OEM Tools Cut-40 Service manual

UNPACKING
After unpacking the unit, inspect carefully
for any damage that may have occurred
during transit. Check for loose, missing, or
damaged parts. If any damage is observed, a
shipping damage claim must be filed with the
carrier. DO NOT use the OEMTOOLS™24814
Plasma Cutter if broken, bent, cracked or
damaged parts (including labels) are noted.
Any Plasma Cutter that appears damaged in
any way, operates abnormally or is missing
parts should be removed from service
immediately. If you suspect that the Plasma
Cutter was subjected to shock load (a load
that was dropped suddenly, unexpectedly,
etc.), immediately discontinue use until it
has been checked by a factory authorized
service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and
others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal
injury and/or damage to product or property. Please retain instructions for future reference.
The following safety information is provided as a guideline to help you operate your Plasma Cutter under the safest possible
conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are
not known or not followed. The following safety instructions are to provide the user with the information necessary for safe
use and operation. Please read and retain these instructions for the continued safe use of your Plasma Cutter. Failure to follow
instructions listed below may result in serious injury. In addition, make sure that anyone who uses the equipment understands
and follows these safety instructions as well.
Operating Instructions and Parts Manual 24814
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
Thank you very much for choosing an OEMTOOLS™Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product
before you begin using it. This product is designed for certain applications only. OEMTOOLS™cannot be responsible for issues
arising from modification. We strongly recommend this product is not modified and/or used for any application other than that for
which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first
contacted customer service to determine if it can or should be performed on the product.
Explanation of Safety Signal Words
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result
in property damage.
NOTES:Provide clarity and helpful information.
PLASMA CUTTER
110/220V 40 AMP
1
2/18
2018 OEMTOOLS™
WARNING

2
Operating Instructions and Parts Manual 24814
2/18
2018 OEMTOOLS™
PLASMA CUTTER
110/220V 40 AMP
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your product. Read this manual carefully. Learn
the product’s applications and limitations, as well as
potential hazards specific to it.
2. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.
3. Keep children away. All children should be kept away
from the work area. Never let a child handle tools or
equipment without strict adult supervision.
4. DO NOT operate this product if under the influence of
alcohol or drugs. Read warning labels on prescriptions
to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, DO NOT
attempt to operate.
5. Use safety equipment. Eye protection should be
worn at all times when operating this tool. Use ANSI
approved safety glasses. Everyday eyeglasses are
NOT safety glasses. Dust mask, non-skid safety
shoes, hard hat or hearing protection should be used
in appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties,
rings, bracelets or other jewelry may present a potential
hazard when operating this product. Keep all apparel
clear of the product.
7. DO NOT overreach. Keep proper footing and balance
at all times when operating this product.
8. Check for damage. Check equipment regularly. If
part of the product is damaged, it should be carefully
inspected to make sure that it can perform its
intended function correctly. If in doubt, discontinue
use of product.
9. Keep away from flammables. DO NOT attempt to
operate this product near flammable materials or
combustibles. Failure to comply may cause serious
injury or death.
10. Store this product out of the reach of children and
untrained persons. This product may be dangerous in
the hands of untrained users.
11. Keep this product dry and clean.
12. Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one product may become hazardous when
used on another product.
13. Service must be performed only by qualified repair
personnel. Service or maintenance performed by
unqualified personnel could result in a risk of injury.
14. When servicing a product, use only identical replacement
parts. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of injury.
15. Maintain a safe working environment. Keep the work
area well lit. Make sure there is adequate surrounding
workspace. Keep the work area free of obstructions,
grease, oil, trash, and other debris. Do not use this
product in a damp or wet location.
16. Maintain labels and nameplates on this product. These
carry important information. If unreadable or missing,
contact OEMTOOLS™for a replacement.
17. Keep this product dry, clean, and free from brake fluid,
oil, and grease.
18. Avoid accidental fire. DO NOT smoke near this product.
19. The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions
and situations that may occur. The operator must
understand that common sense and caution are factors
which cannot be built into this product, but must be
supplied by the operator.
