Nuvoton NuMicro NuMaker-NUC029L User manual

NuMaker-NUC029L
Dec. 26, 2022 Page 1of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
NuMicro® Family
Arm®Cortex®-M0-based Microcontroller
NuMaker-NUC029L
User Manual
Evaluation Board for NuMicro®NUC029xAN Series
The information described in this document is the exclusive intellectual property of
Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.
Nuvoton is providing this document only for reference purposes of NuMicro microcontroller and
microprocessor based system design. Nuvoton assumes no responsibility for errors or omissions.
All data and specifications are subject to change without notice.
For additional information or questions, please contact: Nuvoton Technology Corporation.
www.nuvoton.com

NuMaker-NUC029L
Dec. 26, 2022 Page 2of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
Table of Contents
1OVERVIEW......................................................................................................7
2FEATURES......................................................................................................8
3HARDWARE CONFIGURATION.....................................................................9
3.1 Front View....................................................................................................................... 9
3.2 Rear View ..................................................................................................................... 10
3.3 Extension Connectors................................................................................................. 11
3.3.1 Pin Assignment for Extension Connectors .................................................................11
3.3.2 Arduino UNO Compatible Extension Connectors......................................................14
3.4 Power Supply Configuration ...................................................................................... 16
3.4.1 VIN Power Source..........................................................................................................16
3.4.2 5 V Power Sources ........................................................................................................16
3.4.3 3.3 V Power Sources .....................................................................................................17
3.4.4 1.8 V Power Sources .....................................................................................................17
3.4.5 Power Connectors..........................................................................................................17
3.4.6 USB Connectors .............................................................................................................18
3.4.7 Power Switches ..............................................................................................................18
3.4.8 Power Supply Models ....................................................................................................18
3.5 Ammeter Connector.................................................................................................... 21
3.6 Push Buttons................................................................................................................ 22
3.7 LEDs.............................................................................................................................. 23
3.8 Nu-Link2-Me................................................................................................................. 23
3.8.1 VCOM Switches..............................................................................................................23
3.8.2 Status LEDs ....................................................................................................................24
4QUICK START...............................................................................................25
4.1 Toolchains Supporting ................................................................................................ 25
4.2 Nuvoton Nu-Link Driver Installation.......................................................................... 25
4.3 BSP Firmware Download ........................................................................................... 27
4.4 Hardware Setup........................................................................................................... 27
4.5 Find the Example Project ........................................................................................... 29
4.6 Execute the Project under Toolchains...................................................................... 29
4.6.1 Keil MDK..........................................................................................................................29
4.6.2 IAR EWARM....................................................................................................................33
4.6.3 NuEclipse.........................................................................................................................35
5NUMAKER-NUC029L SCHEMATICS ...........................................................41
5.1 Nu-Link2-Me................................................................................................................. 41
5.2 NUC029 Target Board ................................................................................................ 42

NuMaker-NUC029L
Dec. 26, 2022 Page 3of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
5.3 Extension Connectors................................................................................................. 43
5.4 PCB Placement ........................................................................................................... 44
6REVISION HISTORY .....................................................................................45

