Odys DPF-Shine User manual

ODYS DPF-Shine
1/8
EN
ODYS DPF-Shine
U
U
US
S
SE
E
ER
R
R
M
M
MA
A
AN
N
NU
U
UA
A
AL
L
L
CONGRATULATIONS on your purchase of our 7’’LCD Digital Photo Frame. Please read carefully and
follow all warnings and instructions in this User’s Manual and those marked on the product before first
use. Failing to follow these warnings could result in personal injury or damage to the Digital Photo Frame.
Also, remember to keep this User’s Manual in a convenient location for future reference.
Important: Save the original box and all packing material for future shipping needs.
IMPORTANT PRODUCT SAFETY INSTRUCTIONS
Proper Handling of the Digital Photo Frame
Always handle the Digital Photo Frame with care. Avoid touching the LCD screen as natural skin oils are
often difficult to remove.
Always position the Digital Photo Frame on a stable and level surface. Unstable surfaces can cause the
Digital Photo Frame to topple and fall, resulting in possible damage or injury.
Avoid exposing the Digital Photo Frame to direct sunlight or high temperatures, which can damage or
shorten its useful life. Do not place the unit near heat sources such as radiators, heat registers, or other
appliances that generate heat. Orient the Digital Photo Frame away from direct sunlight to reduce glare.
Avoid exposing the Digital Photo Frame to rain, water, moisture or high humidity. Do not place it in a
bathroom or kitchen near a sink or where it may come in contact with water.
Never place heavy or sharp objects on the LCD panel, frame, or power cord.
Overloading Outlets
Do not overload electrical power sources when using the Digital Picture Frame. Overloading wall outlets,
or extension cords can result in overheating, fire, or electric shock. Use only grounded or polarized
outlets.
Power Cord Protection
Minimize wear on the power supply cord. The power supply cord should be routed away from foot traffic
and contact with other objects. Do not route the power cord under rugs or carpeting. The cord should
never be severely bent, pinched, or twisted. Periodically inspect the power cord and each end of the cord
for wear or damage. Periodically inspect the power cord and each end of the cord for wear or damage.
Ventilation
Slots and openings on the Digital Photo Frame are provided for ventilation purposes. To ensure reliable
operation of the product and to protect it from overheating, these openings must not be blocked or
covered. Keep the Digital Photo Frame a minimum of four (4) inches away from any wall to assure
sufficient airflow and ventilation. Increased temperatures may cause fire or device failure.
To assure proper ventilation, do not block the openings by placing the Digital Photo Frame on a bed,
sofa, rug or other similar surface. Do not place it in a built-in installation, such as a bookcase or enclosed
rack, unless proper ventilation is provided.

ODYS DPF-Shine
EN
Other Notices and Precautions
Caution: Never remove the plastic casing. There are no user serviceable parts inside. The Digital Photo
Frame contains high voltage parts. You may be seriously injured if you touch them.
Do not attempt repairs yourself. The warranty does not cover repairs or attempted repairs by anyone not
authorized byAuthorize Dealer. Refer all servicing and repairs to qualified service personnel.
If the Frame begins to emit smoke, an abnormal noise, or a strange odor, immediately turn it off and
unplug the power cord. Contact the Authorize Dealer Service Center.
If the Digital Photo Frame will not be used for an extended period of time, unplug the power cord.
Cleaning the Digital Photo Frame
•MAKE SURE THE DIGITAL PHOTO FRAME IS TURNED OFF
•NEVER SPRAY OR POUR LIQUID DIRECTLY ONTO THE SCREEN OR PLASTIC CASING
To Clean the Screen:
1.Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2.If it still is not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner on a
clean, soft, lint-lint-free cloth to clean the screen.
To Clean the Plastic Casing:
1.Use a soft, dry cloth.
2.If it still is not clean, apply a small amount of non-ammonia, non-alcohol based, and mild
non-abrasive detergent on a clean, soft, lint-free cloth to clean the surface.
To Clean the Frame:
Use a soft, dry cloth.
Disclaimer
Your Authorize Dealer does not recommend the use of any ammonia or alcohol-based cleaners on
the LCD screen or plastic casing. Some chemical cleaners have been reported to damage the screen
and / or display case. Your Authorize Dealer will not be liable for damage resulting from the use of any
ammonia or alcohol-based cleaners.
Tips regarding environmental protection
At the end of its operating life, this product may not be disposed of by way of your normal household waste. Instead it must
be delivered to a collection point for recycling electrical and electronic equipment. The icon on the product, in the operating
instructions or on the packaging, indicates this.
The materials used in manufacturing this product are recyclable, depending on their identifying markings. By recycling this
equipment, by recycling its components, or through other procedures of re-using outdated equipment, you are making an
important contribution to protection our environment. Please ask you local municipal administration for the location of the
corresponding recycling point.
Battery Recycling
In order to ensure the environmently friendly disposal of batteries, please do NOT dispose of used batteries through
normal household waste. Please take the batteries to your local retail or community collection point for recycling.
The following may be an indication of a discharged battery: The device cannot be switched on. The device switches
off automatically and "Battery Empty" is shown in the display. The device and or battery do not function properly.