20. We believe the information contained herein to be
reliable. However, general technical information is given
by us without charge and the user shall employ such
information at their own discretion and risk. We assume
no responsibility for results or damages incurred from
the use of such information in whole or in part.
21. The manufacturer declines any and all responsibility
for property damage or injury if said damage is the
result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
22. The procedures documented in this manual are to
serve as guidelines for the use of this equipment.
23. The use of this equipment is simple and straightforward
if you follow the instructions. When operating this
equipment, use common sense, and only use this
equipment for its intended purpose.
PRODUCT DESCRIPTION
The OEMTOOLS™24814 Plasma Cutter cuts mild steel,
copper, brass, stainless steel and aluminum. This portable
Plasma Cutter is compatible with 110V and 220V AC power.
PRODUCT SPECIFICATIONS
Input Voltage 110V AC / 220V AC
Input Current 20A /28A
Input Frequency 60Hz
Rated Duty Cycle 60% @ 30A (110V);
60% @ 40A (220V)
Output Current Range 20-40A
Output Voltage 96V DC
Gas Required Compressed Air
Air Requirements 60-70 PSI
Plasma Cutter Weight 26.5 Lbs.
CONTENTS
(1) Plasma Cutter, (1) Plasma Torch, (1) Ground Cable with
Clamp, (1) 110V Adapter Cord, (1) Protective Face Mask
with Lens and (1) Chipping Hammer/Brush
GENERAL CUTTING SAFETY AND
INSTRUCTIONS
WARNING:Thoroughly read and understand the
provided product manual before attempting to use
this product.
WARNING:PLASMA CUTTING CAN BE DANGEROUS.
1. DO NOT allow untrained persons or children to operate.
Ensure people in the surrounding area understand
the dangers and precautions associated with plasma
cutting prior to use.

3
Operating Instructions and Parts Manual 24814
2/18
2018 OEMTOOLS™
PLASMA CUTTER
110/220V 40 AMP
2. CONSULT WITH A PHYSICIAN PRIOR TO OPERATION
IF YOU HAVE A PACEMAKER. Plasma Cutters create
an Electromagnetic Field (EMF) which can interfere with
pacemakers. These High Frequency (HF) waves may
disturb other sensitive electronic equipment.
3. DO NOT attempt to perform repairs on this product.
WARNING:PLASMA CUTTING PRODUCES ARC
AND UV RAYS THAT CAN BURN SKIN AND CAUSE
EYE DAMAGE.
1. Signs should be posted within the workspace stating
hazards and precautions associated with plasma
cutting and related protection.
2. The operator and nearby personnel located in the
workspace should wear protective shields conforming
to ANSI standards, with the proper filter and cover
plates to protect eyes from sparks and arc rays.
3. The operator and nearby personnel located in the
welding workspace should wear protective clothing
made with flame-resistant material to protect skin from
sparks, metal and arc rays.
WARNING:PLASMA CUTTING PRODUCES
ELECTROMAGNETIC FIELDS. THESE FIELDS ARE
DANGEROUS AND CAN CAUSE SERIOUS INJURY OR
DEATH IF PRECAUTIONS ARE NOT FOLLOWED.
1. Plasma Cutting current creates an Electromagnetic
Field (EMF) around the machine, leads and cords.
EM fields interfere with some pacemakers (as stated
previously), and prolonged exposure to EM fields may
have other health effects that are undetermined. Before
operating this product, the operator and personnel
located within the workspace should understand that
there are health risks (determined and undetermined)
associated with arc rays and EM fields.
2. MINIMIZE EXPOSURE TO EM FIELDS BY EMPLOYING
THE FOLLOWING PRECAUTIONS:
a. DO NOT place your body between the electrode
and the work cables.
b. DO NOT coil or wrap the leads around any part of
the body.
c. DO NOT SEPARATE work cables and leads. Route
and secure the cables together.
d. DO NOT work/cut directly beside the power source.
e. Ensure the ground cable is connected to the
workpiece as close to the cut as possible.
