Odorox Decon User manual

Decon Scrubber
Owner’s Manual
Serial # ____________________
REV0001111209
TM

TABLE OF CONTENTS
Warning 1
Operating the Decon Scrubber 2
System Placement 4
Caring for your Decon Scrubber 5
Cleaning Instructions 6
Optic Replacement Instructions 7
Filter Replacement Instructions 10
Specication and Warranty 13

ENGLISH
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety
precautions should always be followed to reduce
the risk of re, electric shock, and injury to
persons, including the following:
• Read all instructions before using this Hydroxyl
Generator.
• To avoid re or shock hazard, plug the equipment
directly into a 120V AC electrical outlet.
• If the generator is covered by a bag when
shipped: Remove plastic bag before use.
• Keep the cord out of heavy trafc areas. To avoid
re hazard, NEVER put the cord under rugs, near
heat registers, radiators, stoves, or heaters.
• To protect against electrical hazards, DO NOT
immerse in water or other liquids. Do not use near
water.
• Close supervision is necessary when any
generator is used by or near children, or disabled
persons.
• WARNING! Always unplug the generator before
moving it, cleaning, or whenever the generator is
not in use. Be sure to pull by the plug and not
the cord.
• NEVER drop or insert any object into any
openings.
• DO NOT use an extension cord. Doing so can
create potential safety hazards.
• DO NOT operate any generator with a damaged
cord or plug, if motor fan fails to rotate, after the
generator malfunctions, or if it has been dropped
or damaged in any manner. Return generator
to manufacturer or authorized repair facility for
examination, electrical or mechanical adjustment,
or repair.
• Use generator only for intended use as described
in this manual. Any other use not recommended by
the manufacturer may cause re, electric shock,
or injury to persons. The use of attachments not
recommended may cause hazards.
• DO NOT use outdoors.
• NEVER block the air openings, grills/outlets or
place on a soft surface such as a bed or sofa, as
this could cause the unit to tip over, blocking the
Air Intake Opening/Grill.
• Keep unit away from heated surfaces and open
ames.
• CAUTION: For General Ventilating Use Only.
Do Not Use to Exhaust Hazardous or Explosive
Materials and Vapors.
• DO NOT attempt to repair or adjust any electrical
or mechanical functions on this unit. Doing so will
void your warranty. The inside of the unit contains
no user serviceable parts. All servicing should be
performed by qualied personnel only.
• WARNING! To reduce the risk of re or electric
shock, DO NOT use this generator with any solid-
state speed control device.
• DO NOT place anything on top of generator.
• DO NOT plug the cord in with wet hands: electric
shock could result.
• NEVER use detergents, gasoline, glass cleaner,
furniture polish, paint thinner or other household
solvents to clean any part of the generator.
• To avoid a shock, plug the unit’s three-prong
plug into a grounded outlet.
• DO NOT under any circumstances cut or remove
the third (Ground) prong from power cord. For
personal safety, this generator must be properly
grounded.
WARNING!
IMPORTANT SAFETY INFORMATION. READ ALL
INSTRUCTIONS BEFORE USING.
Use this Hydroxyl Generator only for its intended
purpose as described in this Owner’s Manual.
1

The Control Panel
1) Main Power Switch – Turns power on to the Decon Scrubber. This switch must be in the “ON”
position before trying to control the “FAN SPEED” or “PROCESSOR” switches.
2) Fan Speed Switch – Controls the speed of the fan and airow through the system.
3) Processor Switch – OFF/LOW/HIGH. This switch controls the number of hydroxyl generating
optics in operation.
4) Hour Meter – Quartz non-reversible indicator of accumulated hours of use.
5) Minihelic Gauge – Gauge which senses the static pressure through the 4 inch lter. Used to indi-
cate when it is time to replace the 4 inch lter.
6) Processor Indicator (Green) – Indicates that the hydroxyl generating optics are on.
7) 15 Amp Breaker – AC power circuit protection for the Decon Scrubber.
8) 2 Amp Breaker – AC power circuit protection for the optic circuit.
ENGLISH OPERATING THE DECON SCRUBBER
2

