Oasis PGN8EBF User manual

1
PGN8EBF
PGN8FEBF
Wall Mounted Refrigerated Bottle Filler
INSTALLATION INSTRUCTIONS

•Electric drill/driver
•Small tubing cutter for plastic line
• 1/4” nut driver
What’s Included:
Tools & Hardware Required:
Section 1: Getting Started
2
Drain Elbow
x2
•Means to cut 1-1/4” drain pipe
•T15 Torx screwdriver and bit
•4 appropriate anchors (not
supplied)
T15 Torx Screws
x2
Drainpipe
x2
VersaFilter III
(Included in Filtered
Model Only)

PGN8EBF:
Section 2: Single Level Rough-In Drawing
3
NOTES:
1. TRAP, STOP VALVE AND ELECTRICAL OUTLET NOT FURNISHED.
2. ALLOW 4 INCHES [102MM] MIN. PER SIDE FOR VENTILATION.
3. RECOMMENDED ADULT BARRIER FREE HEIGHT INSTALLATION SHOWN. REDUCE HEIGHT
BY 3 INCHES FOR INSTALLATIONS USED PRIMARILY BY CHILDREN AGES 12 AND YOUNGER.
UNIT SHALL ALSO HAVE A MINIMUM CLEAR FLOOR SPACE 30[760] BY 48[1220]. ADJUST
VERTICAL DIMENSIONS AS REQ’D TO COMPLY WITH FEDERAL, STATE, AND LOCAL CODES.
4. ALL DIMENSIONS ARE IN INCHES. DIMENSIONS IN BRACKETS [ ] ARE IN MILLIMETERS.
*

Section 3: Preparation
4
Read these instructions before installing the unit.
1. Inspect the carton and water cooler for evidence of rough handling and concealed
damage. Damage claims should be filed with the carrier.
2. Locate and install plumbing and electrical service, if required, in accordance with
Roughing-in Drawing. See page 3.
Note: The following states require a licensed plumber to install cooler;AR, GA,
MA, MI, OK, RI, SC, SD, TX, VT and WI. CA, KS, MN, NM and OR allow for a
state-registered installer or contractor as well. State and local plumbing codes may
prohibit the use of saddle tapping valves for water line connection in some
applications.All connections must conform to applicable plumbing codes.
3. This drinking water cooler is designed to be operated at a water supply line pressure of
up to 100 psi (690 kPa). A pressure regulator must be installed in front of unit’s water
inlet if water pressure (including any possible pressure spikes) could exceed 100 psi
(690 kPa).
4. Check available power supply against the water cooler data plate to ensure correct
electrical service. This drinking water cooler is intended to be connected to a 20A
minimum ground fault circuit interrupting (GFCI) device to meet UL requirements. The
rear most 1-3/8” diameter knockout in frame bottom is for an externally located electrical
supply. Make sure knockout hole edge is smooth and free of any burrs. Use of a Heyco
bushing #2184 in knocked out hole is recommended in order to prevent damage to
service cord and to close up excess opening around cord. Route cord so it does not
interfere with ADA space requirements.
Refer to rough-in drawing
for optimal power, water
and waste line locations.

5
CHILLER INSTALLATION

Section 4: Chiller Installation
6
1. Install the wall hanger onto the wall according to the rough-in drawing. See page 3.
The Wall hanger is shipped fastened to the back of the chiller unit.
2. Once the chiller unit is hung on the wall, Install a p-trap in the waste line and a shut off
valve in water supply line.
Refer to rough in drawing
for install locations and
dimensions
Install wall hanger bracket
with three chosen anchors
(not provided)
3. An in-line strainer is furnished in “Water Supply” tube. Connect “Water Supply” tube to
shut-off valve. NOTE: This connection should not be a solder joint or flare connection to
allow access to the strainer for service. Using one of the 1-3/4” diameter knockouts for a
waste line is not recommended because of a potential conflict with ADAtoe space
clearance requirements. Check your local building code inspector for approval.
4. Rotate fan blade by hand to see that it is free of obstructions.
5. Leave the front panel off for the Bottle Filler installation.
P-Trap