WARNING:SPARKS CAN CAUSE FIRE AND
EXPLOSION, WHICH CAN LEAD TO INJURY, DEATH
AND PROPERTY DAMAGE. ALWAYS HAVE A FIRE
EXTINGUISHER WITHIN THE WORK AREA AND
IMPLEMENT A FIRE ESCAPE PLAN.
1. Remove all flammable items and potential fire hazards
from the workspace. If there are fire hazards that
cannot be removed, these should be covered with a
fire-resistant cover.
2. DO NOT operate near hydraulic, fuel or natural gas lines.
3. DO NOT operate near flammable gases, residue or
greases. Take proper steps to ventilate and clean
workspace prior to use.
4. DO NOT operate near compressed gases. DO NOT
heat, cut or weld tanks, drums or other containers that
may have stored flammable gases or liquids. While
these tanks may be “empty”, residue will remain that
could lead to fire or explosion.
5. It is imperative that the operator and personnel located
within the workspace wear oil-free, flame-resistant
clothing. Clothing should provide full coverage: heavy
leather gloves, long-sleeve shirt, full length pants (no
cuff), high protective leather boots and a welding cap
that covers all hair. Clothing should be well fitted;
loose fitting clothing may create a fire hazard. When
operating in confined spaces, flame-resistant earplugs
or earmuffs should be worn.
6. DO NOT connect the work cable to building
framework. Connect the Ground Clamp to work as
close the cut as possible.
7. All cylinders should be securely stored in an upright
position away from workspace. Plasma cutting can
project sparks and debris that may strike cylinders.
DO NOT allow the machine, Ground Cable or Torch to
contact a cylinder. Prior to cutting, ensure the valves on
all cylinders in the vicinity are closed.
8. ALWAYS check the workpiece and surrounding work
area for smoke, flame, sparks or evidence of fire.
WARNING:ELECTRIC SHOCK CAN KILL. DO NOT
TOUCH Torch, WORK OR GROUND WHILE THE PLASMA
CUTTER IS PLUGGED INTO A POWER SOURCE.
1. DO NOT wear wet clothing or gloves.
2. DO NOT place the electrode in water.
3. DO NOT allow components of (2) Plasma Cutters to
come into contact while either machine is plugged into
a power source.
4. ALWAYS connect to a grounded, GFCI-protected
power supply.
5. ALWAYS insulate yourself from the workpiece and
ground. Non-flammable, dry insulating material is
recommended.
6. Install and ground equipment in accordance with the
US National Electrical Code, local codes and according
to this instruction/installation manual.
7. Ensure the Ground Clamp is properly connected to the
metal being cut.
8. Ensure that all welding equipment and leads are well
maintained and in safe operating condition prior to
each use.
WARNING:PLASMA CUTTING MAY PRODUCE
FUMES AND GASES THAT ARE HAZARDOUS TO THE
HEALTH OF THE OPERATOR AND PERSONNEL LOCATED
WITHIN THE WELDING WORKSPACE. EXPOSURE
TO THESE FUMES CAN INCREASE THE RISK OF
DEVELOPING CANCER, HEART DISEASE, EARLY ONSET
PARKINSON’S DISEASE AND VARIOUS REPRODUCTIVE,
RESPIRATORY AND DIGESTIVE DISEASES.
1. DO NOT place your head near the cutting arc; avoid
breathing fumes while cutting. Ensure proper ventilation.

4
Operating Instructions and Parts Manual 24814
2/18
2018 OEMTOOLS™
PLASMA CUTTER
110/220V 40 AMP
2. Cutting hard-facing, galvanized, stainless and other
plated steels or metals produces highly toxic fumes.
Always read the MSDS for the product, metal or work
prior to cutting. Exhaust, mechanical ventilation and
a respirator may be required for minimal exposure to
these fumes.
3. Cylinders and containers that may have held harmful
gases should be properly vented prior to cutting.
Failure to ventilate these containers will produce toxic
gases that are harmful to the operator and all personnel
located within the workspace.
4. DO NOT cut near chlorinated hydrocarbons from
degreasing, cleaning or spraying operations.