ENGLISH
OPERATING THE DECON SCRUBBER
3
POWER ON
The main power for the scrubber can be switched on by turning the MAIN POWER switch to the ON
position.
POWER OFF
The main power for the scrubber can be switched off by turning the MAIN POWER switch to the OFF
position.
FAN SPEED
The Decon Scrubber is equipped with an air mover fan, which runs between 750 and 1500 cubic feet
per minute.
In order for the fan to turn on, the MAIN POWER switch must be in the ON position. Once the MAIN
POWER switch is on, the fan speed can be controlled by rotating the FAN SPEED knob clockwise to
increase the speed, or counter clockwise to decrease the speed.
PROCESSOR SWITCH
The Decon Scrubber is equipped with three hydroxyl generating optics. In order for these optics to
turn on, the MAIN POWER switch must rst be turned on.
With the PROCESSOR switch in the OFF position, all optics are off.
With the PROCESSOR switch in the LOW position, two optics are on. The green PROCESSOR
indicator will turn on in this position.
With the PROCESSOR switch in the HIGH position, all three optics are on. The green PROCESSOR
indicator will turn on in this position.

The manner in which you position the Decon Scrubber can have a big impact on
its efciency. You may have to experiment a little to nd the best position for the
system. You should position the system as per (Figure 1) for efcient decontami-
nation.
If you are using two or more systems, place them so they blow into the contami-
nated area to create a vortex. For example, if you are using two systems, place
one on each side of the affected area (Figure 2).
ENGLISH SYSTEM PLACEMENT
4
Figure 2
Figure 1

Warning: DISCONNECT the unit from an electrical power source before
performing any maintenance or cleaning on the unit.
SYSTEM CASE CLEANING
Exterior
The exterior of the machine can be cleaned with mild dishwashing detergent and a clean cloth, and
then rinsed with clean water. DO NOT use any all-purpose cleaners with harsh detergents or abra-
sives, as these may damage the decals and the exterior nish. Care should also be taken to avoid
spraying or otherwise directing detergent or water into or around electrical components.
Interior
The interior of the Decon Scrubber can be cleaned in the same manner as the exterior.
OPTIC CLEANING
Cleaning of the optics is recommended to maintain peak processing efciency. Fingerprints, smudg-
es, dirt, dust particles, etc. will interfere with the hydroxyl production and should be avoided.
Note: Remove the optics from the optic chamber prior to cleaning to avoid any damage to
the optics during the cleaning process (refer to the Optic Replacement Instructions for proper
removal).
To clean the optics, use a solution of 10% Isopropyl Alcohol (Isopropyl Alcohol strength of 70% or
90%) and 90% ltered/distilled water on a clean lint-free cloth and wipe gently. Do not use any type
of commercial glass cleaner. Using another lint-free cloth, gently wipe the optic until completely dry.
Allow the optic to dry completely (20 minutes) before operating the system.
ENGLISH
CARING FOR YOUR DECON SCRUBBER
5

ENGLISH CLEANING INSTRUCTIONS
6
Step 1 - Turn “Main Power” switch to the “OFF” position
Step 2 - Unplug power cord from 120 volt receptacle
* NOTE - Use caution to pull from the plug and not from the cord
Step 3 - Remove 4 inch and 2 inch lters (refer to lter replacement instructions)
* CAUTION - Use clean leather gloves and eye protection when handling the optics in this unit
Step 4 - Remove optics (refer to optic replacement instructions)
Step 5 - Remove top panel by removing Phillips screws and gently pulling off panel
Step 6 - Use compressed air to blow out all compartments
Step 7 - Using a cleaning solution of 10% Isopropyl Alcohol (Isopropyl Alcohol strength of 70% or
90%) and 90% ltered or distilled water in a spray bottle, wipe down all interior components (and
removed covers/panels) with clean lint-free towels
Step 8 - Clean optics with same solution and clean lint-free towels
* CAUTION - Optics are fragile. Take extreme care while holding and cleaning optics, as
breakage or broken wires may occur.
Step 9 - Install clean optics (refer to optic replacement instructions)
Step 10 - Install new lters (refer to lter replacement instructions)
Step 11 - Re-install top panel

Step 1 - Turn “Main Power” switch to the “OFF” position
Step 2 - Unplug power cord from 120 volt receptacle
* NOTE - Use caution to pull from the plug and not from the cord
Step 3 - Gently lay Decon Scrubber down on the front side (side opposite handle)
* NOTE - Ensure unit is set on a stable non-scratch surface
* CAUTION - Unit is heavy! Use proper lifting techniques and at least two people to avoid
injury
Step 4 - Remove Phillips (Star) screws on bottom panel
Step 5 - Remove bottom panel and set aside
* CAUTION - Use clean leather gloves and eye protection when handling the optics in this unit
ENGLISH
OPTIC REPLACEMENT INSTRUCTIONS
7

