Oblica STUV 16 User manual

1. TECHNICAL DATA 2
2. PRE-INSTALLATION 3
3. INSTALLATION 5
4. OPERATION 9
5. TESTING 10
Keep for future use
STUV 16:
MODEL SPECIFICATIONS
^

PAGE 2
OBLICA | STUV 16 INSTALLATION AND USER MANUAL
^
1. TECHNICAL DATA
DETERMINED UNDER TEST CONDITIONS:
Nominal thermal output 7kW
Efficiency (Australian Test) 60%
Emissions (Australian Test) 0.7 g/Kg
6/8” Flue
780
625400
WOOD
STORE
WEIGHT AND DIMENSIONS:
Dimensions Firebox W780 x H625 x D456mm
Firebox weight 121Kg
Flue kit Standard 6”/8”/10”

PAGE 3
OBLICA | STUV 16 INSTALLATION AND USER MANUAL
^
2. PRE-INSTALLATION
Congratulations on your purchase of the STUV 16. This appliance should be installed and checked by a qualified
professional. Ensure you have read the operation guidelines thoroughly prior to first use. For any questions or concerns
please contact Oblica on 03 9416 0400.
The installation process is outlined below:
– Determine position of firebox and flue carefully observing the clearances described within this section
– Install the external flue
– Install the internal flue and engage the firebox
– Ensure the floor has adequate protection
CAUTION:
Using components or parts other than those provided by the manufacturer or modifying the specification of components
may result in inferior or unsafe operation. If such action is necessary, consult the manufacturer in the first instance.
WARNING:
• The appliance and flue-system must be installed in accordance with AS/NZS 2918 and the
relevant building code or codes.
• Any modification of the appliance that has not been approved in writing by the testing authority
will be in breach of the approval granted for compliance with AS/NZS 4013.
• Once the flue has been installed and approved by a professional installer, the flue must not be
modified in any way.
^

PAGE 4
OBLICA | STUV 16 INSTALLATION AND USER MANUAL
^
MINIMUM CLEARANCE – INTERNAL
2.1 Clearance from non-combustible surfaces
(eg masonry)
100mm minimum clearance is required from fully
non-combustible surfaces.
100
100
250mm
Non Combustible
Non Combustible
Glass (frameless or aluminium frame)
Glass (frameless or aluminium frame)
250mm
250mm
Combustible
Combustible
Combustible
Combustible
600mm
100
100
2.2 Clearance from glass
250mm minimum clearance is required from normal
non-combustible glass.
2.3 Clearance from combustible surfaces
(eg timber joist & concrete)
Clearances may be reduced with the application of
heat shielding to walls in accordance to the
Australian Building Code.
For information on heat shielding please contact our
office on 03 9416 0400 or email [email protected].
IMPORTANT:
Frames must also be considered. Timber window
frames must be treated as combustible surfaces
(see 2.3). Aluminium frames can be treated as
non-combustible surfaces (see 2.2).
2. PRE-INSTALLATION (CONTINUED)
100
100
250mm
Non Combustible
Non Combustible
Glass (frameless or aluminium frame)
Glass (frameless or aluminium frame)
250mm
250mm
Combustible
Combustible
Combustible
Combustible
600mm
100
100
100
100
250mm
Non Combustible
Non Combustible
Glass (frameless or aluminium frame)
Glass (frameless or aluminium frame)
250mm
250mm
Combustible
Combustible
Combustible
Combustible
600mm
100
100
100
100
250mm
Non Combustible
Non Combustible
Glass (frameless or aluminium frame)
Glass (frameless or aluminium frame)
250mm
250mm
Combustible
Combustible
Combustible
Combustible
600mm
100
100
Configuration 1 – Parallel installation
Configuration 2 – Corner installation

PAGE 5
OBLICA | STUV 16 INSTALLATION AND USER MANUAL
^
Cowl (Chinaman Hat)
8” Outer Case
10” Outer Case
8” Outer Case
10” Outer Case
6” Active Flue
6/8/10” Flue
CEILING RING
RUBBER
DEKTITE FLASHING
3. INSTALLATION
3.1 Installing flue kit
Ensure flue is installed as per Australian
standards (see the following diagrams below).
NOTE:
The active flue must go
inside the fireplace spigot.

