NuWaves NUPOWER C30R01 User manual

USER MANUAL
NUPOWERTM C30R01
C-BAND POWER AMPLIFIER
PART NUMBER:
NW-PA-C-30-R01
NuWaves Engineering
132 Edison Drive
Middletown, Ohio 45044
PH: 513-360-0800
FAX: [phone]
www.nuwaves.com
[e-mail]

NuPower
TM
C30R01 User Manual
Rev 1.0
1
1NUPOWERTM PRODUCT LINE OVERVIEW
The NuPower family of solid-state RF power amplifier (PA) modules is designed to meet the demanding
needs of the Aerospace & Defense, Industrial, and Commercial markets. Based on the latest gallium nitride
(GaN) technology, NuPower’s power efficiency and miniature form factor make it ideal for size, weight,
and power-constrained broadband RF telemetry and tactical communications systems.
1.1 NUPOWERTM PRODUCT LINE HIGHLIGHTS
•High Performance: Unique combination of broadband coverage, miniature form factors, and high
efficiency.
•Enclosures: The NuPower family of power amplifiers is housed in a silver nickel plated aluminum
enclosure with mounting holes incorporated into the chassis.
•Completely Characterized: The NuPower family of solid-state power amplifiers has been
completely characterized over temperature, voltage, and frequency. These high-performance
modules offer significant value for the OEM user or the Systems Integrator.
•User Friendly: Over-Voltage protection and regulator thermal shutdown provide defenses against
user interface issues.
•High Reliability: NuWaves’ selection of conservatively rated components provides high reliability.
Each NuPower is inspected to IPC-A-610 Class II quality standards. NuWaves’ Quality Management
System is AS9100:2016 Rev D and ISO 9001:2015 certified.
•Applications: Broadband RF Telemetry •RF Communication Systems •Electronic Warfare •
Unmanned Aircraft Systems (UAS) •Unmanned Ground Vehicles (UGV) •Unmanned Surface
Vehicles (USV) •Software Defined Radios • Test Labs
•Available Options:
oFan-cooled heat sink with 28V operated fan
oLabeled interface cable with banana jack plugs

NuPower
TM
C30R01 User Manual
Rev 1.0
2
2NUPOWERTM C30R01 PA OVERVIEW
The NuPowerTM C30R01 PA is a highly efficient, solid state power amplifier that provides over 30 watts of
RF power across 5030 - 5090 MHz.
Based on the latest gallium nitride (GaN) technology, NuPower L-Band power efficiency and < 10 in3 cubic
inch form factor make it ideal for size, weight, and power-constrained broadband RF telemetry and tactical
communication systems.
The NuPowerTM C30R01 ruggedized chassis allows the system integrator to easily incorporate the unit into
a platform operating in harsh environments with limited space, such as small Unmanned Aircraft Systems
(UAS).
Figure 1: NuPower C30R01 Functional Diagram

NuPower
TM
C30R01 User Manual
Rev 1.0
3
2.1 NUPOWER C30R01 PA SPECIFICATIONS
The subsequent tables in this section outline the NuPower C30R01’s performance specifications.
Table 1: NuPower C30R01 Electrical Specifications
Parameter Specification
Frequency Range 5030 to 5090 MHz
RF Output Power 30 Watts (min)
Output Power @ 1 dB Compression
28 dBm @ 5030 MHz
29 dBm @ 5060 MHz
29 dBm @ 5090 MHz
RF Gain 45 dB
Input VSWR 2.3 (typ)
Output Mismatch
(No Damage) 10:1
Nominal Input Drive Level 0 dBm
Maximum Input Drive Level
(No damage) +15 dBm
Harmonic
2nd: ≤-70 dBc
3rd: ≤-70 dBc
Third Order Intercept Point
(Two tone test at 1 MHz spacing,
Pout = 20 dBm / tone)
40 dBm @ 5.03 GHz
Switching Speed 2 µS
Operating Voltage +27 to +30 VDC
Operating Current 4.1 A @ +28 VDC (typ)
Module Efficiency 30%
Power Amplifier Enable RF Enable Grounded
Impedance 50 Ω