ODYS DPF-Shine
3/8
EN
TABLE OF CONTENT
Product Overview.....................................................3
Language Settings...................................................3
Package Content ......................................................3
Buttons & Ports........................................................3
Remote Control........................................................4
Mounting the Digital Photo Frame............................4
Install the bracket.................................................................................................................................... 4
Connect to a wall outlet via the DC adaptor ............................................................................................ 4
Inserting a memory card/USB flash disk.................................................................................................. 4
Turn on or off the screen .........................................5
View Photos .............................................................5
Calendar...................................................................6
System Settings .......................................................6
Firmware Upgrade....................................................7
Troubleshooting........................................................7
Technical Specifications............................................7
Warranty condition...................................................8
Product Overview
The 7" Digital Photo Frame enables you to view photos on a high-resolution LCD screen.
Simply insert a USB flash drive or SD memory card into the appropriate slot located on the
back of the frame and your pictures will be displayed instantly on the screen without need of
paying money for printing photos.
Language Settings
For easy operation of the device it is suggested to use the remote control included.
Remove the battery protection from the remote and insert a new battery.
Switch the device on, the device will start in the Main Menu.
2x Press the -key twice to enter and select the menu "Setting"
OK Confirm by pressing the "OK" Key.
3x Press the -key three times and select the menu "Language".
/Use the/keys to select the desired language.
ESC Exit the menu by pressing the ESC-Key. The settings will now be saved.
Package Content
Buttons & Ports
•7" Digital Picture Frame
•User manual
⑤
⑥
⑧
⑨
⑩
⑦
③
①
②④
③


②
•DCAdaptor
•Remote Control
LCD Display
Card Slot Cover – Open the cover from the OPEN slot to show the
memory card slot.
Bracket
Bracket Holder
– Turn on or turn off the screen
MENU – Confirm selection
ESC – Return
Left –Move the cursor left.
Right –Move the cursor right
Up – Move the cursor up
Down – Move the cursor down \ Open Thumbnail preview
USB port – Connect to a USB flash drive
DC IN port – Connect to the AC adaptor

ODYS DPF-Shine
EN
Remote Control
Mounting the Digital Photo Frame
Install the bracket
The included bracket is used to support the frame on any flat surface.
To install the bracket,
1) Screw off the nut from the back of the device.
2) Place the bracket onto the screw hole.
3) Return the screw to the hole and tighten it for securing the bracket.
Connect to a wall outlet via the DC adaptor
The digital photo frame is powered by 5V DC IN input. Connect the DC adaptor to the DC IN port on the back
and the electronic wall socket (see the following figure). The device should start immediately once powered.
Inserting a memory card/USB flash disk
The device provides a card slot to support memory card and a USB port for USB flash disk. Please follow these
steps to insert a memory card or USB flash disk:
(1) Find the card slot or USB port at the bottom of the machine.
(2) Insert a memory card into the slot with the face toward the back, or insert a USB flash disk into the USB port.
Open the card
slot cover
Key Function
Turn on or off the screen
SLIDE Change transition effect of slide show
MODE Set the aspect ratio as 4:3, 16:9 and Original
Move the cursor up / Set the brightness of the screen when
viewing photo
Move the cursor down / Open Thumbnail preview
Display the previous photo or move the cursor left
Display the next photo or move the cursor right
ENTER Confirm a selection / Display the tool bar when viewing photo
ESC Return
SETUP Enter system setting mode
TIME Display the calendar / Set the time interval between slides when
you are in slide show
ZOOM Zoom in or zoom out the photo
ROTATE Rotate right 90°
S
crew t
h
e nut to re
l
ease or
tighten the bracket

