Novus NVIP-4DN2004V/IR-1P-II User manual

U ser’s manual
( short form)
NVIP-4DN2004V/IR-1P-II

NVIP-4DN2004V/IR-1P-II - User’s manual (short form) ver 1.0
All rights reserved © AAT Holding S.A.
2
IMPORTANT SAFEGUARDS AND WARNINGS
EMC (2014/30/UE) and LVD (2014/35/UE) Directives
CE Marking
Our products are manufactured to comply with requirements of the following directives
and national regulations implementing the directives:
 Electromagnetic compatibility EMC 2014/30/UE..
 Low voltage LVD 2014/35/UE with further amendment. The Directive applies to
electrical equipment designed for use with a voltage rating of between 50VAC and
1000VAC as well as 75VDC and 1500VDC.
WEEE Directive 2012/19/UE
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European 1000VAC Directive on Waste
Electrical and Electronic Equipment (2012/19/UE) and further amendments. By ensuring
this product is disposed of correctly, you will help to prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance
may not be treated as household waste. It shall be handed over to the applicable collection point for
used up electrical and electronic equipment for recycling purpose. For more information about
recycling of this product, please contact your local authorities, your household waste disposal service
or the shop where you purchased the product.
RoHS Directive 2011/65/UE
Information concerning the restriction of use of hazardous substances in electrical electronic
equipment.
Out of concern for human health protection and friendly environment, we assure that our
products falling under RoHS Directive regulations, regarding the restriction of the use of
hazardous substances in electrical and electronic equipment, have been designed and
manufactured in compliance with the above mentioned regulations. Simultaneously, we
claim that our products have been tested and do not contain hazardous substances whose
exceeding limits could have negative impact on human health or natural environment
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed
for self installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other
devices during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN
PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE
PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE
PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING
THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

NVIP-4DN2004V/IR-1P-II - User’s manual (short form) ver 1.0
All rights reserved © AAT Holding S.A.
3
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS SHORT MANUAL IS AN INDESPENSIBLE CONDITION OF A
PROPER DEVICE ISTALLATION AND CONFIGURATION. YOU ARE KINDLY REQUSTED TO
FAMILIRIZE YOURSELF WITH THE FULL USER MANUAL PRIOR TO FURTHER DEVICE
EXPLOATATION. FULL USER MANUAL IS AVAILABLE ON www.novus.com/en
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO
USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE
PERSONNEL MAY OPEN THE UNIT.
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and
operating instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual
is necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the
user’s manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is
forbidden;
7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools,
bath tubs, damp basements);
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)
is not recommended since it may lead to heat build-up and damaging the device itself as a
consequence;
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden.
Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The
camera must be mounted by qualified personnel with proper authorization, in accordance with this
user’s manual.
10. Device should be supplied only from a power sources whose parameters are in accordance with
those specified by the producer in the camera technical datasheet. Therefore, it is forbidden to
supply the camera from a power sources with unknown parameters, unstable or not meeting
producer’s requirements;
Due to the product being constantly enhanced and optimized, certain parameters and functions
described in the manual in question may change without further notice.
We strongly suggest visiting the www.novuscctv.com/en website in order to access the newest manual

NVIP-4DN2004V/IR-1P-II - User’s manual (short form) ver 1.0
All rights reserved © AAT Holding S.A.
4
TABLE OF CONTENTS.................................................................................................4
1. FOREWORD INFORMATION..................................................................................5
1.1. General characteristics .....................................................................................5
1.2. Technical specification ....................................................................................6
1.3. Camera dimension ...........................................................................................7
1.4. Package contents..............................................................................................7
2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................8
2.1. Description of connectors.................................................................................8
2.2. Connecting ethernet cable ................................................................................8
2.3. Camera mounting .............................................................................................9
2.4. Starting the IP camera ....................................................................................10
2.5. Initial configuration via web browser .............................................................11
2.6. Security recommendations for network architecture and configuration ..........12
3. NETWORK CONNECTION UTILIZING WEB BROSWER ...............................13
3.1. Recommended PC specification for web browser............................................13
3.2. Connection with IP camera via web browser...................................................13
4. USING AND CONFIGURING..................................................................................15
4.1. Remote Preview Interface. ..............................................................................15
5. ELECTRIC CONNECTORS ..................................................................................17
5.1. Connecting power supply to the camera. ........................................................17
6. RESTORING FACTORY DEFAULTS ..................................................................17
6.1. Restore factory defaults via web browser ........................................................17
TABLE OF CONTENTS

