OBLICA | ELEMENTS INSTALLATION AND USER MANUAL
3.3 Storage of Inflammable Materials (e.g. firewood) in attached Elements
The following prerequisites must be fulfilled if you want to store highly flammable materials such as firewood
which are sufficiently ventilated to the front/to the side:
Elements above the firing chamber may only be used for storage stones. The storage of objects and in
particular of flammable materials is not possible.
For more detailed information please refer to the general assembly and operation instructions.
1.
The element is located below or
below/laterally from the firing
chamber. Here, no significant
heat transmission takes place.
It is also possible to close this
element by means of a flap.
2.
The element is mounted laterally at the
firing chamber and is equipped with a
special radiation protection insert against
heat transmission. If further extension
elements with smoke discharge tubes
are provided above this element (for the
storage of fuel), these must be equipped
additionally with a radiation protection
plate on the ground.
3.
The storage of flammable
materials above extension
elements where smoke
discharge tubes are fed
through is not possible.
3. INSTALLATION (CONTINUED)
Important installation instructions
_Installation:
It is imperative that the chimney stove be installed in strict conformity with any prevailing national and European standards as well as
any applicable local regulations. Please contact your local chimney sweep prior to installing your chimney stove.
_This skantherm fireplace model is suitable for integration into an alcove/cladding provided the safety distances indicated are observed.
_Installation of chimney stove:
Make sure that the floor‘s carrying capacity is sufficiently high. In case of inadequate carrying capacity, suitable adjusting measures
(e.g. plate for load distribution) are to be taken.
_Cleaning:
Make sure to clean your chimney stove at regular intervals. This also applies to emptying the ash box and cleaning the shaking grate.
Also make sure to clean the connection pieces and flues at least once a year and to apply a heat resistant copper paste on all moving
parts such as hinges at least once a year, too. Use a damp cloth and clear water to clean window glasses. Contact your local chimney
sweeper for professional cleaning of your chimney at regular intervals.
_Ventilation of room and chimney stove:
Please ensure sufficient ventilation of the room. Never close air supply openings or convection shafts of the stove.
_The fire chamber door of a stove operating independently of ambient air always has to be kept closed as otherwise, the
operation independent of ambient air cannot be guaranteed!
_Combustion air: In order to ensure a proper operation, sufficient air flow for the combustion has to be guaranteed. This
chimney stove is constructed to operate independently of ambient air and can either be connected directly outwards with a
combustion air conduit (type: FC41x) or to the air channel of an air exhaust chimney– LAS- (type: FC51x). The pressure loss
of the combustion air conduit may not be higher than 3 Pa. When using a flexible aluminium tube, please ensure that the pipe
is protected against mechanical damages. The combustion air should be lockable outwards with an air damper and the position
of the air damper should be visible in the installation room. Combustion air conduit as well as the connection piece need to be
airtight.
_The fireplace is not allowed for waste incineration!
_Note concerning the STORAGE OF INFLAMMABLE MATERIALS (e.g. firewood) in attached ELEMENTS:
The following prerequisites must be fulfilled if you want to store highly flammable materials such as firewood which are sufficiently
ventilated to the front/to the side:
_Elements above the firing chamber may only be used for storage stones.
The storage of objects and in particular of flammable materials is not possible.
For more detailed information please refer to the general assembly and operation instructions.
1.
The element is located below or below/
laterally from the firing chamber. Here,
no significant heat transmission takes
place. It is also possible to close this
element by means of a flap.
2.
The element is mounted laterally at the
firing chamber and is equipped with a spe-
cial radiation protection insert against heat
transmission. If further extension elements
with smoke discharge tubes are provided
above this element (for the storage of fuel),
these must be equipped additionally with a
radiation protection plate on the ground.
3.
The storage of flammable materials
above extension elements where
smoke discharge tubes are fed
through is not possible.
Necessary radiation
protection plate
Necessary radiation
protection insert
Important installation instructions
_Installation:
It is imperative that the chimney stove be installed in strict conformity with any prevailing national and European standards as well as
any applicable local regulations. Please contact your local chimney sweep prior to installing your chimney stove.
_This skantherm fireplace model is suitable for integration into an alcove/cladding provided the safety distances indicated are observed.
_Installation of chimney stove:
Make sure that the floor‘s carrying capacity is sufficiently high. In case of inadequate carrying capacity, suitable adjusting measures
(e.g. plate for load distribution) are to be taken.
_Cleaning:
Make sure to clean your chimney stove at regular intervals. This also applies to emptying the ash box and cleaning the shaking grate.
Also make sure to clean the connection pieces and flues at least once a year and to apply a heat resistant copper paste on all moving
parts such as hinges at least once a year, too. Use a damp cloth and clear water to clean window glasses. Contact your local chimney
sweeper for professional cleaning of your chimney at regular intervals.
