7
FOREWORD INFORMATION
1.3. Camera dimensions
Camera dimensions are in mm
1.4. Package contents
After you open the package make sure that the following elements are inside:
 IP camera
 Short version of user’s manual
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
Caution:
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular in-
puts, outputs and adjusting elements that the device is equipped with.
Caution:
In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge
protectors is advised. Any damages resulting from surges are not eligible for service repairs.
Caution:
Please note that the wall or ceiling must have enough strength to support the IP Camera.

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
8
2. START-UP AND INITIAL IP CAMERA CONFIGURATION
2.1. Cabel connectors
START-UP AND INITIAL CAMERA CONFIGURATION
No. Color of
connectors Description
1 - RJ-45 female network connector
2 - 12V DC Power In (POWER)
3 White Audio Input
4 Red Audio Output
5 - BNC video output
6 Red Alarm IN1
7 Yellow Alarm IN2
8 White Alarm Out
9 Black RS485

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
9
2.2. NVIP-2C5000ATM mounting
1. Remove the camera bracket (unscrew both of the screws (A)).
2. Mount the camera bracket in the correct location (screw is not included (B)).
3. Place the camera between the forks stand and mount it with two screws (A).
4. Adjust the camera position and tighten the mounting screws (A).
5. (Optional) To install microSD card (not in set included) into the camera, insert it in microSD slot
(C). Before installing microSD card check details in chapter 5.2 of this user’s manual. To enable
recording, you must format the microSD card and configure microSD recording.
6. To adjust the viewing angle power up the camera. Connect to the camera using a web browser or you
can connect camera BNC video output to the analog monitor.
Caution:
Before connecting the camera's power supply, please check the chapter 2.3 and 5.1
START-UP AND INITIAL CAMERA CONFIGURATION
A A
B
C
A A

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
10
2.3. Starting the IP camera
To run NOVUS IP camera you have to connect it via power supply adapter with parameters compatible
with camera power supply specification. Check details in chapter 5.1
Initialization process is then started which can take about 2 minutes. You can then proceed to connect
to the camera via web browser.
The recommended way to start an IP camera and perform its configuration is a connection directly
to the network switch which is not connected to other devices. To obtain further information about
network configuration parameters (IP address, gateway, network mask, etc.) please contact your
network administrator.
 Connection utilising external power supply and network switch
 Connection utilising external power supply directly to the computer
Note :
Power supply adapter is not included. Please use power adapter with parameters specified in user‘s
manual.
START-UP AND INITIAL CAMERA CONFIGURATION
IP Camera
Network transmission - cross over cable
Computer
IP Camera
Network transmission Network transmis-
Network Switch Computer

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
11
START-UP AND INITIAL CAMERA CONFIGURATION
2.4. Initial configuration via the web browser
The default network settings for NVIP-2C5000ATM camera are :
1. IP address= 192.168.1.200
2. Network mask - 255.255.255.0
3. Gateway - 192.168.1.1
4. User name - root
5. Password - pass
Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can
operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from
192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for
camera and PC computer
You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera
yourself or select DHCP mode (DHCP server is required in this method in target network) by using
web browser or by NMS software. When you use DHCP server check IP address lease and its linking
with camera MAC address to avoid changing or losing IP address during device operation or network/
DHCP server breakdown. You have to remember to use a new camera IP address after changing
network parameters.
After network setting configuration has been done, the camera can be connected to a target network.

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
12
3. NETWORK CONNECTION UTILIZING WEB BROSWER
3.1. Recommended PC specification for web browser connections
Requirements below apply to connection with an IP camera, assuming image display in 1920x1080
resolution and 25 fps speed.
1. CPU Intel Core i3 3 GHz or newer
2. RAM Memory min. 4 GB
3. VGA card NVidia GeForce with 512 MB of RAM memory, or equivalent
4. OS Windows 7 / 8 / 8.1 / 10
5. Network card 100/1000 Mb/s
3.2. Connection with IP camera via the Internet Explorer
Caution:
To maintain correct operation as snapshot or video recording you must enable the browser as an
administrator, also to maintain correct operation as playback from the microSD card you must
add IP camera address to Compatibility View in browser settings.
You have to enter camera IP address in the Internet Explorer address bar. If IP address is correct user
login window will be displayed:
Default user is root and default password is pass.
In selection list you can change the display language. The default language is English.
For safety reasons, it is recommended to change default user name and password.
NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
13
If you’re first time running the camera, you will see screen as below.
To correctly camera working, you need a plugin, you have to download and install it as below.
 Click Download and setup and follow the prompts.
NETWORK CONNECTION UTILIZING WEB BROWSER
Please reopen the browser after installing.
Download and setup
Download and setup
Please reopen the browser after installing.

