NST CVD3IP Manual

120326-1
HARDWARE
INSTALLATION GUIDE
Version 1. 0. 2
Released on 1st of April., 2012
CVD3IP 1.3 Megapixel(720P) Indoor Dome IP Camera
CVD3IP
1-512-756-1678

Dear Customers!
INFORMATION
By selecting this product, you have decided to use a professional device that
guarantees highest quality and reliability. We would like to thank you very much for your
confidence and kindly ask you to read the following instructions carefully before
Installation and operation in order to take full advantage of all quality features regarding
this product.
CAUTION
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
The lighting flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
This equipment has been tested and found to comply with limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
CAUTION – To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to
all local codes.
2 3
Table of contents
1. Precautions ------------------------------------------------------------- 4
2. Limitation of liability --------------------------------------------------- 5
3. Disclaimer of warranty ----------------------------------------------- 5
4. Package ----------------------------------------------------------------- 6
5. Cable Connection ----------------------------------------------------- 7
6. Installation ----------------------------------------------------------- 8~9
7. Dimension (mm) ---------------------------------------------------- 10
8. Specification ----------------------------------------------------- 11~12

· Please read the manual carefully before the installation in order to make use the
camera to be set up correctly and to have the best picture quality.
·Please keep the manual in good condition for your future reference and service
application.
·Installation and services should only be carried out by an authorized personnel
according to local safety regulations.
·If any liquid or solid matter gets into the housing, immediately disconnect the camera
from power supply and have it checked by your authorized dealer before reusing.
·Avoid installing the camera at extremely hot or cold places.
·If you are not a certified person, never try to dismantle the camera. To avoid electric
shock, never remove the screws or covers. There are no parts inside that need
maintenance by the user. All maintenance should be carried by qualified personnel.
·Avoid installing the camera at a place of high humidity.
·Avoid installing the camera at the place exposed to gas or oil.
·Keep the top glass of the lens always clean in order to obtain the best picture quality
all the time. Be careful not to be stained by fingerprint.
·Please give a special attention to keep the unit from dangerous drop or
external shock during the process of transportation or handling.
·Never try to touch the camera in wet hand. It may cause an electric shock.
·Do not expose the camera to radioactivity. It causes a serious damage on the sensor.
This publication is provided “AS IS” without warranty of any kind, either express or
implied, including but not limited to, the implied warranties of merchantability, fitness
for any particular purpose, or noninfringement of the third party's right. This publication
could include technical inaccuracies or typographical errors. Changes are added to the
information herein, at any time, for the improvements of this publication and/or the
corresponding product(s).
4 5
1. Precautions 2. Limitation of liability
In no event shall seller be liable to any party or any person, except for replacement or
reasonable maintenance of the product, for the cases, including but not limited to
below :
(1) Any damage and loss, including without limitation, direct or indirect, special,
consequential or exemplary, arising out of or relating to the product;
(2) Personal injury or any damage caused by inappropriate use or negligent operation
of the user;
(3) unauthorized disassemble, repair or modification of the product by the user;
(4) Inconvenience or any loss arising when images are not displayed, due to any reason
or cause including any failure or problem of the product;
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the
system combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being
photogenic subject, due to violation of privacy with the result of that surveillance-
camera's picture, including saved data, for some reason, becomes public or is used
for the purpose other than surveillance.
3. Disclaimer of warranty

6 7
4. Package 5. Cable Connection
Indoor Dome IP Camera
1EA
Instruction manual
1EA
Tapping Screw
3EA
Sponge
1EA
Drilling template
1EA
3-Drilling Hole
50-Template
Power Connector
Network Connector
This IP camera uses 12VDC for power source. Please make sure to use a UL/CE
approved and 12VDC regulated power supply for input power.
☞NOTE
PoE is not available for CVD3IP. Do not connect
PoE device into this product.
CD
‐Hardware Installation Guide (PDF)
‐IP Camera Manual (PDF)
‐NVR Pro Manual
‐NVR Lite (16Ch) Program
‐IPScan Utility Program (IP Installer)