_Ventilation of room and chimney stove:
Please ensure sufficient ventilation of the room. Never close air supply openings or convection shafts of the stove.
_The fire chamber door of a stove operating independently of ambient air always has to be kept closed as otherwise, the
operation independent of ambient air cannot be guaranteed!
_Combustion air: In order to ensure a proper operation, sufficient air flow for the combustion has to be guaranteed. This
chimney stove is constructed to operate independently of ambient air and can either be connected directly outwards with a
combustion air conduit (type: FC41x) or to the air channel of an air exhaust chimney– LAS- (type: FC51x). The pressure loss
of the combustion air conduit may not be higher than 3 Pa. When using a flexible aluminium tube, please ensure that the pipe
is protected against mechanical damages. The combustion air should be lockable outwards with an air damper and the position
of the air damper should be visible in the installation room. Combustion air conduit as well as the connection piece need to be
airtight.
_The fireplace is not allowed for waste incineration!
_Note concerning the STORAGE OF INFLAMMABLE MATERIALS (e.g. firewood) in attached ELEMENTS:
The following prerequisites must be fulfilled if you want to store highly flammable materials such as firewood which are sufficiently
ventilated to the front/to the side:
_Elements above the firing chamber may only be used for storage stones.
The storage of objects and in particular of flammable materials is not possible.
For more detailed information please refer to the general assembly and operation instructions.
1.
The element is located below or below/
laterally from the firing chamber. Here,
no significant heat transmission takes
place. It is also possible to close this
element by means of a flap.
2.
The element is mounted laterally at the
firing chamber and is equipped with a spe-
cial radiation protection insert against heat
transmission. If further extension elements
with smoke discharge tubes are provided
above this element (for the storage of fuel),
these must be equipped additionally with a
radiation protection plate on the ground.
3.
The storage of flammable materials
above extension elements where
smoke discharge tubes are fed
through is not possible.
Necessary radiation
protection plate
Necessary radiation
protection insert
Important installation instructions
_Installation:
It is imperative that the chimney stove be installed in strict conformity with any prevailing national and European standards as well as
any applicable local regulations. Please contact your local chimney sweep prior to installing your chimney stove.
_This skantherm fireplace model is suitable for integration into an alcove/cladding provided the safety distances indicated are observed.
_Installation of chimney stove:
Make sure that the floor‘s carrying capacity is sufficiently high. In case of inadequate carrying capacity, suitable adjusting measures
(e.g. plate for load distribution) are to be taken.
_Cleaning:
Make sure to clean your chimney stove at regular intervals. This also applies to emptying the ash box and cleaning the shaking grate.
Also make sure to clean the connection pieces and flues at least once a year and to apply a heat resistant copper paste on all moving
parts such as hinges at least once a year, too. Use a damp cloth and clear water to clean window glasses. Contact your local chimney
sweeper for professional cleaning of your chimney at regular intervals.
_Ventilation of room and chimney stove:
Please ensure sufficient ventilation of the room. Never close air supply openings or convection shafts of the stove.
_The fire chamber door of a stove operating independently of ambient air always has to be kept closed as otherwise, the
operation independent of ambient air cannot be guaranteed!
_Combustion air: In order to ensure a proper operation, sufficient air flow for the combustion has to be guaranteed. This
chimney stove is constructed to operate independently of ambient air and can either be connected directly outwards with a
combustion air conduit (type: FC41x) or to the air channel of an air exhaust chimney– LAS- (type: FC51x). The pressure loss
of the combustion air conduit may not be higher than 3 Pa. When using a flexible aluminium tube, please ensure that the pipe
is protected against mechanical damages. The combustion air should be lockable outwards with an air damper and the position
of the air damper should be visible in the installation room. Combustion air conduit as well as the connection piece need to be
airtight.
_The fireplace is not allowed for waste incineration!
_Note concerning the STORAGE OF INFLAMMABLE MATERIALS (e.g. firewood) in attached ELEMENTS:
The following prerequisites must be fulfilled if you want to store highly flammable materials such as firewood which are sufficiently
ventilated to the front/to the side:
_Elements above the firing chamber may only be used for storage stones.
The storage of objects and in particular of flammable materials is not possible.
For more detailed information please refer to the general assembly and operation instructions.
1.
The element is located below or below/
laterally from the firing chamber. Here,
no significant heat transmission takes
place. It is also possible to close this
element by means of a flap.
2.
The element is mounted laterally at the
firing chamber and is equipped with a spe-
cial radiation protection insert against heat
transmission. If further extension elements
with smoke discharge tubes are provided
above this element (for the storage of fuel),
these must be equipped additionally with a
radiation protection plate on the ground.
3.
The storage of flammable materials
above extension elements where
smoke discharge tubes are fed
through is not possible.
Necessary radiation
protection plate
Necessary radiation
protection insert