5. Read and understand the product instructions and
MSDS sheet for any consumables or products used in
conjunction with this product. There are risks outside
of the operation of this product that can cause unsafe
working conditions.
SPECIFIC SAFETY INSTRUCTIONS
1. DO NOT connect to power while assembling or
performing maintenance on this unit.
2. DO NOT attempt to use if the unit fails to switch
ON or OFF.
3. DO NOT exceed the Rated Duty Cycle (see page 5),
4. ALWAYS ensure the Power is in the OFF position
prior to plugging the unit into a power source.
5. ALL INSTALLATION AND REPAIR OF THIS
EQUIPMENT SHOULD BE PERFORMED BY A
QUALIFIED TECHNICIAN IN ACCORDANCE WITH
FEDERAL, STATE AND LOCAL CODES.
INTRODUCTION TO PLASMA CUTTING
Plasma – Channel of superheated, electrically ionized gas.
Plasma Arc Cutting – Compressed air is pushed
through a focused nozzle directed toward an electrically
conductive workpiece. An electrical arc is formed within
the gas, between an integrated electrode (within the
nozzle of the Torch) and the workpiece. Electricity from
the Torch travels through the plasma to heat and melt
the workpiece. The plasma blows the melted metal away
from the workpiece, creating separation.
NOTE: Plasma cutting is used to create controlled
separation of material, at a specified/focused depth
and width.
ASSEMBLY INSTRUCTIONS
WARNING:Read all warnings and safety instructions
prior to installing this product.
1. Unpack all items from the box and reference the parts
list to ensure all parts are present before continuing
assembly.
2. Place the Plasma Cutter onto a clean, protected
surface that can support the weight of the Plasma
Cutter. Ensure the Plasma Cutter is placed at a
distance that will not overextend the cord or place
tension on the plug.
3. The Plasma Cutter can be plugged into a properly
grounded 110V AC or 220V AC outlet. When
connecting to a 110V AC power source, the 110V
adapter must be used.
POWER REQUIREMENT 110V:
DO NOT attempt to operate this unit if the power source
voltage is less than 110V AC or greater than 130V AC.
POWER REQUIREMENT 220V:
DO NOT attempt to operate this unit if the power source
voltage is less than 215V AC or greater than 240V AC.
NOTE: It is recommended that an extension cord not be
used with this Plasma Cutter; the voltage drop can affect
cutting performance.
4. The Plasma Torch is preassembled. Connect the
Plasma Torch to the Plasma Cutter.
5. Connect the Ground Cable/Clamp to the
Plasma Cutter.
6. Connect to a compressed air source (air
requirements: 60-70 PSI). It is highly recommended
to use a moisture removing filter between
compressor and the Plasma Cutter.
NOTE: Check the cylinder valves and connection points
for any oil, grease, dirt or debris.
OPERATING INSTRUCTIONS
NOTE: These instructions describe very basic processes
as they apply to the operation of this Plasma Cutter.
There are many different types of Plasma Cutters and
cutting procedures that cannot be described in detail
by this instruction manual. Proficiency in plasma cutting
requires practice, education and testing. DO NOT rely
solely on this product manual for instructions on proper
plasma cutting technique. By using this product, the
operator understands that OEMTOOLS™cannot be held
responsible for property damage caused by operator
negligence, ignorance or general mistakes..
NOTE: After reading through this manual, it is
recommended that the operator, despite experience level,
practice cutting scrap metal with this Plasma Cutter.
General operation and performance will vary by model.
1. Thoroughly read the Assembly Instruction Section and
complete product installation.
2. Connect the Ground Clamp to a clean, bare metal
surface on the workpiece. If necessary, use the wire
brush to scrape/file any paint or residue from the
surface of the workpiece to achieve a proper ground.
WARNING:Thoroughly read warnings regarding
electric shock and fire hazards prior to this step.
3. Switch the Power to ON.
4. Set the air pressure within the recommended range
(60-70 PSI). Higher air pressure is needed to cut
thicker/harder metals, lower air pressure is needed to
cut thinner metals.
