Nyrius ORION HOME TB52 User manual

QUICK START GUIDE v 1.2 ORION HOME (TB52)
www.nyrius.com

2
Thank you for your purchase of
this Nyrius product. We hope you
enjoy your experience. If you have
any questions please visit us at
www.nyrius.com/support
Since its inception Nyrius has been
a leader in developing innovative
connectivity solutions. Our
products have been enchanting
home entertainment enthusiasts
and business professionals
through exceptional product
design, high performance, and
outstanding customer service. At
Nyrius, our mission is a simple one
– create people-driven products
that make life easier and more
WHAT’S INCLUDED
Receiver Power Adapter x 2 HDMI Cable x 2 Antennas X 4
Transmitter IR Emitter IR Receiver
Quick Start Guide Lifetime Customer
Support
1 Year Warranty
LIFETIME
CUSTOMER
SUPPORT

3
FIRST TIME SETUP
1
Connect the power adapter to the Receiver. Connect Receiver and TV with
HDMI cable. Select the correct video input/source on the TV.
2
HDMI
HDMI
HDMI POWER
RECEIVER
Note: The initial connection can take up to 45 seconds. Ensure the units
are given enough time to establish connection on first use.
3Connect the power adapter to the Transmitter. Connect an HDMI cable to
the video source device and connect the other end of the HDMI cable to
the Transmitter’s HDMI input. Once connected the status LED will turn
blue.
DC 5V SERVICE RESET HDMI OUT HDMI OUTHDMI IN IR OUT
HDMI HDMI
HDMI
TRANSMITTER DEVICE
POWER
Connect the 2 antennas to the Transmitter and 2 antennas to the Receiver.

4
The Orion Home supports up to a maximum of 2 receivers. Additional receivers
are available on www.nyrius.com
To connect a second receiver, ensure your transmitter is connected to the
video source and powered on. Then connect your second receiver to a TV and
power source. The receiver will automatically connect to the closest available
transmitter.
OPTIONAL: CONNECTING MULTIPLE RECEIVERS
RESETTING CONNECTION
If you are experiencing connectivity issues, press the RESET button on the
Transmitter or Receiver.
DC 5V SERVICE RESET HDMI OUT IR IN DC 5V SERVICE RESET HDMI OUT
HDMI IN IR OUT
RECEIVER RESETTRANSMITTER RESET
OPTIONAL: CONNECT THE TRANSMITTER TO A TV WITH AN HDMI CABLE
DC 5V SERVICER ESET HDMI OUT
HDMI IN IR OUT HDMI
HDMI
HDMI OUT

5
IR EXTENDER SETUP
IR Extender Setup Video available at www.nyrius.com/resources
What is an IRExtender Cable?
The Orion Home comes with an IR Receiver and IR Emitter that allow you
to control your source device with its remote from the Receiver’s location.
The remote’s IR signal is transmitted by the Receiver to the Transmitter
and then through the IR Emitter to the source device.
Plug the IR Receiver into the back of the Receiver.
1
Place the IR Receiver bubble in a visible location so it can receive the
remote control signal.
2
HDMI
DC 5V SERVICE RESET HDMI OUT IR IN
IR RECEIVER RECEIVER

6
Plug the IR Emitter into the back of the Transmitter.
3
TRANSMITTER IR EMITTER
DC 5V SERVICE RESET HDMI OUT
HDMI IN IR OUT
Place the IR Emitter in front of the IR sensor on your video source
device (Cable Box, Blu-ray Player).
Note: For help on locating the IR sensor see instructions on
following pages.
4
TRANSMITTER
IR EMITTER
DC 5V SERVICE RESET HDMI OUT
HDMI IN IR OUT
DEVICE
Point the source device’s remote control at the IR Receiver that is
connected to the Nyrius Receiver. The source device should receive
the signal.
5
HDMI
RECEIVER TRANSMITTER

7
LOCATING THE IR SENSOR ON THE SOURCE DEVICE
Cut a piece of cardboard to the size as the front panel of the source
device. Cut a 1 inch hole in the center of the cardboard.
1
DEVICE
Power on the source device and play a movie or other video content.
Place the cardboard hole over the left side of the source device and place
the remote control directly in front of the hole.
2
DEVICE
Press the pause button on the remote control repeatedly while gradually
moving the cardboard hole from left to right. Once the source device
recognizes the pause button you have located the sensor location.
Press the pause button on the remote control repeatedly while gradually
moving the cardboard hole from left to right. Once the source device
recognizes the pause button you have located the sensor location.
3
DEVICE