8 9
6. Installation 6. Installation
6-1. Tool-free 3-Axis mounting mechanism 6-2. Installation overview
Perfect 3-axis
PAN ±20°
TITLT 90°
ROTATION 90°
-Panning axis up to ±20 degree
-Tilting axis up to 90 degree
-Rotation axis up to ±90 degree
Drilling template
wall
Tapping screw
PH 3x12L (3EA)
Star Screw M3*8.5L
Sponge plate
Bottom case
Top case

10 11
7. Dimension (mm) 8. Specification
Classificaon Specificaon
General
CPU 32-bit ARM9 RISC CPU up to533MHz,
32KB I/D-Cache, MMU
Video Buffer 16Mbyte VideoFrame Buffer
Flash 16 Mbyte Flash Memory
SDRAM 256Mbyte
Image
Pickup
Image sensor 1.3 Megapixel 1/3" SONY progressive scan
CMOS image sensor
Total Pixels 1384(H) x 1076(V) 1.49 Megapixel
Effecve Pixels 1329(H) x 1049(V) 1.39 Megapixel
S/N Rao More than 50dB
Min. Illuminaon 0.5 Lux with DSSX2 (F1.2, 30IRE, AGC On)
Lens 3.0mm Megapixel Board Lens
Video
Video compression H.264 baseline profile, Moon JPEG
Resoluons Up to720p (1280 X 720)
Frame rate
H.264 Up to30fps at HD(720p)
MJPEG Up to15fps at VGA
(Simultaneous dual stream)
MJPEG single stream up to30 fps at HD(720P)
Video streaming
Support mulstream with H.264, MJPEG
Adjustable frame rate
VBR/CBR inH.264
Pan/Tilt/Zoom Digital PTZ
Image seng
Day & Night
AutoWhite Balance
AutoExposure
Privacy Mask
Effect - Color, Sharpness, Mirror/V-Flip, etc.
Network
Network Security
Password protecon
User access log
HTTPS encrypon
Supported protocol HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DynDNS,
NTP, RTSP, RTP, TCP, UDP, ICMP, DHCP

12 13
MEMO8. Specification
System
integraon
Intelligent video Moon detecon up to 1280x720
with 32x24 blocks
Alarm trigger Moon detecon
Alarm events File upload via p, e-mail
Noficaon via email, FTP and TCP
Video buffer 16MB pre-alarm and post-alarm
Recording Save to Micro SD card with event mode and
connuous mode
Firmware upgrade Remote upgrade via network
API CGI Interface document
AcveX Interface(ocx(dll) + document)
etc RESET Buon 1 x Factory Reset Buon
Physical
Power Source 12VDC
Power Consumpon Max. 4.2W
Net Weight 383g Appr.(Camera Only)
LED's Power, Network Connecon
Dimension 110(Ø) x47.5(H)
IP Grade IP67
Environment
Operang
Temperature -25 degree~50 degree Celsius (-13F~122F)
Storage Temperature -25 degree~60 degree Celsius (-13F~140F)
Soware Included Soware NVR
Lite
(16
Channel),
IP Installer (Windows Only)
Package Package Contents Network Camera, User Manual, Soware CD
* Specifications are subject to change without prior notice for improvement.