NuMaker-NUC029L
Dec. 26, 2022 Page 4of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
List of Figures
Figure 1-1 NuMaker-NUC029L Evaluation Board............................................................................ 7
Figure 3-1 Front View of NuMaker-NUC029L.................................................................................. 9
Figure 3-2 Rear View of NuMaker-NUC029L ................................................................................ 10
Figure 3-3 NUC029LAN Extension Connectors............................................................................. 11
Figure 3-4 Arduino UNO Compatible Extension Connectors......................................................... 14
Figure 3-5 External Power Supply Sources on Nu-Link2-Me ........................................................ 18
Figure 3-6 External Power Supply Sources on NUC029 Target Board......................................... 19
Figure 3-7 Detach the Nu-Link2-Me from NuMaker-NUC029L...................................................... 20
Figure 3-8 Wiring between Ammeter Connector and Ammeter..................................................... 22
Figure 3-9 Project Path of SYS_PowerDown_MinCurrent ............................................................ 22
Figure 4-1 Nu-Link USB Driver Installation Setup.......................................................................... 25
Figure 4-2 Nu-Link USB Driver Installation.................................................................................... 26
Figure 4-3 Open VCOM Function .................................................................................................. 27
Figure 4-4 ICE USB Connector...................................................................................................... 27
Figure 4-5 Device Manger.............................................................................................................. 28
Figure 4-6 PuTTY Session Setting................................................................................................. 28
Figure 4-7 Template Project Folder Path....................................................................................... 29
Figure 4-8 Warning Message of “Device not found” ...................................................................... 29
Figure 4-9 Project File Migrate to Version 5 Format...................................................................... 30
Figure 4-10 Debugger Setting in Options Window......................................................................... 30
Figure 4-11 Programming Setting in Options Window................................................................... 31
Figure 4-12 Compile and Download the Project............................................................................ 31
Figure 4-13 Keil MDK Debug Mode............................................................................................... 32
Figure 4-14 Debug Message on Serial Port Terminal Windows.................................................... 32
Figure 4-15 IAR EWARM Window................................................................................................. 33
Figure 4-16 Compile and Download the Project............................................................................ 33
Figure 4-17 IAR EWARM Debug Mode ......................................................................................... 34
Figure 4-18 Debug Message on Serial Port Terminal Windows.................................................... 34
Figure 4-19 Import the Project in NuEclipse .................................................................................. 35
Figure 4-20 Import Projects Windows............................................................................................ 35
Figure 4-21 Open Project Properties Window ............................................................................... 36
Figure 4-22 Project Properties Settings......................................................................................... 36
Figure 4-23 Build Project................................................................................................................ 37
Figure 4-24 Open Debug Configuration......................................................................................... 37
Figure 4-25 Main Tab Configuration .............................................................................................. 38
Figure 4-26 Debugger Tab Configuration ...................................................................................... 38

NuMaker-NUC029L
Dec. 26, 2022 Page 5of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
Figure 4-27 Startup Tab Configuration .......................................................................................... 39
Figure 4-28 NuEclipse Debug Mode.............................................................................................. 40
Figure 4-29 Debug Message on Serial Port Terminal Windows.................................................... 40
Figure 5-1 Nu-Link2-Me Circuit...................................................................................................... 41
Figure 5-2 NUC029 Target Board Circuit....................................................................................... 42
Figure 5-3 Extension Connectors Circuit ....................................................................................... 43
Figure 5-4 Front Placement ........................................................................................................... 44
Figure 5-5 Rear Placement............................................................................................................ 44

NuMaker-NUC029L
Dec. 26, 2022 Page 6of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
List of Tables
Table 3-1 Extension Connectors.................................................................................................... 11
Table 3-2 NUC029LAN Full-pin Extension Connectors and GPIO Function List .......................... 13
Table 3-3 Arduino UNO Extension Connectors and NUC029LAN Mapping GPIO List................. 15
Table 3-4 Vin Power Source.......................................................................................................... 16
Table 3-5 5 V Power Sources........................................................................................................ 16
Table 3-6 3.3 V Power Sources..................................................................................................... 17
Table 3-7 1.8 V Power Sources..................................................................................................... 17
Table 3-8 Power Connectors ......................................................................................................... 17
Table 3-9 USB Connectors ............................................................................................................ 18
Table 3-10 Power Switches ........................................................................................................... 18
Table 3-11 Supply External Power through Nu-Link2-Me ............................................................. 19
Table 3-12 Supply External Power for NUC029 Target Board ...................................................... 21
Table 3-14 Ammeter Connector..................................................................................................... 21
Table 3-15 Push Buttons................................................................................................................ 22
Table 3-16 LEDs ............................................................................................................................ 23
Table 3-17 VCOM Function of Nu-Link2-Me.................................................................................. 23
Table 3-18 Operation Status LED Patterns ................................................................................... 24

NuMaker-NUC029L
Dec. 26, 2022 Page 7of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
1 OVERVIEW
The NuMaker-NUC029L is an evaluation board for Nuvoton NuMicro NUC029LAN, NUC029NAN,
NUC029ZAN and NUC029TAN microcontrollers. The NuMaker-NUC029L consists of two parts: an
NUC029 target board and an on-board Nu-Link2-Me debugger and programmer. The NuMaker-
NUC029L is designed for project evaluation, prototype development and validation with power
consumption monitoring function.
The NUC029 target board is based on NuMicro NUC029LAN. For the development flexibility, the
NUC029 target board provides the extension connectors, the Arduino UNO compatible headers and the
capability of adopting multiple power supplies. Furthermore, the Nuvoton-designed ammeter connector
can measure the power consumption instantly, which is essential for the prototype evaluation.
In addition, there is an attached on-board debugger and programmer “Nu-Link2-Me”. The Nu-Link2-Me
supports on-chip debugging, online and offline ICP programming via SWD interface. The Nu-Link2-Me
supports virtual COM (VCOM) port for printing debug messages on PC. Besides, the programming
status could be shown on the built-in LEDs. Lastly, the Nu-Link2-Me could be detached from the
evaluation board and become a stand-alone mass production programmer.
Figure 1-1 NuMaker-NUC029L Evaluation Board