7
BOTTLE FILLER INSTALLATION

Section 4: Installation
8
1. The PGN8EBF comes partially assembled for shipping. Remove the kit from the
packaging and separate it into the assemblies and components shown below.
Tool Needed: T15 Torx bit
Drip Tray
Assembly
Filter
Support
Frame
Top
Cabinet
Assembly

Section 4: Installation
9
2. Place the bottle filler frame against the wall and set it onto the top flange of the chiller
frame.
Align the side edges of the bottle filler
and cooler frames to center the frame.
3. Affix the frame to the wall with at least 4 anchors into any appropriate anchor points
through the staggered slotted holes. Be careful to ensure the frame stays centered
on the cooler frame.
Choose a minimum of 4
anchors appropriate for the
surface the unit is being
mounted to. Anchors are
not provided.

Section 4: Installation
10
4. With 4x T15 Torx screws, assemble the drip tray assembly to the center bracket and
wall frame.
5. Attach the filter support bracket with 2x T15 Torx screws to the frame and drip tray
support bracket. This bracket helps to prevent the filter cartridge from falling into the
cooler unit below during installation or replacement.
Put IN FRONT OF
center bracket

Section 4: Installation
11
6. Attach one of the drain elbows to the drip tray stem. Insert the drainpipe provided into
the elbow and then attach another elbow onto the pipe. Use the remaining drainpipe
and connect the drip tray drainage system to the installed P-trap.
NOTE: Drainpipes will need to be positioned and cut to length as needed.
Drain Elbows
Drainpipes
P Trap
7. Assemble PGN8EBF wrapper to the installed frame. Rest the alcove on the drip tray
and ensure the wrapper walls rest OUTSIDE of the frame and side brackets.
NOTE: The drip tray will hold the weight of the wrapper but it is recommended to
keep a hold on the unit during installation for safety.
T15 Screws 4x

Section 4: Installation
12
8. If the outer edge of the drip tray is not properly aligned, loosen the screws mounting the
filter support and drip tray bracket to the frame and push forward or back as needed.
Then retighten the screws.
Slotted
Holes

Section 4: Installation
13
¼” Water Line With
Insulation Tubing
(Provided)
Solenoid Valve
Route the insulated cold water-out line up into the bottle filler cabinet and connect it to
the solenoid valve located in the alcove.
FOR UNFILTERED MODEL ONLY.
9.

Section 4: Installation
14
FOR FILTERED MODEL ONLY.
Connect the preassembled water source line to the shutoff valve. Note that there is an
in-line strainer inside the copper tubing of the water source line. IMPORTANT: It is
required to keep in-line strainer in system for unit to function properly; removing
strainer can cause damage to solenoid valve and/or cartridge system (if
applicable). DO NOT turn the water on. Next, connect the filter water-out line which is
connected to the cold tank inlet, to the filter outlet fitting.
Cold Tank
Inlet
Water
Source Line
Filter Inlet Filter Outlet
Filter Water-Out
Line
9.
Water
Source

Section 4: Installation
15
FOR FILTERED MODEL ONLY.
After the frame has been installed (not shown), insert the insulated water line from the
cold tank into the solenoid located at the top of the alcove assembly.
9.
Cooling Tank
Water Outlet
Cooling Tank Water
Outlet Line From
Fountain
Solenoid Valve
Inlet

Section 4: Installation
16
10.Connect the IEC connector to the power brick located behind the alcove of the bottle
filler. It is recommended to route the power cord from side opposite of the condenser
fan to ensure it does not become an obstruction.
Power Brick
IEC Connector
10.Turn on water source and check for leaks.
11. Ensure nothing is obstructing the fan blade. Plug the power cord back into the wall
outlet and then test to ensure the bottle filler is functioning properly.
FOR UNFILTERED MODEL ONLY.

