Nuova Marea NM-251A User manual

nuova marea ltd
marine electronics & design
Address: 26 Mirtidiotissis str, Kastella, 18533 Piraeus, Greece
Tel.: [phone], Fax: [phone]
website: www.nuovamarea.com e-mail: [email protected]
Page | 1
NM-251A
NMEA-0183 Multiplier
User Guide
V1.03
Introduction
The NM-251A is a two channel NMEA-0183
input / four or five channels NMEA-0183 output
multiplier. It enables data distribution from two
NM-0183 sources (primary and secondary with
priority encoding) to all NMEA-0183 instruments
through four or five talker ports and PC connection
through RS-232. Data from PC’s charting system
can be delivered back to the autopilot from the
same RS-232 port which acts bidirectional (talker
and listener).
Operation
The NM-251A acquires NMEA-0183 sentences from the most significant input and immediately sends
them to the general purpose outputs and the RS-232 output. A watchdog timer routine supervises if the NMEA
signals are correctly applied in the primary input and switches to the secondary input whenever there is no
NMEA sentence for at least eight seconds. In this case the secondary input starts receiving data if there is an
instrument attached. If not, the device automatically returns to the primary input after eight seconds. When the
secondary input is already in receiving mode and an NMEA signal is applied to the primary port, the device
immediately switches to the primary input. In the case that no signal is applied to any input, the device “circles”
around sampling the two listener ports every eight seconds until an NMEA-0183 signal appears to any of the two
listener ports.
In addition the NM-251A can deliver at the same time different NMEA signals connected to Ina and Inb
to output ports Out1/2 and Out3/4 respectively. To select this function user should turn the SW-1 to ON position
at the dip switch array SW1 (see figure 4) located inside the NM-251A. In this mode the user can select from
which input port signals will be delivered to RS232 interface by setting SW-2 to “OFF” position for Ina or “ON”
for Inb.
Input Ports (listeners)
The NM-251A has two input ports that can be connected to any instrument indented for marine use that
can output NMEA-0183 signals. Each one of the two listener ports is optoisolated as specified in NMEA-0183
protocol, thus data(-) pole should never been connected to NM-251A ground. If the instrument’s talker port is
single ended, connect that terminal to the Ina(+) or Inb(+) input and tide the Ina(-) or Inb(-) to instrument’s
ground. If a RS-232 signal level is connected the ground pole (GND) should be connected to Ina(+) or Inb(+)
and the data pole (TXD) to Ina(-) or Inb(-) respectively.
The two listener ports can acquire NMEA sentences carried in TTL, RS-232 and RS-485/422 signal levels.

nuova marea ltd
marine electronics & design
Address: 26 Mirtidiotissis str, Kastella, 18533 Piraeus, Greece
Tel.: [phone], Fax: [phone]
website: www.nuovamarea.com e-mail: [email protected]
Page | 2
Output Ports (Talkers)
Each of the four general purpose talker ports produce NMEA sentences in both RS422 and TTL signal
levels, depending on the connection topology chosen (see figure 1, 2 and 3), and can fan out one instrument.
Current drawn from every port can be up to 20mA, efficient enough to drive any NMEA compatible instrument.
The RS-232 port can deliver NMEA sentences to any modern computer running the appropriate software
on Windows 98 and above provided that serial communication follows the 4.800/8/N/1. This port is not optically
isolated and should be used for testing purposes only to avoid DC leakage. It can be used though to interface a
computer system if proper isolation is achieved or if the computer is supplied from an isolated power supply.
The Out5 port has two functionality modes that can be selected via jumper J6 located inside NM-251A
(see figure 4). By shorting poles 1-2 on J6, Out5 converts signals received from computer to RS-422 signal
level. This functionality is independent from the rest of the NM-251A circuits and is intended to be used for
interfacing Electronic Charting Systems (ECS) with autopilot systems. By shorting poles 1-3 on J6, Out5 is
configured as a fifth output of the NM-251A. Further details on how to configure the functions of the NM-251A
are shown on table 1.
The NM-251A can be connected as shown in figures 1,2 and 3 using all RS-422 outputs (figure 1), all
TTL outputs (figure 2) or using either the RS-422 or TTL output of each port taking care not to connect the
same port for both signal level outputting.
Figure 1: Connection to RS-422 Outputs