NVIP-4DN2004V/IR-1P-II - User’s manual (short form) ver 1.0
All rights reserved © AAT Holding S.A.
5
1. FOREWORD INFORMATION
1.1. General Characteristics
 Sensor resolution: 4 megapixels
 Mechanical IR cut filter, IR operation capability
 Min. Illumination from 0 lx with IR LED on
 Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions
 Digital Noise Reduction (DNR)
 Lens type: motorzoom, f=2.7 ~ 13.5mm/F=1.3
 Built-in LED illuminator: 40 pcs LED
 Compression: H.264/H265
 Max video processing resolution: 2592x1520
 Multi streaming: three independently configurable streams
 Stream parameters: compression, resolution, speed and quality defined individually for each
video stream
 RTP/RTSP protocol support for video transmission
 Hardware motion detection
 Hardware sabotage detection (lens shade)
 Built-in webserver: camera configuration through the website
 Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server
 Six advanced image analysis functions
 Four privacy zones
 Eight definable Region of Interest
 Power supply: 12VDC, PoE (Power over Ethernet 802.3af)
Information
Depending on the type of recorder/registration system, the range of features and options may vary. Full
list of camera functionality available from a given type of recorder is included in the instruction manual
on www.novuscctv.com/en
Information!
The manufacturer reserves the right to printing errors and technical specifications changes
without prior notice.
FOREWORD INFORMATION

NVIP-4DN2004V/IR-1P-II - User’s manual (short form) ver 1.0
All rights reserved © AAT Holding S.A.
6
1.2. Technical specification
FOREWORD INFORMATION
Image
Image Sensor 4 MPX CMOS sensor 1/3” OV
Number of Effective Pixels 2688 (H) x 1520 (V)
Min. Illumination 0.06 lx/F1.3 - color mode,
0 lx (IR on) - B/W mode
Electronic Shutter auto/manual: 1/5 s ~ 1/20000 s
Digital Slow Shutter (DSS) up to 1/5 s
Wide Dynamic Range (WDR) yes (double scan sensor), 90dB
Digital Noise Reduction (DNR) 2D, 3D
Defog Function (F-DNR) yes
Back Light Compensation (BLC) yes
Lens
Lens Type motor-zoom, f=2.7 ~ 13.5 mm/F1.3
Auto-focus zoom trigger, day/night mode trigger, manual trigger
Day/Night
Switching Type mechanical IR cut filter
Switching Mode auto, manual
Switching Delay 1 ~ 36 s
Visible Light Sensor yes
Network
Stream Resolution 2592 x 1520, 2304 x 1296, 2048 x 1520, 1920 x 1080 (Full HD),
1280 x 960, 1280 x 720 (HD), 704 x 576, 640 x 480 (VGA), 320 x 240
Frame Rate 20 fps for 2592 x 1520,
30 fps for 2048 x 1520 and lower resolutions
Multistreaming Mode 3 streams
Video/Audio Compression H.264, H.265/-
Number of Simultaneous Connections max. 10
Bandwidth 63 Mb/s in total
Network Protocols Support HTTP, TCP/IP, IPv4, FTP, DHCP, DNS, DDNS, NTP, RTSP, RTP, UPnP,
SMTP
ONVIF Protocol Support Profile S (ONVIF 2.6)
Camera Configuration from Internet Explorer browser
languages: Polish, English, Russian, and others
Compatible Software NMS
Other functions
Privacy Zones 4
Motion Detection yes
Region of interest (ROI) 8
Video Content Analysis (VCA) abandoned object, object disappearance, line cross, zone entrance,
face detection, pedestrian detection, cross counting
Image Processing 180˚ image rotation, corridor mode, vertical flip, horizontal flip
System Reaction to Alarm Events e-mail with attachment, saving file on FTP server