Step 6 - Disconnect optic to be replaced by holding the optic base with one hand, and the optic har-
ness connector with the other hand. Gently ‘wiggle’ connector while pulling from the optic base.
Step 7 - Gently pull optic from three optic supports
* Note - Do not put any pressure on the side of the optic without support
Step 8 - Gently install new optic by pressing into the three optic supports
* Note - Portion of optic containing the connector must be side pressed into the optic supports
ENGLISH OPTIC REPLACEMENT INSTRUCTIONS
8

ENGLISH
OPTIC REPLACEMENT INSTRUCTIONS
9
Step 9 - Re-connect optic connector
* Optic connector is keyed and will only connect in one direction. If unable to connect optic
base with optic connector, rotate connector 180º and try again.
Step 10 - Re-install bottom panel with Phillips (Star) screws previously removed

Main 4 Inch Filter
Step 1 - Turn “Main Power” switch to the “OFF” position
Step 2 - Unplug power cord from 120 volt receptacle
* NOTE - Use caution to pull from the plug and not from the cord
Step 3 - Remove the two top Phillips (Star) screws (or push and turn the phillips quarter turn fastener
counter clockwise) on the main lter door
Step 4 - Swing top of main lter door down
Step 5 - Remove 4 inch lter
Step 6 - Install new 4 inch lter
* NOTE - Ensure proper lter direction with reinforcing mesh on top
Step 7 - Close main lter door and reinstall the two Phillips (Star) screws previously removed (or push
and turn the phillips quarter turn fastener clockwise)
ENGLISH FILTER REPLACEMENT INSTRUCTIONS
10

2 Inch Pre-Filters
Step 1 - Turn “Main Power” switch to the “OFF” position
Step 2 - Unplug power cord from 120 volt receptacle
* NOTE - Use caution to pull from the plug and not from the cord
Step 3 - Remove the Phillips (Star) screw located at the top of the pre-lter door (or push and turn the
phillips (Star) quarter turn fastener counter clockwise)
Step 4 - Pull the top of the pre-lter door out and lift off
Step 5 - Remove 2 inch lter
Step 6 - Install new 2 inch lter
* NOTE - Ensure proper lter direction with reinforcing mesh facing the inside of the unit
Step 7 - Reinstall the pre-lter door by rst installing the tab portion of the door into the bottom of the
opening
ENGLISH
FILTER REPLACEMENT INSTRUCTIONS
11

Step 8 - Keep pressure on the bottom of the door while the top gets pushed in place
Step 9 - Reinstall Phillips (Star) screw previously removed (or push and turn the phillips (Star)
quarter turn fastener clockwise)
ENGLISH FILTER REPLACEMENT INSTRUCTIONS
12

ENGLISH
SPECIFICATIONS AND WARRANTY
13
SPECIFICATION
Dimensions: 28” x 25” x 44” (71.1cm x 63.5cm x 111.8cm)
Weight: 125 lbs (56.7kg)
Power Requirements: 120 Volt AC, 12 Amp
Starting: 2-Position Switch
Fan Control: Variable Speed Control 750 to 1500 cfm
Meter: 1/10 Quartz Hour Meter
WARRANTY
HGI Industries, Inc. warrants that this Decon Scrubber (excluding spare parts and consumables) shall
be free from defects in workmanship or materials for a period of one (1) year from the delivery thereof
to the customer.
CONTACT INFORMATION
For replacement parts, warranty service, or any questions regarding the operation and maintenance
of your Decon Scrubber, please contact your local authorized dealer.
Please visit www.odoroxair.com.

CONTACTING YOUR LOCAL DISTRIBUTOR
For replacement parts, warranty service, or any questions regarding
the operation and maintenance of your Odorox® product, please
contact your local Odorox® distributor.
Odorox® Hydroxyl Generators are proudly manufactured in the USA.
Copyright © 2011, HGI Industries Incorporated
Odorox and Boss XL3 are trademarks or registered trademarks of HGI Industries Incorporated, Boynton Beach, Florida USA.