14 15
MEMOMEMO

Network Camera & Video Server
USER MANUAL
Version 1.7.1
Released on 1st of Sept., 2011

2
Table of Contents
Safety and Regulatory Notices ......................................................................................................................................3.
Section 1: Product Overview
1.1 About Network Cameras and Video Servers...................................................................................... 5
1.2 Main Features and Benefits ............................................................................................................................ 5
Section 2: Physical Description
2.1 Package Contents ........................................................................................................................................... 6
2.2 Front View of Indoor Box Camera.................................................................................................................... 6
2.3 Other Network Camera and Connector ........................................................................................................... 8
2.4 Network Video Server…..…….......................................................................................................................... 8
Section 3: Installation Summary and Examples .......................................................................................................... 10
Section 4: Assigning an IP address and Accessing the Camera’s Homepage
4.1 Connecting the Camera to a PC ......................................................................................................................11
4.2 Setting Up the IP address Using IPScanUtil Program .................................................................................... 12
4.3 Accessing the Camera’s Homepage ................................................................................................................13
Section 5: Main Page View and Function Icons ............................................................................................................15
Section 6: Administrator Menu
6.1 Overview of the Administrator Menu ............................................................................................................... 18
6.2 Camera Configuration ………………………………………………………………………………………………… 19
6.3 Event Configuration …………………………………………………………………………………………………… 29
6.4 User Configuration …………………………………………………………………………………………………….. 31
6.5 Network Configuration ………………………………………………………………………………………………... 32
6.6 System Configuration ……………………………………………………..………………………………………….. 37
6.7 PTZ Configuration ……………………..…........................................................................................................ 41
Section 7: Glossary of Terms ………………….............................................................................................................. 42

3
About this Document
Thank you for purchasing NST Network Camera or Network Video Server. This user manual includes instructions
for using and managing the camera on your network. Networking experience will be helpful when setting up and
using this product.
Legal Considerations
Video and audio surveillance can be prohibited by laws that vary from country to country. Please check the laws in your
local region before using this product for surveillance purposes.
Electromagnetic Compatibility (EMC)
This equipment generates radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Re-orient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a different circuit than the receiver.
- Consult your dealer or an experienced radio/TV technician for help.
- Check that shielded (STP) network cables are being used with this unit to ensure compliance with EMC standards.
This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Subpart
B of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when
operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference,
in which case the user, at his own expense, will be required to take whatever measures may be required to correct the
interference. This digital equipment fulfills the requirements for radiated emission according to limit B of EN55022/1998,
and the requirements for immunity according to EN55024/1998 residential, commercial and light industry.
Safety
This equipment complies with EN 60950, Safety of Information Technology equipment.
Radio Transmission Regulatory Information
This equipment generates and radiates radio frequency energy, and must be installed and operated while maintaining a
minimum body-to-camera distance of 3 feet (1 meter).
Tested to comply with FCC Standards FOR HOME OR OFFICE USE.
This product must be installed and used in strict accordance with the instructions given in the user documentation.
This product complies with the following radio frequency and safety standards:
Europe -EU Declaration of Conformity.
This device complies with the requirements of the R&TTE Directive 1999/5/EC with essential test suites as per
standards EN 301489: General EMC requirements for radio equipment; and ETS 300328: Technical requirements for
radio equipment.
USA -Federal Communications Commission (FCC): This device complies with Part 15 of FCC Rules. Operation of the
device is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
Trademark Acknowledgments
Ethernet, Internet Explorer, Linux, Microsoft, Mozilla, Netscape Navigator, OS/2, UNIX, Windows, WWW are registered
trademarks of the respective holders. Java and all Java-based trademarks and logos are trademarks or registered
trademarks of Sun Microsystems, Inc. in the United States and other countries.
Video Standard and Product Classification
As the video standard varies from country to country, users are asked to check it first and choose the right model. The
two most common video standards used are NTSC and PAL. NTSC is the video system or standard used in North
America and most of South America. In NTSC, 30 frames are transmitted each second. Each frame is made up of
525 individual scan lines. PAL is the predominant video system or standard mostly used overseas. In PAL, 25 frames
are transmitted each second. Each frame is made up of 625 individual scan lines.