NuPower
TM
C30R01 User Manual
Rev 1.0
4
Table 2: NuPower C30R01 Environmental Specifications
Operating Conditions Specification
Operating Temperature -40 to +55 oC (ambient)
-40 to +85 oC (baseplate)
Storage Temperature -55 to +85 oC
2.2 NUPOWER C30R01 PA MECHANICAL SPECIFICATIONS
Figure 2: NuPower C30R01 Mechanical Outline
Table 3: NuPower C30R01 Mechanical Specifications
Parameter Specification
RF Connectors SMA (female)
Control / Power Interface Connector 9 Pin Micro-D (socket)
Dimensions (L x W x H) 4.5” x 3.5” x 0.61”
Weight 9 oz.

NuPower
TM
C30R01 User Manual
Rev 1.0
5
2.3 HEAT SINKING
The NuPower C30R01 is offered as a stand-alone module or with an accessory kit
(P/N: NW-PA-ACC-KT03), which includes a 28 VDC fan-cooled heatsink and requisite power cable. [The kit
also includes an upgraded module interface cable assembly, labeled and terminated with banana plugs.]
Figure 3: The NuPower PA Kit offers “out-of-the-box” operation for the user. The 28 VDC fan-cooled
heatsink is shown with the NuPower C30R01 mounted.
Caution: The use of external heat-sinking is required especially for those applications
requiring high duty cycle operation (e.g. continuous wave) or for extended on-time
testing.
Operation without a proper heat sink under these conditions will cause
permanent damage to the product and will void the product warranty.
The max operating temperature is 85˚ C (baseplate).

NuPower
TM
C30R01 User Manual
Rev 1.0
6
3SETUP AND OPERATION
This section provides specific details for proper operation of the NuPower C30R01 module. Following
these guidelines will prevent damage to the power amplifier or external equipment.
3.1 POWER SUPPLY REQUIREMENTS
To operate the NuPower C30R01, ensure that the power supply has adequate overhead to source the
current demand of the RF power amplifier. The power supply source must provide a typical voltage of +28
VDC with greater than 6 amps capability.
3.2 CONNECTING A PROPER LOAD TO THE ANTENNA TERMINAL
To prevent damage to the PA, the antenna terminal must be terminated into a 50 Ωload. Examples of a
proper load include:
•Directly connecting to an antenna specified for the frequency range (5030 MHz to 5090 MHz).
Connecting to an inappropriate antenna may result in damage to the PA module.
•Connecting to a proper antenna through a 50 Ωtransmission line or coaxial cable. Avoid using
damaged cables or corroded connectors while attaching the unit to an antenna.
•Terminating the antenna terminal into a 50 Ωpower attenuator with minimum 20 dB attenuation.
•Connecting to a load capable of dissipating the RF power from the PA module. Loads capable of
handling 50 Watts (min) are recommended.
3.3 POWERING-UP THE NUPOWER C30R01
The NuPower C30R01 must be terminated to a proper load before power is applied. Refer to Section 3.2
for the specifications of the proper load. After the PA is properly terminated, the interface cable can be
connected to the unit and power can be applied. The PA is now ready for operation.
3.4 TRANSMIT TURN-ON TIME
Caution: Do not apply transmit data until the PA module is at full power. This will prevent
loss of data at the beginning of a message.
The NuPower C30R01 is at full power approximately 1 µS after the RF Enable line goes low (ground).
Therefore, transmit data can be applied to the input after 1 µS without loss of data.
3.5 RF OUTPUT POWER VS. SUPPLY VOLTAGE
The NuPower C30R01 was designed for +28 VDC operation.