nuova marea ltd
marine electronics & design
Address: 26 Mirtidiotissis str, Kastella, 18533 Piraeus, Greece
Tel.: [phone], Fax: [phone]
website: www.nuovamarea.com e-mail: [email protected]
Page | 3
Figure 2: Connection to TTL outputs
Figure 3: Combined use of TTL and RS-422 outputs

nuova marea ltd
marine electronics & design
Address: 26 Mirtidiotissis str, Kastella, 18533 Piraeus, Greece
Tel.: [phone], Fax: [phone]
website: www.nuovamarea.com e-mail: [email protected]
Page | 4
Power Supply
The NM-251A can be powered within the range of 10-35 VDC. The nominal voltage of 24 Vdc is advised
for powering the device in normal operation.
Power input port has a protection for incorrect polarity connection of the supplying voltage.
LED Indicator sequence
Inb LED
ON: Currently sampling from secondary port Inb
Ina LED
ON: Currently sampling from primary port Ina
Out 3/4 LED
Flashing indicates data transmission to output port 3 and 4
Out 1/2 LED
Flashing indicates data transmission to output port 1 and 2
Out5 LED
Flashing indicates reception from RS-232 port and transmission to Out5 port
Dip Switch Settings
Configuration
Input – Output
routing
Functionality Description
SW
1 SW 2 SW 3 SW 4 J5 J6 Out 1/2 Out 3/4
RS
232
Out
5
OFF X OFF OFF 1-2 1-2
Ina
or
Inb
RS
232
RXD
Selects input priority encoding mode. Ina or Inb is
transmitted to Out 1-
4 and RS232. Out5 is converting RXD
channel from RS232. Baud rate at 4.800 bps
OFF X OFF OFF 1-2 1-3
Ina
or
Inb
Selects input priority encoding mode. Ina or Inb is
transmitted to Out 1-5 and RS232. Baud rate at 4.800 bps
(default).
OFF X OFF OFF 1-3 1-2
Ina
or
Inb
RS
232
RXD
Selects input priority encoding mode. Ina or Inb is
transmitted to Out 1-
4 and RS232. Out5 is converting RXD
channel from RS232. Baud rate is free up to 38.400
bps.
CPU does not process the input signals.
OFF X OFF OFF 1-3 1-3
Ina
or
Inb
Selects input priority encoding mode. Ina or Inb is
transmitted to Out 1-5 and RS232. Baud rate is
free up to
38.400 bps. CPU does not process the input signals.
ON OFF OFF OFF 1-2 1-2 Ina Inb Ina
RS
232
RXD
Selects transmission from Ina to Out1/2 and RS232 and
from Inb to Out 3/4. Out5 is converting RXD channel from
RS232. Baud rate at 4.800 bps.
ON OFF OFF OFF 1-2 1-3 Ina Inb Ina Ina
Selects transmission from Ina to Out1/2, RS232 and Out5
and from Inb to Out 3/4. Baud rate at 4.800 bps.
ON OFF OFF OFF 1-3 1-2 Ina Inb Ina RS 232
RXD
Selects transmission from Ina to Out1/2 and RS232 and
from Inb to Out 3/4. Out5 is converting RXD channel from
RS232. Baud rate is free up to 38.400
bps. CPU does not
process the input signals.
ON OFF OFF OFF 1-3 1-3 Ina Inb Ina Ina
Selects transmission from Ina to Out1/2, RS232 and Out5
and from Inb to Out 3/4. Baud rate is free up to 38.400
bps. CPU does not process the input signals.
ON ON OFF OFF 1-2 1-2 Ina Inb Inb RS 232
RXD
Selects transmission from Ina to Out1/2 and from Inb to
Out3/4 and the RS232
. Out5 is converting RXD channel
from RS232. Baud rate at 4.800 bps.
ON ON OFF OFF 1-2 1-3 Ina Inb Inb Inb
Selects transmission from Ina to Out1/2 and from Inb to
Out3/4 and Out5 and RS232. Baud rate at 4.800 bps.
ON ON OFF OFF 1-3 1-2 Ina Inb Inb RS 232
RXD
Selects transmission from Ina to Out1/2 and from Inb to
Out 3/4 and RS232
. Out5 is converting RXD channel from
RS232. Baud rate is free up to 38.400
bps. CPU does not
process the input signals.
ON ON OFF OFF 1-3 1-3 Ina Inb Inb Inb Selects transmission from Ina to Out1/2
and from Inb to
Out 3/4 Out5 and RS232. Baud rate is free up to 38.400
bps. CPU does not process the input signals.
Note:
SW-3 and SW-4 are intended for future use and should not be configured
Table 1: NM-251A Configuration