PAGE 6
OBLICA | STUV 16 INSTALLATION AND USER MANUAL
^
3. INSTALLATION (CONTINUED)
The top of the flue must be 400mm higher than the highest point of the roof. Alternatively, there must be a
minimum distance of 3 meters from any higher section of roof.
> 40 cm
–> 40 cm
–> 40 cm
–
> 3 m
–
> 900 cm
–
> 3 m
–
> 900 cm
–
> 900 cm
–
> 40 cm
–> 40 cm
–> 40 cm
–
> 3 m
–
> 900 cm
–
> 3 m
–
> 900 cm
–
> 900 cm
–
The top of the flue must be 900mm above the roofline. Alternatively, there must be a minimum distance of
3 meters from any higher section of roof.
PITCHED ROOF INSTALLATION
FLAT ROOF INSTALLATION (LESS THAN 5˚ PITCH)

PAGE 7
OBLICA | STUV 16 INSTALLATION AND USER MANUAL
^
3.2 Protecting the floor
• If installed directly on combustible material, the floor protector must be made of a minimum 12mm thick cement
sheet. Non-combustible finishes can be applied to the floor protector (tiles, steel sheet, light concrete, etc).
• If the combustible floor is installed on concrete, you can replace the combustible material with non-
combustible material laid directly onto the concrete.
• If the appliance is installed less than 400mm above the floor protector then the floor must be made of
non-combustable material.
Joist
Insulative board (12mm)
+ non combustible finish
Concrete
Combustible
floor
(eg. timber)
Joist
500mm
400mm
167.5 167.5
955mm
1060mm
Combustible floor
(eg: Timber)
Floor protector
Insulative board (12mm)
+ non combustible finish
Combustible
floor
(eg. timber)
400mm
Insulative board (12mm)
+ non combustible finish
Combustible
floor
(eg. timber)
400mm
FLOOR PROTECTOR LAID ON TIMBER FLOOR
3. INSTALLATION (CONTINUED)
Joist
Insulative board (12mm)
+ non combustible finish
Concrete
Combustible
floor
(eg. timber)
Joist
500mm
400mm
167.5 167.5
955mm
1060mm
Combustible floor
(eg: Timber)
Floor protector
Insulative board (12mm)
+ non combustible finish
Combustible
floor
(eg. timber)
400mm
Insulative board (12mm)
+ non combustible finish
Combustible
floor
(eg. timber)
400mm
FLOOR PROTECTOR LAID ON JOIST

PAGE 8
OBLICA | STUV 16 INSTALLATION AND USER MANUAL
^
Joist
Insulative board (12mm)
+ non combustible finish
Concrete
Combustible
floor
(eg. timber)
Joist
500mm
400mm
167.5 167.5
955mm
1060mm
Combustible floor
(eg: Timber)
Floor protector
Insulative board (12mm)
+ non combustible finish
Combustible
floor
(eg. timber)
400mm
Insulative board (12mm)
+ non combustible finish
Combustible
floor
(eg. timber)
400mm
Joist
Insulative board (12mm)
+ non combustible finish
Concrete
Combustible
floor
(eg. timber)
Joist
500mm
400mm
167.5 167.5
955mm
1060mm
Combustible floor
(eg: Timber)
Floor protector
Insulative board (12mm)
+ non combustible finish
Combustible
floor
(eg. timber)
400mm
Insulative board (12mm)
+ non combustible finish
Combustible
floor
(eg. timber)
400mm
FLOOR PROTECTOR LAID ON CONCRETE
3. INSTALLATION (CONTINUED)
TOP VIEW

PAGE 9
OBLICA | STUV 16 INSTALLATION AND USER MANUAL
^
4. OPERATION
4.1 What you should burn
• Untreated, air dried hardwood
• Split logs with a humidity content of less than 20%
4.2 Do not burn
• Trash
• Painted plastic
• Coated or preservative treated wood
• Waste or black coal
• Inflammable liquids
• Fire gels
• Moist wood with a residual humidity content of more than 20% (this may cause soothing of the chimney).
WARNING:
• Do not use flammable liquids or aerosols to start or rekindle the fire.
• Do not use flammable liquids or aerosols in the vicinity of the fireplace when operating.
• Do not store fuel within prescribed installation clearance distances.
• The use of some types of preservative-treated woods as a fuel can be hazardous.
IMPORTANT:
• Misuse may lead to unhealthy and environmentally harmful emissions and will void any warranty or guarantee.
• The maximum load capacity for the STUV 16 is 6kg of wood.
• Burning only seasoned hardwood helps to protect the environment and lower emissions.
For details of a wood supplier in your area please call our office on 03 9416 0400 or email [email protected].
^

PAGE 10
OBLICA | STUV 16 INSTALLATION AND USER MANUAL
^
5. TESTING
TEST REPORT NO ASFT19084 24/10/2019
TESTING LABORATORY: Australian Solid Fuel Testing
MANUFACTURER: Stuv
MODEL: STUV 16
WORK REQUESTED: Assessment of appliance to AS/NZS 4012:2014
for determination of Power Output and Efficiency
and AS/NZS 4013:2014 for Flue Gas Emission
using hardwood fuel.
ISSUE DATE: 24/10/2019
INVESTIGATING OFFICER: Steve Marland
RESULTS: The appliance particulate emission factor established
in testing is 0.7g/kg of dry wood*, within the maximum
specification of 2.5g/kg of dry wood and an efficiency of 60%.
CONCLUSION: This appliance does comply with the requirements
of AS/NZS 4012:4013 (2014) for the configuration tested.
*and a 60% efficiency
^
^