NuPower
TM
C30R01 User Manual
Rev 1.0
7

NuPower
TM
C30R01 User Manual
Rev 1.0
8
4HARDWARE INTERFACE
•The RF Input connector is SMA (female).
•The RF Output connector is SMA (female).
•The pin-out definitions for the 9 pin Micro-D socket connector are provided in Table 5. In a typical
installation, the PA module is mated to a host controller board via a cable harness.
The RF Out SMA connector is the antenna connection. This connection should always
be loaded into 50 Ω, otherwise the PA could be damaged.
4.1 INTERFACE CABLE HARNESS
The cable harness that connects the host controller to the 9 pin Micro-D connector of the NuPower
C30R01 is made up of 9 wires.
Table 4: NuPower C30R01 Interface Pin-Out Definitions
Pin No. Pin Name I/0 Description
3, 4, 5 V Supply I Primary Power (+28 VDC)
1, 2, 6, 8 GND I Signal and Power Ground
7 Temp Flag 0 Over-temp Indicator
0V = temperature fault
+5V = no fault
9 RF Enable I Transmit Control
0V or GND = RF On
+5V or NC = RF Off
Figure 4: Micro-D Socket Locations

NuPower
TM
C30R01 User Manual
Rev 1.0
9
4.2 DC POWER
The nominal supply voltage for the NuPower C30R01 is +28 VDC; The acceptable supply voltage range is
+27 to +30 VDC.
4.3 GROUND
The signal and power grounds are tied together in the PA module.
4.4 RF ENABLE
This signal is the logic control input that designates whether the unit is in transmit or standby mode. The
RF Enable line is pulled high internally placing the PA module in standby mode. If the pin is left floating
(i.e. not connected), the unit will default to standby mode.
Grounding the pin (i.e. a voltage below +0.2 VDC) places the unit in transmit mode. The user can either
connect the RF Enable line to pins, 1, 2, 6 & 8 on the CTRL/PWR interface connector, or an open drain
logic line capable of sinking 500 µA to place the unit in transmit mode.
4.5 TEMP FLAG
This signal is an output to indicate an over-temperature condition in the NuPower C30R01. A logic high
(+5 VDC) indicates normal operation, while a logic low (0 VDC) indicates an over-temperature condition.
The NuPower C30R01 incorporates internal logic circuitry that turns off the DC bias to the RF transistors.
Caution: The amplifier should be shut down and allowed to cool off when the over-
temperature flag is set low to avoid damage to the module.

NuPower
TM
C30R01 User Manual
Rev 1.0
10
5PRODUCT DISPOSAL – END-OF-LIFE
Safety is a guiding principle of NuWaves Engineering. We ensure safe production and operation of our
products, as well as end-of-life disposal. Improper disposal can adversely affect the environment, wildlife
and human health. Please follow these guidelines when disposing of a NuWaves product:
•Do not remove the cover or any hardware
•Do not remove components from the circuit card assembly
•Do not incinerate
•Do not crush or shred
•Do not dispose of as unsorted municipal waste
•Do not export e-waste outside of the original destination country for recycling
•Utilize an e-Steward or ISO14001 certified e-waste recycler
•Consider export controls during recycler selection
•If a NuWaves product is incorporated into a larger system or sub-system, ensure that these
guidelines are followed at system end-of-life

NuPower
TM
C30R01 User Manual
Rev 1.0
11
6GETTING HELP - APPLICATIONS ENGINEERING
NuWaves Engineering offers technical support for basic configuration help and troubleshooting, Monday
through Friday, 8 a.m. to 5 p.m. Eastern Time.
Technical Assistance, Application Engineering and Sales:
Phone: [phone]
Email: [e-mail]
NuWaves Home Page: https://www.nuwaves.com/
Product Warranty:
https://nuwaves.com/wp-content/uploads/NuWaves_Warranty_Repair.pdf
6.1 GENERAL INFORMATION
Copyright © 2006 – 2019 NuWaves Ltd. All rights reserved. The information contained in this user manual
is copyright protected. NuWaves reserves the right to make periodic modifications and product
improvements to the NuPower product line and the associated documentation.