nuova marea ltd
marine electronics & design
Address: 26 Mirtidiotissis str, Kastella, 18533 Piraeus, Greece
Tel.: [phone], Fax: [phone]
website: www.nuovamarea.com e-mail: [email protected]
Page | 5
Printed Circuit Board composite layout
Figure 4: Composite layout of NM-251A printed circuit board
Specifications
Supply Voltage
9 to 35 VDC
Power Supply Protection PTC Resettable Fuse
Vmax: 60V, Imax: 40A, Ihold: 0,25A (23°C),
Itrip:0,5A (23°C), Max time to trip (23°C): 2,2sec for 1,25A
Current Consumption
50mA in idle state/ 150mA in full output mode
Inputs
2 x NMEA-0183, optically isolated
Common Mode Rejection: 10kV/usec, Isolation: 480 Vrms
Input Resistance
1,5 KOhm
Outputs
4 x buffered RS-422/TTL (general purpose)
1 x RS-232
1 x RS-422 signal conversion from RS-232 RXD channel or as fifth output
Output protection
Buffered for all RS-422 outputs
Speed for NMEA inputs
•4.800/8/N/1 when input priority encoding mode is selected
•Same as listeners connected to output ports when Ina to Out1/2 and Inb to
Out3/4 mode is selected
Speed for NMEA outputs
•4.800/8/N/1 when input priority encoding mode is selected
•Same as listeners connected to output ports when Ina to Out 1/2 and Inb to Out
3/4 mode is selected
4.800/8/N/1 for RS-232 or baud rate free user selectable
Indicators Most Significant Input (Ina)
Less Significant Input (Inb)
Data transmission from output ports 1 and 2 (Out 1/2 LED)
Data transmission from output ports 3 and 4 (Out 3/4 LED)
Data reception from RS-232 interface or output 5 port (Out 5 LED)
Dimensions
Width = 110mm/134,80 mm
Depth = 82 mm
Height = 43 mm
Housing
Styrene

nuova marea ltd
marine electronics & design
Address: 26 Mirtidiotissis str, Kastella, 18533 Piraeus, Greece
Tel.: [phone], Fax: [phone]
website: www.nuovamarea.com e-mail: [email protected]
Page | 6
Port ID Wire ID / Color Cable ID Signal Description
Vin(+)
GND
Ina(+)
Ina(-)
Inb(+)
Inb(-)
Out1A
Out1B
GND
Out2B
Out2A
Out3A
Out3B
GND
Out4B
Out4A
Out5A
Out5B
SETTINGS
J5*
J6*
Dip Switches**
2 1 3 2 1 3 ID OFF ON
1
* Mark the positions that are occupied by the jumper
** Mark the position for every switch
2
3
4
NOTES:

nuova marea ltd
marine electronics & design
Address: 26 Mirtidiotissis str, Kastella, 18533 Piraeus, Greece
Tel.: [phone], Fax: [phone]
website: www.nuovamarea.com e-mail: [e-mail]
Page | 7

nuova marea ltd
marine electronics & design
Address: 26 Mirtidiotissis str, Kastella, 18533 Piraeus, Greece
Tel.: [phone], Fax: [phone]
website: www.nuovamarea.com e-mail: [email protected]
Page | 8