4
To determine your video standard, refer to the lists below.
(Necessary only for i-Series IP Cameras)
PAL: Afghanistan, Algeria, Argentina, Austria, Australia, Bangladesh, Belgium, Brazil, China, Denmark, Finland,
Germany, Hong Kong, Iceland, India, Indonesia, Iraq, Ireland, Israel, Italy, Jordan, Kenya, Kuwait, Liberia, Malaysia,
Netherlands, Nigeria, Norway, New Guinea, Pakistan, Singapore, South Africa, Southwest Africa, Sudan, Sweden,
Switzerland, Thailand, Turkey, Uganda, United Kingdom, United Arab Emirates, Yugoslavia, Zambia
NTSC: Canada, Chile, Costa Rica, Cuba, Dominican Republic, Ecuador, Japan, Mexico, Nicaragua, Panama, Peru,
Philippines, Puerto Rico, South Korea, Taiwan, USA. Users are asked to read the following before using the Pro Series
Network Camera.
Product Classification
Classification Definition
Max. Resolution Frame rate at max. resolution
Mi-Series HD 1280 X 720 30 fps
Important Notices
1. Camera surveillance laws may differ for each country. Contact the local authorities to avoid any surveillance
law violations.
2. Note that the CCD sensor that equipped in Network Camera can be damaged permanently if exposed to direct
sunlight. If your application demands prolonged exposure to sunlight, you should consider equipping it with a
sun visor.
3. Indoor Network Camera is not weatherproof. Be aware of environmental specifications included in the manual.
For outdoor use, use outdoor network camera or a weatherproof case to protect the camera from water,
moisture or temperature (higher or lower than specifications). For camera cleaning, gently wipe with a clean,
dry cloth.
4. Be sure to use only the DC adapter or AC adaptor provided with your camera. Connecting the camera directly
to AC current may cause electrical damage to the camera.
5. Be careful when handling the camera. Physical shocks can cause serious damage.
6. Be sure to mount the camera securely to avoid any personal injuries. Keep the camera out of the reach of
children.
7. If the camera does not operate properly, contact your local distributor. Do not disassemble the product, as that
may void the warranty.
8. Specifications are subject to change without prior notice to enhance the product quality and stability.
9. The contents of this manual may differ from actual products due to product upgrade or enhancement.

5
1: Product Overview
1.1 About NST Network Cameras and Video Servers
The NST Network Cameras and Network Video Server are all-in-one networking devices that contain a digital color
camera (or a connection for analog CCTV cameras), a powerful Web server, an optimized embedded operating
system, hardware for image compression and a physical Ethernet connection. The products do not need any additional
software or hardware. Simply provide power, connect an Ethernet cable and view from any computer on the network.
For the Network Video Server, you need a conventional CCTV camera as your video input source. The NST Network
Cameras and Network Video Servers are ideal for surveillance applications that require high-quality, full-motion video
and audio, as well as comparatively low bandwidth demands on the network. These products provide an easy user
interface for remote access to receive the optimal synchronized video and audio from anywhere, anytime over the
Internet with the popular Internet Explorer Web browser, as easy as surfing any regular Web sites. More than just a
high-performance network camera, the NST Network Cameras and Network Video Server also offer many advanced
features to provide solutions such as remote surveillance, home/business security, audio/video conferencing, motion
detection and more.
NOTE: This user manual includes the Network Video Server whenever it refers to Network Cameras or
Network Cameras.
1.2 Main Features and Benefits
Convenient Operation
The NST Network Camera does not need any additional software or interaction with any other server. The only
software needed is a common Web browser, such as Microsoft Internet Explorer 5.x or above.
Open Standards
The NST Network Camera supports TCP/IP networking, SMTP e-mail, FTP, HTTP and other Internet-related
protocols. The camera can be used in a standard Web Browser and it integrates easily into other www/Intranet
applications and CGI scripts.
External Devices
The auxiliary Input/Output connector on the camera allows you to connect to a variety of external devices, such
as IR sensors, switches and alarm relays.
Security
Your NST Network Camera includes a self-contained Web server, which means that digital images can be secured
like any other Internet host. Your network administrator, using the unit’s security settings in combination with an
organization’s Internet firewall, normally implements data protection. The administrator can decide whether
individuals, groups or the whole world may access the camera. The NST Network Camera supports multi-user
password protection.
Compression and Performance
With a variable frame rate dependent on the image quality and bit rate, the camera delivers H.264 video up to
maximum 30 images per second at HD resolution (1280x720). (For M3i series, 15 frames per second at full HD)
Classification Maximum Resolution Frame rate at Max. Resolution
Mi-Series 1280 X 720 (HD) 30 fps
Dual Mode Compression
For application providers, system integrators and other APs, this camera supports two types of video:
1) H.264 video; 2) M-JPEG compression.

