Nuie NSBS1 User manual

PLEASE CHECK CAREFULLY PACKING LIST TO ENSURE THAT ALL PARTS ARE INCLUDED.
NSBS1 & NSBSR1 - INSTALLATION GUIDE
STRAIGHT GLASS SCREEN PANEL ASSEMBLY
WALL CHANNEL x1
4 x 30 SCREWS x4
WALL PLUGS x4
TOP BAR WALL FIXING x1
C/L
100
SCREW CAPS x3
INNER SCREW CUPS x3
4 x 10 SCREWS x3
(Fitted on the inside)
MAGNETIC SEAL x1
ADJUSTABLE WALL CHANNEL
MAGNETIC SEAL
90° TOP BAR CONNECTOR (520 x 19 x 0.7)
WALL PLUGS
4mm x 30mm SCREWS
4mm x 10mm SCREWS
SCREW COLLAR
SCREW COVER CAP
HINGES
STRAIGHT RETURN GLASS PANEL
GHCS 08-INS029-AA Jan 2023
6mm GLASS
Fig.1
Fig.3
HINGE & MAGNETIC SEAL FIXING
Fig.2
x2
x3
x3
x3
x4
x4x1
x1
x1
x1
x1
STRAIGHT RETURN
GLASS PANEL x1
x1
STRAIGHT RAIL x1
(NSBSR1 ONLY)
x1
NSBSR1 ONLY - STAINLESS STEEL STRAIGHT RAIL
BOTTOM WATER SEAL (180mm)
HINGES x2
BOTTOM WATER
SEAL x1

NSBS1 & NSBSR1 Square Shower Bath Screen (Hinged)
Fitting Instruction
Installation Steps:
1. Insert the large screen side pillar into the aluminium wall channel.
2. When the bath screen has been aligned, mark the position of the wall channel on the wall.
Remove the screen, re-align the wall channel and mark the wall channel screw hole positions
on the wall.
3. Using a 4mm masonary drill bit, drill 3 x 35mm deep holes in the marked screw positions on
the wall.
4. Insert the 3 x wall plugs into the holes and using a rubber hammer knock them in until they fit
flush with the wall.
5. Attach the adjustable wall channel using 3 - 4mm x 30mm screws.
6. Insert the side pillar into the wall channel.
7. Adjust the position of the bath screen assembly until it is level (parallel) with the bath.
8. From inside of the bath screen assembly, make a mark on the wall channel approx’ 100mm
from the top (see fig.2)
Note: The wall channel design, allows for the shower screens to be adjusted so that they
can be used on wall surfaces that are not vertical. When marking the hole positions, please
check to ensure that the hole drilled will go through both the wall channel and side pillar.
9. Using a 3.2mm diameter HS Twist drill bit, drill one hole through the upper marked hole
position. The hole must be drilled through the wall channel & side pillar until it reaches the
centre (DO NOT DRILL THROUGH BOTH SIDES)
10. Secure the upper section of the wall channel to side pillar by using 1 x inner screw support cup
and 1 -4mm x 10mm screw (DO NOT OVER TIGHTEN)
11. Ensuring that the bath screen is still aligned as required, mark the position of the lower bath
screen support screw position approx’ 100mm from the bottom of the wall channel.
12. Repeat the fixing method for wall channel and side pillar in the central fixing point.
13. Locate the screw caps x 3 onto the inner screw support cups.
14. Find the right position for the Top Bar wall fixing and drill into the wall as in Step 12. Fix the
Top Bar wall fixing with the screw & plug provided.
15. Fit the hinges to the large glass screen with the Allen key supplied. Ensure that the fixing bolts
are facing inwards. DO NOT OVER TIGHTEN
16. Attach the small glass screen to the hinges.
17. Close the return glass panel against the large bath screen to fit the vertical magnetic water
seal. Fit the seal onto the large and small screen edge ensuring that the magnets meet when
fully opened. Trim off any excess.
18. Fit the bottom water seal to the underside of the small screen and trim off the excess.
19. Silicone the bottom of the bath screen on the outside at the point where it meets the bath.
With Rail ONLY - Assemble and fix through the holes in the Bath Screen.