ODYS DPF-Shine
5/8
EN
•Don’t change the SD / MMC/MS card while Picture Frame is powered on!
If you want to change the card turn the power off at first.
•Please insert the card in a correct direction. Do not apply too strong a force when inserting
the card to prevent damaging the card or the component of digital photo frame. Please
check for a correct inserting direction if it can not be done.
•Don't insert or pull out the saving card while reading information.
Turn on or off the screen
When you do not want to view the photos momentarily, you can press the button to turn off the screen for
saving power. To turn on the screen, press the button again.
View Photos
Step 1: Connect the device to a wall outlet with the AC adaptor.
Step 2: The device should start immediately and display the main menu.
Photo – Display photos
Calendar – Display the calendar
Setting – System Setting
Step 3: Insert a USB flash disk into the USB port or a memory card into the
card slot.
Step 4: Press the (up) / (down) button to select “Photo” and then press
the “Mode” button to confirm. The slide show should start automatically.
Step 5: Press the “Mode” button to show the tool bar. Press the /button
to select a button from the tool bar and then press “Mode” button to confirm.
Previous/next
Select to display the previous photo.
Select to display the next photo.
Slide Show
Select /to start or stop slide show.
Rotate the picture
Select to rotate the picture clockwise by 90°.
Change the Aspect Ratio
Select to change the aspect ratio between 4:3, 16:9 and
Original.
Display photo information
To display information (photo name, format, size etc.) about the photo, select “ ”.
Please disconnect the device from the power source when not to be used for longer periods of
time. Doing so will save energy and extend the life of the device.
If you insert
b
oth, only pictures stored in the memory device that
you inserted firstly are displayed.
Zoom in/out
Select to zoom in or zoom out the picture to
0.5, 0.7, 1, 1.5 and 2X. When the photo is
enlarged, you can press the ,,and 
button to roam on the photo. Pressing the ESC
button will restore the picture to original size.

ODYS DPF-Shine
EN
Thumbnail View
Select to enter the thumbnail view mode.
Press ,,and to select a picture.
Press the “Mode” button to confirm your selection and enlarge the photo to full
screen.
Press the ESC button to return to the main menu.
Set brightness of the screen
When you are viewing a photo, you can press the or button to activate the
brightness setting.
Step 6: Press the ESC button to exit and return to the main menu.
Calendar
The Digital Photo Frame can be used as a tabletop calendar and an alarm clock.
Calendar View
To enter the calendar view mode, on the main menu, select the “Calendar” from the main menu, and then press the
“Mode” button to confirm. The calendar and the time should display. At the same time, all photos are displayed in
slide show at the left top corner.
Press the and button to change the year.
Press the and button to change the month.
Press the ESC button to exit and return to the main menu.
Clock View
When you are viewing the calendar, you can press the Mode button to display
the time as a clock.
Press the ESC button to exit from the clock.
Set the Alarm
To enable the alarm,
(1)On the main menu, press the “Setting” button to enter the system setting
mode.
(2)Press and button to select “Alarm”.
(3)Press the and button to select the hour, minute and day setting.
(4)Press the/button to decrease or increase the level of hour, minute and day.
Alarm day options:
None – Disable the alarm.
Everyday – Alarm rings everyday.
Once – Alarm rings once.
System Settings
On the main menu, select “Setting” and then press the “M” button to enter the
system setting mode.
Please note: To insure proper display, the date and time must be set in the system settings.
Slide Show
Current Time
Alarm Time
Alarm Day