6
Full Duplex Two-Way Audio
Full duplex two-way audio is available by connecting an external microphone and speaker to the camera.
Included Software
IP scan utility for quick installation
NVR software for for viewing and recording multi cameras up to 16 channels in a screen
User Manual pdf version (IP Camera Manual and NVR Manual)
2: Physical Description
2.1 Package Contents
Check all items packed inside the box as listed below.
ITEM DESCRIPTION
Network Camera or Video Server H.264/M-JPEG dual mode Network Camera or Network
Video Server
Installation CD IP scan utility, IP Camera Manual, NVR software and
manual
Power Supply Power adapter and power cord
Bracket Wall bracket & table stand*
User Manual Printed copy manual
* You can use a standard camera stand or tripod for the box type VISION Network Camera.
2.2 Front View of Indoor Box Camera

7
Rear View
Power Connector: Only use the supplied AC adapter to avoid any possible damage from electric shock.
Network Connector: Connect 10Base-T Ethernet or 100Base-TX Fast Ethernet cable. When use PoE, connect
Ethernet cable coming from PoE injector or switch.
Sensor/Alarm Connector: To connect external devices such as infrared sensors, alarms or motion detectors.
Audio-out: Use to connect to an external speaker for audio communication. The audio sent over the network from a
connected client computer can be delivered through this externally connected speaker.
Audio-in: The external microphone for audio input. The live audio can be captured and transmitted to the connected
camera client via the use of this MIC.
RESET: Restore the factory default settings.
Power LED (Green): Once power is supplied to the camera, the green LED will light.
Operating Status LED/Network Activity LED (Yellow): This LED indicates the camera’s operating status. Once
power is supplied and the camera is connected to network, the LED lights and then blinks very fast as long as the video
is transmitted on the network during normal operation. When there is no video transmission, the LED stops blinking.
SD Card Insert Hole : Insert SD Card for local storage
Analog Video Out : Utilizes analog video by connecting to DVR or monitor, or can be connected to video tester when
installing camera.
SD Card Insert Hole
Sensor/Alarm Connector
Status LED
(
Yellow
)
Power LED
(
Green
)
Network Connector
A
nalo
g
Video Out
Power Connector
Micro
p
hone-in
(
Audio-in
)
S
p
eaker-out
(
Audio-out
)
Reset button

8
2.3 Other Network Camera and Connector
IR night vision cameras, dome cameras, speed dome cameras and mini PTZ cameras usually have connectors on the
end of cable coming out of those cameras.
Before connecting, users are asked to check each label on the connector.
2.4 Network Video Server
Front view
Video Input: To input video signal through a coaxial cable
Video Output: To output video signal through a coaxial cable. The output utilizes analog video by connecting to DVR or
monitor.
Power LED (Red): Once power is supplied to the camera, the green LED will light.
Operating Status LED/Network Status LED (Green): This LED indicates the camera’s operating status. Once power
is supplied and the camera is connected to network, the LED lights and then blinks very fast as long as the video is
transmitted on the network during normal operation. When there is no video transmission, the LED stops blinking.
SD Card Insert : Insert SD Card for local storage
A
nalo
g
Video In
A
nalo
g
Video Out
SD Card Insert
Network Status LED
Power LED
Power Connector
Network Connector
Analog Video Out
Alarm/Sensor
Audio-in
Audio-out