NuMaker-NUC029L
Dec. 26, 2022 Page 8of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
2 FEATURES
NuMicro NUC029LAN used as main microcontroller with function compatible with:
–NUC029LAN
–NUC029NAN
–NUC029ZAN
–NUC029TAN
NUC029LAN full pins extension connectors
Arduino UNO compatible extension connectors
Ammeter connector for measuring the microcontroller’s power consumption
Flexible board power supply:
–External VDD power connector
–Arduino UNO compatible extension connector Vin
–USB PWR connector on NUC029 target board
–ICE USB connector on Nu-Link2-Me
On-board Nu-Link2-Me debugger and programmer:
–Debug through SWD interface
–Online/offline programming
–Virtual COM port function

NuMaker-NUC029L
Dec. 26, 2022 Page 9of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
3 HARDWARE CONFIGURATION
3.1 Front View
ICE USB Connector
VCOM Switch
Reset Button
ICE Status LED
Off-line Program Button
USB PWR Connector
Power LED
P3.6 LED
VDD Switch
NUC029LAN NUC029LAN Extension Connectors
Arduino UNO Compatible Extension Connectors
External VDD Connector
Nu-Link2-Me
Ammeter
ICE Chip: M48SSIDAE
External VSS Connector
NUC029 Target Board
Figure 3-1 Front View of NuMaker-NUC029L
Figure 3-1 shows the main components and connectors from the front side of NuMaker-NUC029L. The
following lists components and connectors from the front view:
Target chip: NUC029LAN (U1)
USB PWR Connector (J2)
Arduino UNO Compatible Extension Connectors (NU1, NU2, NU3, NU4)
NUC029L Extension Connectors (JP3, JP4, JP5 and JP6)
External VDD Power Connector (JP1)
External VSS Power Connector (JP2)
VDD Switch (SW2)
Ammeter Connector (AMMETER)
Reset Button (SW1)
Power LED and P3.6 LED (LEDG1 and LEDR1)
Nu-Link2-Me
–VCOM Switch
–ICE Chip: M48SSIDAE (ICEU2)
–ICE USB Connector (ICEJ3)
–ICE Status LED (ICES0, ICES1, ICES2, ICES3)
–Off-line Program Button (ICESW1)

NuMaker-NUC029L
Dec. 26, 2022 Page 10 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
3.2 Rear View
Figure 3-2 shows the main components and connectors from the rear side of NuMaker-NUC029L.
The following lists components and connectors from the rear view:
Nu-Link2-Me
–MCUVCC Power Switch (ICEJPR1)
–ICEVCC Power Switch (ICEJPR2)
ICEVCC Power Switch
MCUVCC Power Switch
Figure 3-2 Rear View of NuMaker-NUC029L

NuMaker-NUC029L
Dec. 26, 2022 Page 11 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
3.3 Extension Connectors
Table 3-1 presents the extension connectors.
Connector
Description
JP3, JP4, JP5 and JP6
Full pins extension connectors on the NuMaker-NUC029L.
NU1, NU2, NU3 and
NU4
Arduino UNO compatible pins on the NuMaker-NUC029L.
Table 3-1 Extension Connectors
3.3.1 Pin Assignment for Extension Connectors
The NuMaker-NUC029L provides the NUC029LAN onboard and extension connectors (JP3, JP4, JP5
and JP6). Figure 3-3 shows the NUC029LAN extension connectors.
JP3
Pin1 ~ Pin12
JP6
Pin37 ~ Pin48
JP5 Pin13 ~ Pin24
JP4 Pin25 ~ Pin36
Figure 3-3 NUC029LAN Extension Connectors