NVIP-4DN2004V/IR-1P-II - User’s manual (short form) ver 1.0
All rights reserved © AAT Holding S.A.
7
FOREWORD INFORMATION
1.3. Camera dimensions
Dimensions are given in millimeters
1.4. Package contents
After you open the package make sure that the following elements are inside:
 IP camera
 Accessories bag
 Short version of user’s manual
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches
the temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
IR LED
LED Number 40
Range 40 m
Angle 120°
Interfaces
Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s
Installation parameters
Dimensions (mm) 135 (Ф) x 128 (H)
Weight 0.7 kg
Degree of Protection IP 66 (details in the user’s manual, page 9)
Enclosure vandal proof aluminium, white
Power Supply PoE, 12 VDC
Power Consumption 2 W,
6 W (IR on)
Operating Temperature -35°C ~ 60°C

NVIP-4DN2004V/IR-1P-II - User’s manual (short form) ver 1.0
All rights reserved © AAT Holding S.A.
8
1
2
2. START-UP AND INITIAL CAMERA CONFIGURATION
2.1. Description of connectors
1. Power supply 12VDC
2. 100 Mb/s Ethernet port (RJ-45 hermetic connector)
2.2. Connecting ethernet cable
To maintain tightness of ethernet cable connection, please follow instruction below:
1. Unscrew the nut (b) from the connector cover (a), mount the sealing ring on the socket (c)
2. Route the network cable through the components (a) and (b). Plug the RJ-45 connector into the
socket (c)
3. Screw the connector cover (a) on the socket (c). Inside the upper part of the connector cover (a) push
in to the stop the seal of the cable (d) - the seal is cut to insert on the network cable.
4. Tighten up to the stop nut (b)
WARNING!
Camera power supply connector is not hermetic. User should seal this connector by himself.
START-UP AND INITIAL CAMERA CONFIGURATION
b a
b
a
c
d

NVIP-4DN2004V/IR-1P-II - User’s manual (short form) ver 1.0
All rights reserved © AAT Holding S.A.
9
2.3. Camera mounting
To mount a camera please follow the instructions below:
 Unscrew the locking ring (A) by turning it counter-clockwise
 Remove the camera cover (B), remove the camera from the base
 Put the bracket or mounting template to the wall in a desired mounting place (with cable hole).
Taking the bracket’s base screw holes as a pattern, mark future drilling holes for screws.
 Drill holes in accordance with previously done markings and base hole placement.
 Mount the camera base using the supplied plugs and screws.
 Connect the camera cables, put camera on the base, attach the cover (B) and pre-tighten the
locking ring (A)
 Adjust camera position, fully screw the locking ring (A)
 Make adjustments to the camera using the on-screen menu (see chapter 4)
WARNING!
Please note that the wall or ceiling must have enough strength to support the IP Camera.
WARNING!
The declared degree of protection of the camera relates to its housing and does not take into
account the possibility of moisture infiltration into the interior of the camera by connecting
cables. Connection cables protection through i.e. sealing up is the responsibility of the camera
installer. The manufacturer is not liable for any damages to the camera caused as a result of
failing in performing that activity by installer, which also means that camera damaged in that
way is not subject to warranty repairs.
START-UP AND INITIAL IP CAMERA CONFIGURATION
A
B

NVIP-4DN2004V/IR-1P-II - User’s manual (short form) ver 1.0
All rights reserved © AAT Holding S.A.
10
START-UP AND INITIAL CAMERA CONFIGURATION
2.4. Starting the IP camera
To run NOVUS IP camera you have to connect ethernet cable between camera and network switch.
To power it up you can connect it directly via power supply adapter with parameters compatible with
camera power supply specification, or camera can be powered with PoE (IEEE 802.3af ) compatible
switch.
After connecting power supply it takes about 30 seconds to start camera. Then You can proceed to
connect to the camera via web browser.
The recommended way to start an IP camera and perform its configuration is a connection directly
to the network switch which is not connected to other devices. To obtain further information about
network configuration parameters (IP address, gateway, network mask, etc.) please contact your
network administrator.
 Connection utilising network switch with PoE support
 Connection utilising external power supply and network switch
Computer
IP camera
Power supply and network
transmission
Network transmission
Network PoE switch
Network transmission
Network transmission
Network switch Computer
IP camera