nzwardrobes Melteca Tower User manual

Melteca Tower Assembly
and Installation Guide
For nzwardrobes.co.nz Melteca Shelving Systems
Any queries, please phone [phone]

• Medium Phillips Screwdriver
TOOLS REQUIRED
PARTS INDEX
TOWER ASSEMBLY
1 2
3
6
5
7
4
1
Left Side
Carcass
2
Right Side
Carcass
Cam Screw
Top Shelf
Carcass
3
Middle Shelf
Carcass
4
Bottom Shelf
Carcass
5
Back Rail Bottom Carcass
7
Back Rail Top Carcass
6

A) Lay Panels 1 and 2 down with the holes
facing up.
B) Lay Panels 3 and 5 down with the holes
facing up and Cams facing down.
C) Screw the Cam Screws into the holes
marked with a as seen in Fig 1.
Fig. 1.
TOWER ASSEMBLY
STEP 1
1
Left Side
Carcass
21
35

STEP 3
A) Place Panels 6 and 7 onto Cam Screws
as per diagram below.
B) Tighten Cams as you go.
STEP 2
A) Place Panels 3, 4 and 5 onto Cam
Screws as per diagram below and tighten
Cams as you go.
NOTE: When tightening Cams, hold
screwdriver at an approximate 65° angle.
See Fig 2.
Edge Tape
to the front
Edge Tape
facing down
Edge Tape
facing up
FRONT VIEW
REAR VIEW
Edge Tape
to the front
Cams Facing Up
Cams facing to
the rear
Cams facing to
the rear
Cams Facing Down
Approx 65°
Cams Facing Down
1
5
4
3
3
4
5
6
7
1
Fig. 2.
Cam Screws

STEP 4
A) Place Panel 2 onto Cam Screws as
shown per diagram below.
B) Tighten Cams and re-check all Cams on
the Tower are rm.
1
FRONT VIEW
3
6
4 5
7
2

Some tools available to purchase
@ homespace.co.nz/tools
• Cordless Drill
• Medium Phillips Screwdriver
• Tape Measure
• Level
• Pencil
• 5mm Drill Bit
TOOLS REQUIRED
PARTS INDEX
INSTALLATION
A 2x 50mm Countersunk Wood Screw
B 2x 30mm Countersunk Wood Screw
C 6x Wall Anchors
D 6x 40mm Screws
E 4x Screw Cover Stickers
F Fixing Rail
G Assembled Tower
A
B
C
D
E
G
F
1 2
3
6
5
7
4
Fixing Rail

INSTALLATION
STEP 1
Locate a wall stud to secure the MDF Tower
to the wall. The Wall Stud needs to be behind
the Fixing Rail but not in the centre.
STEP 2
If you would like to use the standard 2080mm
height for the tower, the Fixing Rail will be
2064mm from the oor to the top of the
Fixing Rail.
Place the Fixing Rail onto the wall, taking care
to ensure the Fixing Rail is level. Using a screw
(D), push through the holes in the Fixing Rail to
mark the wall.
2064mm
Wall Stud
Fixing Rail
Level

STEP 3
STEP 4
Fig 1) Remove the Fixing Rail and drill
5mm holes where you have marked with the
screw.
Fig 2) Push the Wall Anchors into the
holes. (You will need to tap these in gently
with a hammer).
Using the Screws (D) provided screw the
Fixing Rail to the wall.
Wall Stud
Wall Stud
Fig 1
Fig 2

STEP 5
Using Screw (A), drill through the Fixing
Rail and into the Wall Stud.
Fig 3) Lift the Tower Unit onto the Fixing Rail.
Fig 4) Using the Screws (B), screw the Tower
to the Fixing Rail using the pre-drilled holes.
Front ProleSide Prole
STEP 6
Wall Stud
Wall
Fixing
Rail
Fig 3 Fig 4

Ensuring the Tower is level, screw Screw
(A) through Panel 7 and into the Wall Stud.
Place the Cover Stickers (E) over the
screw heads on Panels 6 and 7.
STEP 8
STEP 7
Wall StudLevel
7

Drawer Bottom
Drawer Back
Right Drawer Side
Left Drawer Side
Drawer Front
E
E
B
B
A
C
C
D
D
• Medium Phillips Screwdriver
TOOLS REQUIRED
PARTS INDEX
Drawer Assembly
Drawer Handle
Drawer Roller
Cam Screw
Draw Roller
Screw
A

DRAWER ASSEMBLY
STEP 1
STEP 2
A
Drawer Front
A
B
C
D
Fig 3
A
D
C
Edge Tape
to the front
Cam Screws
Cams facing
out
A) Lay Panel A down with the holes facing
up.
B) Lay Panels B, C and D down with the
holes facing up and Cams facing down.
C) Screw the Cam Screws into the holes
marked with a as seen in Fig 3.
A) Place Drawer Sides C and D onto Cam
Screws as per diagram below.
B) Tighten Cams as you go.
DRAWER FRONT

STEP 3
STEP 4
A) Slide Panel B up into Cam Screws as
shown in diagram below.
B) Hold Panel B up in position and tighten
Cams.
A) Push Panel E with the Cams facing
down onto the Cam Screws.
B) Tighten the Cams
A
CD
B
Cams
facing up
E
D
A

A) Place Drawer Runners as per diagram
below onto assembled Drawer.
B) Using pre-drilled holes and Drawer Roller
Screws, screw on Drawer Runners.
STEP 6
Roller facing down
and to the back
Screw the Drawer Handles to the Drawer
Front as shown in diagram below.
Re-check all the Cams on the Drawer are
rm.
STEP 7

FITTING DRAWERS AND SHELVES
A) Position the rollers facing down and to
the front onto the holes marked with an
as seen in Fig 4.
B) Screw Drawer Rollers to the Tower.
C) Push the Shelf Cams into the holes
above Panel 4 as seen in Fig 5.
Slide in Drawers and place shelves onto
Cam Screws.
STEP 1
STEP 2
1 2
3
6
5
7
4
5
7
4
Fig 4