NuMaker-NUC029L
Dec. 26, 2022 Page 12 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
Header
NUC029LAN
Pin No.
Function
JP3
JP3.1
1
P1.5 / AIN5 / ACMP0_P / MOSI_0
JP3.2
2
P1.6 / AIN6 / MISO_0 / ACMP2_N
JP3.3
3
P1.7 / AIN7 / SPICLK0 / ACMP2_P
JP3.4
4
nRST
JP3.5
5
P3.0 / UART0_RXD / ACMP1_N
JP3.6
6
AVSS
JP3.7
7
P3.1 / UART0_TXD / ACMP1_P
JP3.8
8
P3.2 / nINT0 / STADC / T0EX
JP3.9
9
P3.3 / nINT1 / MCLK / TIEX
JP3.10
10
P3.4 / T0 / SDA0
JP3.11
11
P3.5 / T1 / SCL0 / CKO
JP3.12
12
P4.3 / PWM3
JP5
JP5.1
13
P3.6 / CKO / ACMP0_O / nWR
JP5.2
14
P3.7 / nRD
JP5.3
15
XTAL2
JP5.4
16
XTAL1
JP5.5
17
VSS
JP5.6
18
LDO_CAP
JP5.7
19
P2.0 / AD8 / PWM0
JP5.8
20
P2.1 / AD9 / PWM1
JP5.9
21
P2.2 / PWM2 / AD10
JP5.10
22
P2.3 / PWM3 / AD11
JP5.11
23
P2.4 / PWM4 / SCL1 / AD12
JP5.12
24
P4.0 / PWM0 / T2EX
JP4
JP4.1
25
P2.5 / PWM5 / SDA1 / AD13
JP4.2
26
P2.6 / PWM6 / ACMP1_O / AD14
JP4.3
27
P2.7 / AD15 / PWM7
JP4.4
28
P4.4 / nCS / SCL1
JP4.5
29
P4.5 / ALE / SDA1
JP4.6
30
P4.6 / ICE_CLK
JP4.7
31
P4.7 / ICE_DAT
JP4.8
32
P0.7 / SPICLK1 / AD7
JP4.9
33
P0.6 / MISO_1 / AD6
JP4.10
34
P0.5 / MOSI_1 / AD5
JP4.11
35
P0.4 / SPISS1 / AD4

NuMaker-NUC029L
Dec. 26, 2022 Page 13 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
Header
NUC029LAN
Pin No.
Function
JP4.12
36
P4.1 / PWM1 / T3EX
JP6
JP6.1
37
P0.3 / AD3 / RTS0 / UART0_RXD
JP6.2
38
P0.2 / AD2 / CTS0 / UART0_TXD
JP6.3
39
P0.1 / RTS1 / RXD1 / ACMP3_N / AD1
JP6.4
40
P0.0 / CTS1 / TXD1 / ACMP3_P / AD0
JP6.5
41
VDD
JP6.6
42
AVDD
JP6.7
43
P1.0 / AIN0 / T2 / nWRL
JP6.8
44
P1.1 / AIN1 / T3 / nWRH
JP6.9
45
P1.2 / AIN2 / UART1_RXD1
JP6.10
46
P1.3 / AIN3 / UART1_TXD1
JP6.11
47
P1.4 / AIN4 / ACMP0_N / SPISS0
JP6.12
48
P4.2 / PWM2
Table 3-2 NUC029LAN Full-pin Extension Connectors and GPIO Function List

NuMaker-NUC029L
Dec. 26, 2022 Page 14 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
3.3.2 Arduino UNO Compatible Extension Connectors
Figure 3-4 shows the Arduino UNO compatible extension connectors.
MISO CLK RESET SS
P1.6 P1.7 nRESET P1.4
5V MOSI GND -
VDD P1.5 VSS P2.0
PWM0 P4.0 D8
PWM1 P4.1 D9
SPI1_SS P0.4 D10
SPI1_MOSI P0.5 D11
SPI1_MISO P0.6 D12
SPI1_CLK P0.7 D13
GND VSS
AVDD VREF
I2C0_SDA P3.4 SDA
I2C0_SCL P3.5 SCL
UART1_RXD P0.1 D0
UART1_TXD P0.0 D1
PWM2 P4.2 D2
PWM3 P4.3 D3
PWM4 P2.4 D4
PWM5 P2.5 D5
PWM6 P2.6 D6
PWM7 P2.7 D7
VIN
VSS
VSS
5V
3V
RST
VDD
NC
A5/SCL P4.4 I2C1_SCL
A4/SDA P4.5 I2C1_SDA
A3 P1.3 ADC3
A2 P1.2 ADC2
A1 P1.1 ADC1
A0 P1.0 ADC0
Figure 3-4 Arduino UNO Compatible Extension Connectors