Section 4: Installation
17
10.Install the provided filter cartridge by inserting the cartridge into the filter head and then
rotating 90 degrees until secured.
11. To flush the filter, ensure that the condenser fan is free from obstructions and plug in
the unit, then turn on the water source. Check for leaks.
FOR FILTERED MODEL ONLY.
Install
Cartridge into
Filter Head
Activate Bottle
Filler and Flush
into Container.
Dispense water into a container until the water becomes clear.

Section 4: Installation
18
12.Once the unit has been verified to be functioning properly, install the front cover panel by
inserting the top flanch up between the wrapper and center bracket, then tipping the
panel back to the fountain. Secure it with the 2x #8 hex or 2x T15 screws at the base of
the unit.
1
2
INSTALLATION COMPLETE.

19
Section 5: Set-Up Guide For OASIS® Hands-Free Bottle Filler
Electronics
•Units - Gallons
•Unfiltered unit
•Flow Meter = Rate Selected
•Filter Capacity = 4750 gallons [18000 liters] for a VersaFilter III
•
•Pushbutton
•Factory default program settings are:
•Bottle Count = 0.5L (1 Bottle)
•Flow Rate = 1.2 GPM
•20 second maximum dispense time
•To change the program settings, follow these steps:
•For each model top cap will need to be set aside until programming is complete. Remove top cap by unscrewing
two (2) T15 torx screws if needed. Remove wire tie bundling pushbutton inside bottle filler and feed it through hole in
cooler top. You can then adjust program using pushbutton through access panel of cooler.
•

Item
QTY
P/N
Description
19
1
042374
-001
Grille, Drip Tray
20
3
026675
-003
Screw, Flat HD Tapping
21
1
041207
-001-SP
Power Cord Assembly
22
1
038036
-003
Power Supply, 100
-240VAC/12VDC
23
1
042369
-001
Spout, ARF
24
1
041239
-002
Panel, ONN Top
25
1
038030
-002
Solenoid Valve 12VDC
26
1
038032
-001
Flow Nozzle Assembly
27
1
038029
-001
Adapter, Flow Nozzle Spout
28
1
029962
-103
FTG, PP Reducing Elbow
29
1
017681
-003-SP
Insulation, Sponge Tube 9"
30
1
030152
-102-SP
Tube, PE Cut Length WHI 10"
31
1
038037
-001
Lens, IR Bottle Filler
32
1
042065
-001
PCB, IR Sensor
33
1
042067
-001
Button Assy
–EBF
34
1
042066
-001
Ribbon Cable
–EBF
35
1
042068
-001
Assy, LED
–EBF
36
1
042064
-002
PCB, Main
- ARF
Item
QTY
P/N
Description
1
1
041245
-004
Frame
2
1
041250
-001
Panel, Front
3
1
041241
-001
Panel, Filter
4
1
041238
-006
Wrapper
5
2
A020967
1
-1/2" Elbow, W/ Nuts, 1-1/4"
6
4
039043
-001
Washer, Slip 1
-1/2" to 1-1/4"
7
1
036010
-002
Waste Tube 6.13"
8
1
036010
-013
Waste Tube 16.63"
9
1
041243
-002
Bracket, Center
10
1
18541
Clamp, Strain Relief
11
1
026642
-003
Screw, Hex HD Tapping #8 x 3/8"
12
1
026670
-001
Screw, Hex HD Machine #8 x 3/8"
13
24
031875
-003
Screw, Truss HD Tapping Torx #8
14
2
041242
-002
Bracket, Side
15
1
042370
-001
Cover, Front
- ARF
16
1
041246
-002
Bracket, Filter Support
17
1
041244
-004
Bracket, ONN DT ARF
18
1
412372
Drip Tray,
SurfM - ARF
20
Section 6: Bottle Filler Parts Breakdown
For PGN8FEBF Only (Filtered Model)
37
2
029994
-103
FTG, PP Elbow Plug
-In WHT
38
1
041146
-001
Head Assy, Manifold w/Elbow Ftg.
39
1
030152
-046-SP
Tube, PE 38" Long
40
1
030152
-046-Sp
Tube, PE 38" Long
41
1
041145
-001
Filter Cartridge, Versafilter III
42
1
041410
-004
Filter Bracket Frame Assembly