9
Rear view
Power Connector: Only use the supplied AC adapter to avoid any possible damage from electric shock.
Alarm/Sensor/RS485 Connector: To connect external devices such as infrared sensors, alarms or motion
detectors as well as camera RS485 line for remote control
Ethernet (Network Connector): Connect 10Base-T Ethernet or 100Base-TX Fast Ethernet cable.
Audio-out: Use to connect to an external speaker for audio communication. The audio sent over the network from a
connected Video Server client can be delivered through this externally connected speaker.
Audio-in: The external microphone for audio input. The live audio can be captured and transmitted to the connected
Video Server client by using of this port.
RESET: Restore the factory default settings.
Power Connector
A
larm/Sensor/RS485 Connector Network Connector
Reset Button
A
udio-in
A
udio-out

10
3: Installation Summary and Examples
1. Connect the Ethernet and power to the VISION Network Camera.
2. Install and launch the IP scan utility program on the enclosed CD.
3. Assign an IP address and network settings.
4. Securely mount the camera. Owners need to refer to the included Hardware Installation guide.
5. Adjust the lens focus.
Installation Example: Wired Camera
Installation Example: Wireless Camera
LAN Switch Route
r
Internet
(
WAN
)
Remote Access
Network Cameras
& Video Servers
Local Access e-mail / FTP / Web Serve
r
Legend (Cable color) :
- Web Browser access to camera
- Access to e-mail, FTP or Web server
- Transmission of AVI files by camera
LAN Switch Route
r
Internet
(
WAN
)
Remote Access
Wireless Network
Cameras
Local Access e-mail / FTP / Web Serve
r
Legend (Cable color) :
- Web Browser access to camera
- Access to e-mail, FTP or Web server
- Transmission of AVI files by camera
Wireless
Access Point

11
Installation Example: Network Video Server
4. Assigning an IP Address and Accessing the Camera’s Homepage
4.1 Connecting the Camera to a PC
Connect with a direct cable (non-crossover UTP cable) when connecting the camera to a switch, hub or router.
Or connect Network Camera directly to PC using crossover UTP cable.
Remote Access
Network Video Serve
r
CCTV Camera
Analog BNC Input
Analog BNC Output TCP/IP RJ45 Ethernet
Network
(
WAN/LAN
)
DVR
,
VCR
,
Monitor
,
etc.

12
4.2 Setting up the IP Address Using IPScanUtil program in the packaged CD
To access the camera, you need to assign an appropriate network IP address. Run the IP address installation program
(IPscanUtil.exe) on a PC that is connected to the same local network as the camera. You can download IPscanUtil
program from http://www.visionipvideo.com.
1. Run IPscanUtil.exe after the camera is booted (wait until the Operating Status LED blinks very fast).
2. Click “Scan” button.
3. Once IPscanUtil program scanned, the panel shows every camera connected on the local network. From the
cameras listed, select one and click “IP Change” (Or double click the selected camera on the list) to assign a new IP
address (every VISION Network Camera has a factory default IP address. http://192.168.1.100 for wired cameras and
http://192.168.10.100 for wireless cameras).
NOTE: The MAC address can be found on the label of the camera. To choose a camera, click on its MAC address on
the list.
Enter the administrator ID and password in the blank (default ID and password are “admin" and “1234” respectively.) to
assign or change the IP address for the camera and setup.
Enter the IP address, gateway address, subnet mask address, DNS server address and server IP address assigned by
the network administrator. (When the addresses are not assigned properly, you cannot access the camera.) The server
IP address does not need to be filled out at this time.
After entering all addresses for the camera, click on "Change IP" button.
The message shows up if all the information is set up properly.
Then click the "OK" button.
Table of contents
Other NST IP Camera manuals