NuMaker-NUC029L
Dec. 26, 2022 Page 15 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
Header
NuMaker-NUC029L
Header
NuMaker-NUC029L
Compatible to
Arduino UNO
GPIO Pin of
NUC029
Compatible to
Arduino UNO
GPIO Pin of
NUC029
NU3
NU3.1
D0
P0.1
NU2
NU2.6
A5
P4.4
NU3.2
D1
P0.0
NU2.5
A4
P4.5
NU3.3
D2
P4.2
NU2.4
A3
P1.3
NU3.4
D3
P4.3
NU2.3
A2
P1.2
NU3.5
D4
P2.4
NU2.2
A1
P1.1
NU3.6
D5
P2.5
NU2.1
A0
P1.0
NU3.7
D6
P2.6
NU1
NU1.8
VIN
-
NU3.8
D7
P2.7
NU1.7
VSS
NU4
NU4.1
D8
P4.0
NU1.6
VSS
NU4.2
D9
P4.1
NU1.5
5V
NU4.3
D10
P0.4
NU1.4
3V
NU4.4
D11
P0.5
NU1.3
RST
nRESET
NU4.5
D12
P0.6
NU1.2
VDD
VDD
NU4.6
D13
P0.7
NU1.1
NC
-
NU4.7
VSS
VSS
NU4.8
VREF
AVDD
NU4.9
SDA
P3.4
NU4.10
SCL
P3.5
Table 3-3 Arduino UNO Extension Connectors and NUC029LAN Mapping GPIO List

NuMaker-NUC029L
Dec. 26, 2022 Page 16 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
3.4 Power Supply Configuration
The NuMaker-NUC029L is able to adopt multiple power supplies. External power sources include NU1
Vin (7 V to 12 V), VDD (depending on the target chip operating voltage), and PC through USB connector.
By using switches and voltage regulator, multiple power domains can be created on the NuMaker-
NUC029L.
3.4.1 VIN Power Source
Table 3-4 presents the Vin power source.
Connector
Net Name in
Schematic
Description
NU1 pin8
NU1_VIN
Board external power source, with voltage range from 7
V to 12 V. The voltage regulator UP2 converts the NU1
pin8 input voltage to 5 V and supplies it to NU1_5VCC.
Table 3-4 Vin Power Source
3.4.2 5 V Power Sources
Table 3-5 presents the 5 V power sources.
Connector
Net Name in
Schematic
Description
ICEJ3
USB_HS_VBUS
ICE USB connector supplies 5 V power from PC to
NUC029 target board and Nu-Link2-Me.
J2
USB_VBUS
USB connector on NuMaker-NUC029L supplies 5 V
power from PC to NUC029 target board and Nu-Link2-
Me.
NU1 pin5
NU1_5VCC
ICEJ3, J2 or NU1 pin8 supplies 5 V power to NU1 pin5.
NU1 pin5 supplies 5 V power to target chip or Arduino
adapter board.
Table 3-5 5 V Power Sources

NuMaker-NUC029L
Dec. 26, 2022 Page 17 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
3.4.3 3.3 V Power Sources
Table 3-6 presents the 3.3 V power sources.
Voltage
Regulator
5 V Source
Description
ICEUP1
USB_HS_VBUS
ICEUP1 converts USB_HS_VBUS to 3.3 V and
supplies 3.3 V to NUC029 target board or ICE chip.
UP1
USB_VBUS
UP1 converts USB_VBUS to 3.3 V and supplies 3.3 V
to NUC029 target board.
Note: SW2.2 (NU1 3VCC) should be switched to ON.
UP1
NU1_5VCC
UP1 converts NU1_5VCC to 3.3 V and supplies 3.3 V
to NUC029 target board.
Note: SW2.2 (NU1 3VCC) should be switched to ON.
Table 3-6 3.3 V Power Sources
3.4.4 1.8 V Power Sources
Table 3-7 presents the 1.8 V power source.
Voltage Regular
5V Source
Description
ICEUP2
USB_HS_VBUS
ICEUP2 converts USB_HS_VBUS to 1.8 V and
supplies 1.8 V to NUC029 target board or ICE chip.
Table 3-7 1.8 V Power Sources
3.4.5 Power Connectors
Table 3-8 presents the power connectors.
Connector
Description
JP1
VDD connector on the NuMaker-NUC029L.
JP2
VSS connector on the NuMaker-NUC029L.
Table 3-8 Power Connectors

