NUVOO NVO-SF40BK User manual

16”(40cm) Stand Fan
Instruction Manual
NVO-SF40BK
WARNING To reduce the risk for fire, electric shock or personal injury
•Do not use this fan with any solid-state speed control device.
•Unplug the fan before cleaning or servicing.
•If you disassemble your fan, completely re-assemble before plugging into outlet.
•To reduce the risk of electric shock and injury to persons, do not use in window.
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
This fan is for residential use only. It is not intended for use in commercial or industrial
settings.

2
Important instructions
Read and save these important safety
instructions before using this fan, when
using electrical appliances, basic safety
precautions should always be followed
including the following:
WARNING - To reduce the risk of fire or
electrical shock, do not use this product
with any solid state speed control device.
To reduce the risk of fire or electric shock
and injury to persons, do not use in a
window.
- Use this fan only as described in this
manual. Other uses not recommended
may cause fire or electric shock.
- This product is intended for
HOUSEHOLD USE ONLY and not for
commercial, industrial or outside use. To
protect against electrical shock, do not
place fan in window, immerse unit, plug
or cord in water, or spray with liquids.
- Unplug the fan from the outlet when not
in use, when moving fan from one
location to another and before cleaning.
- Do not operate the fan in the presence
of explosive and/or flammable fumes.
- Do not place the fan or any parts near
an open flame, cooking or other heating
appliance.
- Avoid contact with moving fan parts.
- To disconnect, grip the plug and pull it
from the wall outlet. Never yank the
cord.
- The use of attachments is not
recommended and may cause hazards.
- Always use on a dry, level surface.
- Do not operate if the fan housing is
removed or damaged.
- Do not operate any fan with a damaged
cord or plug.
- Discard fan or return to an authorized
service facility for examination and/or
repair.
- Do not run cord under carpeting. Do
not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances.
- Arrange cord away from traffic area and
where it will not be tripped over.
- The appliance is not to be used by
persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children being supervised not to play
with the appliance.
- This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved.
- Children shall not play with the
appliance.
- Cleaning and user maintenance shall
not be made by children without
supervision.
- If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in
order to avoid a hazard.
Assembly
1. Place the base on a flat surface.
Remove the locking mechanism from
the pole and insert the pole onto the
base.
2. Turn over the base with the pole
inserted and secure by turning the
locking mechanism clockwise until
completed fastened.
3. Place the motor assembly and
control panel onto the extension pole

3
and secure by turning the assembly
knob clockwise.
4. Remove the rear grill mounting nut
by turning it counter-clockwise.
5. Place the rear grill onto
the motor housing
aligning the 3 raised
knobs on the top of the
motor housing with the
3 holes on the grill.
6. Place the rear grill
mounting nut and
tighten turning clockwise.
7. Align the blade onto the
shaft and secure it by
tightening the blade
knob counter-clockwise.
8. Fix the front grill and the
rear grill with the circlip
and fasten the ring
around the grill. You will
hear a click sound
around the grill.
9. Then use the fasten clip
to tighten the fan grill.
10. Secure further with the
screw and tighten with a
screw driver.
How to operate
1. Set the fan on a level surface.
2. Making sure the speed control is at
OFF position.
3. Plug the power cord into the socket.
Remote Control
1. Press down on the battery
compartment cover and slide it out.
2. Insert 2 x AAA batteries (not included),
making sure that they positive
terminals are facing the proper way.
3. Replace cover.
OFF: allows to switch off the fan.
ON/SPEED: allows to switch on and set
the desired speed.
TIMER: allows to set the working time:
1,2,4 or 7.5 hours.
Cleaning
1. Be sure your fan is in the OFF position.
2. Unplug the fan before cleaning.
3. Use only a soft, damp cloth to gently
wipe the fan.
4. Do not immerse the fan in water and
never allow water to enter the Motor
Housing.
5. Do not use gasoline, paint thinner or
other chemicals to clean the fan.
Removal of front grill for cleaning
1. To access the fan blade, remove the
front grill and securing screw.
2. Clean the fan blade, front and rear
grills with a soft, moist cloth.
3. Replace blade, tighten securing screw
and securely fasten the front grill.

4
Description of parts
1. Front grill
2. Grill protective ring
3. Fasten clip
4. Blade knob
5. Blade
6. Rear grill mounting nut
7. Rear grill
8. Shaft
9. Handle
10. Oscillating pin
11. Motor assembly
12. Neck
13. Control panel
14. Assembly knob
15. Pole
16. Height adjuster
17. Base
18. Locking mechanism
19. Remote control unit