8
TROUBLESHOOTING
If your remote control is not controlling your video source such as changing the
channel, we would recommend the following troubleshooting.
1. Confirm there are new batteries in the remote control.
2. Check the IR Emitter and IR Transmitter connections on Orion.
3. Check the IR Emitter is directed towards the IR sensor on your device.
Try moving the emitter to different positions around the sensor.
You can confirm that the IR Receiver and the IR Emitter are transmitting the IR
signal using a smartphone camera. While IR signals are invisible to the human
eye, you will see LED flashing when you watch it through your smartphone
For additional assistance please contact our us at www.nyrius.com/support
1. What do the LEDs mean?
Flashing Blue – Not Connected
Solid Blue – Connected
2. What is the maximum transmission range?
The maximum range is 300 feet line of sight. If transmitting through walls, ceilings,
from cordless phones, wireless routers, or other sources of interference.
3. What steps can I take if the IR Extender is not working?
Ensure that the remote control you are using is an IR remote control. The supported
IR sensor on your device. If you are unsure of the location please contact the
manufacturer of your HDMI enabled product.
4. The Orion Home appears warm after prolonged use.
To transmit HD content wirelessly, the Orion Home must process a large amount of
data. Due to this, the unit may run at warmer temperatures than other electronic
devices. We have designed the housing to provide proper ventilation to the unit as
well as have designed the electronic components to withstand temperatures up to
80°C. To ensure maximum performance ensure both the Transmitter and Receiver
are in well ventilated areas that do not exceed 30°C.
FREQUENTLY ASKED QUESTIONS
Aim the remote at the IR Receiver connected to the TB52 Receiver.
Position the camera in front of the IR Emitter connected to the
TB52 Transmitter.
Press a button on the remote control and check the digital camera’s
screen/footage to see the LED flash from the IR Emitter.
If you don’t see a flash check all connections and confirm the remote is an
IR remote control and uses a frequency between 20-60KHz.
1.
2.
3.
4.

9
5. What are the troubleshooting steps if no video is displayed?
The Transmitter/Receiver may require a few seconds to connect. Ensure the correct
HDMI video input is selected on your TV and that your HDMI cables are connected
properly. Check that your video resolution from the source device is set to 1080p,
1080i, 720p, 576p, or 480p. Please ensure the Orion Home is not located near a
wireless access point as interference may affect connectivity.
6. Does this device support multiple receivers and transmitters?
The Orion Home supports up to two receivers connected at one time but can only be
connected to one transmitter. Additional receivers are available at
www.nyrius.com. It is not recommended to use more than one set of transmitters
and receivers in the same environment as receivers will always connect to the
strongest transmitter signal.
7. Why is there a delay between the Receiver TV and the Video Source?
The Orion Home has less than 200ms of latency. This means that the transmitted
image showing on the Receiver will be slightly behind the source device. This means
that the Orion Home is best suited for viewing media. If used with computers or
gaming consoles there may be a slight delay with mouse/controller input.
8. Whatis the purpose of the Service port on the Receiver?
The Service port is intended for internaluse only. It should only be used by
official service personnel.
FCC WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
FCC CAUTION:
the user’s authority to operate this equipment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. For operation with 5150 - 5250GHz (5470-5725GHz
frequency range, it is restricted to indoor environment. The band from 5600-5650MHz will be disabled
by the software during the manufacturing and cannot be changed by end user. This device meets all the
RADIATION EXPOSURE STATEMENT (TRANSMITTER):
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment
and are safe for intended operation as described in this manual. The further RF exposure reduction can
be achieved if the product can be kept as far as possible from the user body or set the device to lower
output power if such function is available. The USB dongle transmitter is approved for use in typical
laptop computers. To comply with FCC RF exposure requirements, it should not be used in other devices
users or bystanders to satisfy RF exposure compliance requirements. Receiver should be installed and
operated with minimum distance 20cm between the radiator & your body.

10
RADIATION EXPOSURE STATEMENT (RECEIVER):
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Note: The country code selection is for non-US model only and is not available to all US model. Per FCC
IC STATEMENT
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted
for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still
complies with the e.i.r.p. limit; (iii) the maximum antenna gain permitted for devices in the band 5725-
to-point and non-point-to-point operation as appropriate; and (iv) Users should also be advised that
high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and
5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
RADIATION EXPOSURE STATEMENT:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
AVERTISSEMENT:
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les
restrictions susmentionnées, notamment: (i) les dispositifs fonctionnant dans la bande 5150-5250
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal
d’antenne permis pour les dispositifs utilisant les bandes de 5250 à 5350 MHz et de 5470 à 5725 MHz doit
être conforme à la limite de la p.i.r.e; (iii) le gain maximal d’antenne permis (pour les dispositifs utilisant
point et l’exploration non point à point, selon le cas; (iv) De plus, les utilisateurs devraient aussi être avisés
que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.,qu’ils ont
la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du
brouillage et/ou des dommanges aux dispositifs LAN-EL
DÉCLARATION D’EXPOSITION AUX REDIATIONS:
Cet équipment est conforme aux limites d’exposition aux rayonnements ISED établies pour environ-
nment non contrôlé. Cet équipment doit être installé et utilisé avec un minimum de 20 cm de distance
entre la source de rayonnement et votre corps.
Thank you for choosing Nyrius! We guarantee your investment in our products is a
solid one. Our products come with a complete one-year parts and labor warranty.
High performance components combined with quality craftsmanship allow us
to maintain the highest possible production standards. All items are guaranteed
against defects in materials and craftsmanship. Nyrius has outstanding quality
control; if something should go wrong with any of our products, we will repair
it free of charge within the warranty period. If the product cannot be repaired,
we will replace the product. In the event that Nyrius replaces a product under
warranty, the replacement would only carry the original warranty from the original
date of purchase.
NYRIUS®WARRANTY