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
14
 Click Install button
 After installation, click Finished button
Caution: In Windows Vista/7/8/10 the ActiveX applet may be blocked by Windows Defender or
User account control. In such case you should allow to run this applet, or simply disable these
functions.
Caution: If the installation fails, changing security settings for the IE browser is required. In order to do
that, please choose: Tools > Internet options > Security tab > Custom level and:
 Under Download unsigned ActiveX controls - select either Enable or Prompt
 Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt
NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
15
WWW INTERFACE - WORKING WITH IP CAMERA
4. WWW INTERFACE - WORKING WITH IP CAMERA
4.1. Displaying live pictures
1. Camera menu:
 Live Video - opens the camera live video
 Playback - opens the camera playback - to maintain correct operation you must add IP camera
address to Compatibility View in browser settings (look at 4.2 chapter)
 Configuration - opens the camera configuration menu
2. Change Password and Sign out buttons - are used to change the password and log off the current
user.
3. Live video preview
4. Stream information
5. Live video menu
 Selection of stream preview
 Selection of camera - option not available
 Selection of additional camera configuration - option not available
 Video button- turn-on/off camera preview output
 Live / Smooth Button- turn-on smooth preview option
 Audio button- turn-on/off audio output
 Interphone button- turn-on/off audio input and output
 Sensor button- turn-on sensor configuration menu
 Snapshot button-make a preview snapshot
 Selection of additional camera configuration - option not available
1.
3.
4.
5.
2.

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
16
4.2 Adding a site to the Compatibility View list
1. Open Internet Explorer, select the Tools button and then select Compatibility View settings (1).
2. Under Add this website, enter the URL of the site you want to add to the list (2), and then select
Add (3).
5. ELECTRIC CONNECTORS AND ACCESORIES
5.1. Connecting power supply to the camera.
The camera can be supplied only by power supplay with parameters compatible with camera
specification to power camera via power in jack.
Information:
Power supply adapter is not included.
SCHEMA OF 12VDC POWER SUPPLY CONNECTOR
Caution : Make sure to follow the correct polarity if connecting the camera to DC power.
Polarity is marked on the power connector.
Caution: In order to provide protection against voltage surges/lightning strikes, usage of
appropriate surge protectors is advised. Any damages resulting from surges are not eligible for
service repairs.
ELECTRIC CONNECTORS AND ACCESORIES
1.
2. 3.

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
17
ELECTRIC CONNECTORS AND ACCESORIES
5.2. SD card installation
Camera supports microSD/SDHC cards with their capacity up to 128GB. In order to install the card
properly, please follow the instructions below:
 Turn the camera off
 Mount microSD card in the socket , according to the picture:
 Turn the camera on
 Format the card using a IP camera.
Click Local Record >Record Directory. Click Modify. In menu click Format button.
A window will appear click OK to start formatting . Wait for the formatting to complete and then
click OK.
5.3. Connecting audio inputs/outputs.
Color Description
White Audio input—Connect to a self-powered microphone for
listen-in audio.
Red Audio output—Connect to anamplifier or self-powered speaker for
intercom/2-way audio
MicroSD card

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
18
5.4 Connecting alarm inputs/outputs.
Alarm input/output connectors are described in the chapter 2.1 of this user’s manual.
Alarm input
 Alarm input connections
Alarm output
Alarm output relay maximum load: 30VDC / 500mA.
 Alarm output connections
6. RESTORING FACTORY DEFAULTS
NOVUS IP camera NVIP-2C5000ATM allow to restore defaults via software (web browser level)
resetting the camera settings
6.1. Restoring software factory defaults
Restoring factory software default can restore default settings of the IP camera, optionally network
settings can be saved.
Logon to the camera and choose MAINTENANCE. Check the Save the IP setting box to preserve IP
setting after restore. Click Restore button. The camera re-starts then, taking about two minutes to
complete. Log on using default user name (root) and password (pass)
ELECTRIC CONNECTORS AND ACCESORIES

NVIP-2C5000ATM User’s manual ver.1.1
(short form)
All rights reserved © AAT Holding S.A.
19
NOTES

2017-07-20 MO, MM
AAT Holding S.A., 431 Pulawska St., 02-801 Warsaw, Poland
tel.: [phone], fax: [phone]
www.novuscctv.com