5. Set the output amperage to the desired setting. Higher
amperage is needed to cut thicker/harder metals, lower
amperage is needed to cut thinner metals.
WARNING:DO NOT attempt to operate the Plasma

5
Operating Instructions and Parts Manual 24814
2/18
2018 OEMTOOLS™
PLASMA CUTTER
110/220V 40 AMP
Cutter without the proper protective equipment.
Reference the safety instructions prior to attempting use.
6. Hold the Plasma Torch within 1/8" of the workpiece and
press Trigger. This will initiate the cutting arc.
7. Move the Plasma Torch across the workpiece at a slow,
controlled pace.
8. When the cut is complete, release the trigger and
remove from the workpiece.
9. Switch the Power to OFF.
10. Unplug the Power Cord from the Power Source.
Torch ELECTRODE AND TIP REPLACEMENT
INSTRUCTIONS
WARNING:Turn off the Plasma Cutter and unplug
from the power source before servicing Torch.
WARNING:Allow Torch to cool sufficiently after use
before attempting to service.
NOTE: The Torch head assembly consists of an
Electrode, Diffuser, Tip and Shield Cup.
NOTE: The Electrode and Tip are consumable items and
will need to be replaced periodically.
1. Rotate the Shield Cup counterclockwise until the unit is
released from the Torch head.
2. Remove the Tip from the Electrode and Diffuser.
Replace if needed.
3. Remove the Diffuser from the Electrode. Replace if needed.
4. Remove the Electrode from the Torch. Replace if needed.
5. Reassemble prior to use.
CAUTION:DO NOT overtighten the Shield Cup. The
Shield Cup thread is designed to leave a gap between
the Shield Cup and the Torch head assembly to release
gas. Overtightening the Shield cup can cause irreparable
damage to the internal components of the Torch.
DUTY CYCLE
To avoid product damage and personal injury, DO NOT cut
for longer than the prescribed Duty Cycle Time. This Plasma
Cutter has a 60% Duty Cycle Time at 30A (110V) and
60% Duty Cycle Time at 40A (220V). At either voltage, this
Plasma Cutter can cut for 6 seconds out of every 10 second
time period. Failure to comply may lead to product failure.
HELPFUL TIPS
1. Thoroughly clean surfaces prior to cutting. Brush or
sand off all paint, adhesive and oxidation.
2. Higher air pressure is needed to cut thicker/harder metals,
lower air pressure is needed to cut thinner metals.
3. Higher amperage is needed to cut thicker/harder metals,
lower amperage is needed to cut thinner metals.
4. Cut speed will affect quality and cut finish. During the
cutting process, dross (build-up of molten material
around the cut area) will occur depending on the
cutting speed and operator experience/ability.
a. Top Dross – Occurs when the Torch is held too
far from the workpiece. This can be wiped away
using a Welding Glove.
b. Slow Speed Dross – A bead that collects at the
bottom edge of the cut. This bead can be easily
removed by scraping.
c. High Speed Dross – A narrow bead that collects at
the bottom edge of the cut. This bead is difficult to
remove, and requires a grinder.
STORAGE
WARNING:Always turn OFF and unplug before
placing into storage.
Store the Plasma Cutter in an upright position and in a
clean, dry area. DO NOT store near flammable items or
open flames.
PRODUCT MAINTENANCE
WARNING:DO NOT attempt to repair this product.
Contact qualified service personnel.
WARNING:Always turn OFF and unplug this Plasma
Cutter before attempting product maintenance.
1. Wipe dust, grease and debris from the Plasma Cutter
casing before and after each use.
WARNING:DO NOT use water.
2. Evaluate the machine for any issues that may hinder the
machine or accessories from performing in accordance
with proper operation. If any issues are noted, DO NOT
attempt to use. Contact customer service.
3. Check the Torch Tip and Electrode for wear that may
impede the use of this unit. Wipe away any dirt, dust or
debris using a dry, clean cloth.
4. Check the Torch and cables for any signs of wear. If
any damage is noted, discontinue use and contact
customer service.