NuMaker-NUC029L
Dec. 26, 2022 Page 18 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
3.4.6 USB Connectors
Table 3-9 presents the USB connectors.
Connector
Description
ICEJ3
ICE USB connector on Nu-Link2-Me for power supply, debugging and
programming from PC.
J2
USB PWR connector on NuMaker-NUC029L for power supply.
Table 3-9 USB Connectors
3.4.7 Power Switches
Table 3-10 presents the power switches.
Switch
Description
ICEJPR1
Configures the target chip operating voltage at 1.8 V / 3.3 V / 5 V.
ICEJPR2
Configures the ICE chip operating voltage at 1.8 V / 3.3 V.
SW2
Configures the target chip operating voltage at 3.3 V / 5 V.
Table 3-10 Power Switches
3.4.8 Power Supply Models
External Power Supply through Nu-Link2-Me to Target Chip
The external power supply source on Nu-Link2-Me is shown in Figure 3-5.
ICE USB Connector (ICEJ3)
Nu-Link2-Me
Figure 3-5 External Power Supply Sources on Nu-Link2-Me
To use ICEJ3 as external power supply source with Nu-Link2-Me, please follow the steps below:
1. Solder the resistor on ICEJPR1 (MCUVCC) depending on the target chip operating voltage.

NuMaker-NUC029L
Dec. 26, 2022 Page 19 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
2. Solder the resistor on ICEJPR2 (ICEVCC) depending on the ICE chip operating voltage.
3. Switch the SW2 to OFF.
4. Connect the external power supply to ICEJ3.
Table 3-11 presents all power models when supplying external power through Nu-Link2-Me. The Nu-
Link2-Me external power sources are highlighted in yellow.
Model
Target
Chip
Voltage
ICEJ3
ICEJPR1
(MCUVCC)
Selection [1]
ICEJPR2
(ICEVCC)
Selection [2]
ICE
Chip
Voltage
SW2
Selection
J2
Vin
JP1
1
1.8 V
Connect
to PC
1.8 V
1.8 V
1.8 V
Off
-
-
1.8 V
output
2
3.3 V
Connect
to PC
3.3 V (default)
3.3 V
(default)
3.3 V
Off
-
-
3.3 V
output
3
5 V
Connect
to PC
5 V
3.3 V
(default)
3.3 V
Off
-
-
5 V
output
Note:
1. 0 Ω should be soldered between ICEJPR1’s MCUVCC and 1.8 V / 3.3 V / 5 V.
2. 0 Ω should be soldered between ICEJPR2’s ICEVCC and 1.8 V / 3.3 V.
3. -: Unused.
Table 3-11 Supply External Power through Nu-Link2-Me
External Power Supply through NUC029 Target Board to Target Chip
The external power supply sources on NUC029 target board are shown in Figure 3-6.
USB Power Connector (J2)
NU1 pin8 (Vin)
External VDD Connector (JP1)
External VSS Connector (JP2)
Figure 3-6 External Power Supply Sources on NUC029 Target Board
To use Vin or J2 as external power supply source, please follow the steps below:
1. Switch the SW2 depending on the target chip operating voltage.
2. Remove the resistor on ICEJPR1 (MCUVCC).
3. Solder the resistor on ICEJPR2 (ICEVCC) depending on the ICE chip operating voltage.
4. Connect the external power supply to Vin or J2.
To use JP1 as external power supply source, please follow the steps below:
Switch the SW2 to OFF.

NuMaker-NUC029L
Dec. 26, 2022 Page 20 of 46 Rev 1.00
NUMAKER-NUC029L USER MANUAL Maker Nu-mbed NUC472 User Manual
2. Remove the resistor on ICEJPR1 (MCUVCC).
3. Solder the resistor on ICEJPR2 (ICEVCC) depending on the ICE chip operating voltage.
4. Connect ICEJ3 to PC.
5. Connect the external power supply to JP1.
To use Vin or J2 as external power supply source with Nu-Link2-Me detached from NuMaker-
NUC029L, please follow the steps below:
Switch the SW2 depending on the target chip operating voltage.
2. Detach the Nu-Link2-Me from NuMaker-NUC029L.
3. Connect the external power supply to Vin or J2.
To use JP1 as external power supply source with Nu-Link2-Me detached from NuMaker-
NUC029L, please follow the steps below:
Switch the SW2 to OFF.
2. Detach the Nu-Link2-Me from NuMaker-NUC029L.
3. Connect the external power supply to JP1.
USB Power Connector (J2)
NU1 pin8 (Vin)
External VDD Connector (JP1)
External VSS Connector (JP2) Detach Nu-Link2-Me
"
"
Figure 3-7 Detach the Nu-Link2-Me from NuMaker-NUC029L