ODYS DPF-Shine
7/8
EN
Press the and button to select a setting item.
Press the /button to change the option for the selected setting.
Press the ESC button to confirm setting and exit.
Transition Effect – Set transition effect of the slide show
Slideshow Interval – Set time interval between slides.
Startup Mode – Set the first mode that you see when the device starts up.
Language – Set the language of the on-screen texts
Alarm – Set the alarm time
Clock – Set the time
Date – Set the date
Update – Update the software
Reset – Restore the system settings to default
About – Display the software version information
Firmware Upgrade
To get the latest version of software,
(1) Obtain the upgrading file.
(2) Copy the upgrading file to the root of a memory device.
(3) Insert the memory device into the photo frame.
(4) Enter the system setting mode, press the button to select “Update” and then press the “Mode” button
to continue.
(5) Press /to select “Yes” and then press the Mode button to confirm.
(6) Wait for the upgrading to complete and do not interrupt the progress.
(7) The device restarts when the upgrading is finished.
Troubleshooting
The digital picture frame cannot be powered
on. · Make sure that the AC adapter is connected securely to the frame and the
power source.
Remote control does not work · Ensure that a working battery is inserted
The images can not be displayed. · Make sure the image file is in a supported
formats.
The image is distorted or blurred. · Resolution of the image is too low. Try
playing a file with a higher resolution. 480
X 234 (RGB) is recommended.
Responds of the device is too slow There are too many files in the memory
device.
Technical Specifications
Item Description
Display 7.0-inch LCD screen
USB Interface USB 2.0 Host(High Speed)
Photo Format JPEG
Supported Memory Card SD/MMC/MS
Image Resolution 480X234 pixel
Memory Card Capacity 4GB (MS/SD Up to 4GB, MMC Up to 2GB)
USB Flash Disk Up to 8GB
Power Supply AC Adapter, Input 100-240V, Output 5V
Storage Temp* -20℃～+55℃
Ambient Temp* 0℃～+55℃
Operation Relative Humidity* 20% ～90%（40℃）
Storage Relative Humidity* 20% ～93%（40℃）

ODYS DPF-Shine
EN
Warranty condition
The following conditions comprise the requirements and scope of our warranty conditions and do not
affect our legal and contractual warranty obligations.
We offer a warranty on our products in accordance with the following conditions:
1. Odys products are covered by a 24 month warranty. We will resolve damages or defects on Odys
products free of charge within 12 months of the purchase date under the following warranty
conditions. For any damage or defect determined later than 12 months after the purchase date,
proof of a manufacturing fault must be submitted for repair under warranty.
The warranty does not cover batteries and other parts, which are considered consumables, parts
that break easily such as glass or plastic or defects based on normal wear and tear. There is no
warranty obligation in the event of marginal differences compared to the target appearance and
workmanship provided these have a negligible effect on the product's fitness for use, in the event of
damage caused by chemical or electrochemical effects, by water or generally from abnormal
conditions.
2. The warranty will be performed in such a way that we shall decide whether to repair the defective
parts or to replace them with working parts free of charge. AXDIA reserves the right to exchange
the product for a replacement product of equal value if the product that is sent in cannot be repaired
within a reasonable time or at reasonable cost. The product can also be exchanged for a different
model of the same value. Requests cannot be made for repairs to be carried out on site. Parts that
have been replaced or exchanged become our property.
3. The warranty claim does not apply if repairs or other work is carried out by unauthorized persons
or if our products are equipped with additional parts or accessories that are not approved for our
products.
4. Warranties that have been activated do not cause the warranty period to be extended, nor do they
trigger a new warranty period. The warranty period for any replacement parts installed ends with the
warranty period for the entire product.
5. Any other or further claims are excluded, especially those for replacement due to damage caused
outside of the product, provided there is no obligatory legal liability. We therefore accept no liability
for accidental, indirect or other consequential damage of any kind, which leads to usage
restrictions, data loss, loss of earnings or interruption to business.
Asserting a warranty claim
1. To make use of the warranty service, you must contact the AXDIA Service Center by e-mail, fax or
phone (see below for contact details). You can also use the service form on our website or on the
back of the warranty conditions.
2. AXDIA Service Center will try to diagnose and solve your problem. If it is determined that a
warranty claim exists, you will be given an RMA number (Return Material Authorization) and you will
be asked to send the product to AXDIA.
IMPORTANT: AXDIA will only accept parcels that have an RMA number.
Please observe the following when sending the product:
1. Send the product suitably packaged with carriage and insurance paid. Do not enclose any
accessories with the products (no cables, CD's, memory cards, manuals, etc.), unless the AXDIA
Service Centre specifies otherwise.
2. Mark the RMA number on the outside of the package in such a way that it is visible and clearly
legible.
3. You must enclose a copy of the sales slip as proof of purchase.
4. Once AXDIA has received the product, it will meet its warranty obligations in accordance with the
warranty conditions and will return the product to the sender with carriage and insurance paid.
Service outside of warranty
AXDIAcan refuse any service claim made that is not covered by the warranty. If AXDIA agrees to
provide a service outside the warranty, the customer will be invoiced for all repair and transport costs.
AXDIA will not accept any packages that have not first been approved byAXDIA by means of an RMA
(Return Material Authorization).