DISPOSAL
At the end of the useful life of the OEMTOOLS™24814
Plasma Cutter, dispose of the components in accordance
with all federal, state and local regulations.

6
Operating Instructions and Parts Manual 24814
2/18
2018 OEMTOOLS™
PLASMA CUTTER
110/220V 40 AMP
TROUBLESHOOTING
Problem Possible Cause Possible Solution
No cutting output, power light is off No power is supplied to the unit
Ensure the power cord is plugged in
Check the power cord and plug for
damage
Reset circuit breaker
No cutting output, power light is on
No airflow Check air connection and airflow
output
Faulty Ground Clamp and Torch
connection Check Clamp and Torch connections
Faulty or incorrect tip is used Review Cutting Tip installation and
maintenance instructions
Plasma Cutter has malfunctioned Discontinue use and contact
customer service
Insufficient cutting
Workpiece thickness exceeds safe
cutting practices for this unit Discontinue use immediately
Insufficient power supply Check power supply; contact a
certified electrician
Torch is moved too quickly Reduce cutting speed
Airflow is too low Increase airflow
Amperage is set too low Increase amperage settings
Moisture in Torch
Hold Torch above clean surface and
allow to purge (DO NOT pull Trigger,
as this will initiate arcing)
Cutting is causing excessive metal
spatter and sparking
Amperage is set too high Decrease amperage settings
Airflow is too high Decrease airflow
No output from Torch
Airflow is too low Increase pressure to the
recommended range
Faulty Torch Contact customer service
Faulty components in Plasma Cutter Contact customer service
Arc ceases while the Trigger is
pressed
Power supply has overheated Unplug, let cool and restart
Unit has overheated Unplug, let cool and restart (reference
the Duty Cycle Time for further detail)
Faulty or incorrect tip is used Review cutting tip installation and
maintenance instructions
Airflow is too low Increase pressure to the
recommended range

7
Operating Instructions and Parts Manual 24814
2/18
2018 OEMTOOLS™
PLASMA CUTTER
110/220V 40 AMP
B
A
C
D
E
F
G
I
H
K
J
Figure Description Qty.
A Plasma Cutter 1
B Handle 1
C Air Pressure Gauge 1
D Amperage Setting 1
E Power Switch 1
F Air Pressure Setting 1
G 110V/220V Adapter 1
H Torch 1
I Torch Nozzle Assembly 1
J Ground Cable with Clamp 1
K Chipping Hammer/Brush 1
L Power Cord* 1
M Protective Face Mask and Lens* 1
PARTS DESCRIPTION
*Not Shown
PRODUCT LAYOUT

8
Operating Instructions and Parts Manual 24814
2/18
2018 OEMTOOLS™
PLASMA CUTTER
110/220V 40 AMP
CONTACT US
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS™One Year Warranty
For up to one year from the date of purchase of this OEMTOOLS™product, if you find any defect in material or
workmanship (through normal usage), return it to the place of purchase or to OEMTOOLS™for repair or replacement at
our discretion. In order to obtain this service, send the product and proof of purchase (transportation pre-paid) to:
OEMTOOLS™Q.A. Dept, 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our
inspection verifies the defect, we will either repair or replace the product, or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if
we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you
must bear the cost of returning the product.
OEMTOOLS™does not provide warranty for products labeled other than OEM®or OEMTOOLS™. OEMTOOLS™will
not provide any warranty for products subjected to abnormal use. Abnormal use includes (but is not limited to) abuse,
accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not cover bits,
blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace blades, bits,
files, and batteries as necessary. OEMTOOLS™reserves the right to make any changes in construction or design at
any time without any obligation in incorporating such changes to tools or equipment previously sold. OEMTOOLS™
makes every effort to ensure that its products meet high quality and durability standards, and warrants to the original
purchaser that this product is free from defects in materials and workmanship for the period of one year from the
date of purchase. This warranty does not apply to damage due directly or indirectly to misuse, abuse, negligence or
accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear or to
lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state.
Don’t forget to register your new OEMTOOLS™product at www.oem-tools.com.