Oem Vkp80iii User manual

OEM

Commands manual

77200000000200

VKP80III

USER MANUAL

The format used for this manual improves use of natural resources reducing the quantity of necessary paper to print this

copy.

CUSTOM ENGINEERING S.p.A.

Str. Berettine 2

43010 Fontevivo (PARMA) - Italy

Tel. : +39 0521-680111

Fax : +39 0521-610701

http: www.custom.biz

Customer Service Department:

Email : [email protected]

reproduction of this manual in whatever

form, whether by printed or electronic

means, is forbidden. While guaranteeing

that the information contained in it has

been carefully checked, CUSTOM ENGI-

NEERING S.p.A. and other entities utilized

in the realization of this manual bear no

responsibility for how the manual is used.

Information regarding any errors found in it

or suggestions on how it could be improved

are appreciated. Since products are sub-

ject to continuous check and improvement,

CUSTOM ENGINEERING S.p.A. reserves

the right to make changes in information

contained in this manual without prior

notiﬁcation.

The pre-installed multimedia contents

are protected from Copyright CUSTOM

ENGINEERING S.p.A. Other company

and product names mentioned herein

may be trademarks of their respective

companies. Mention of third-party products

is for informational purposes only and

constitutes neither an endorsement nor a

recommendation. CUSTOM ENGINEER-

ING S.p.A. assumes no responsibility with

regard to the performance or use of these

products.

THE IMAGES USED IN THIS MAN-

UAL ARE USED AS AN ILLUSTRA-

TIVE EXAMPLES. THEY COULDN’T

REPRODUCE THE DESCRIBED

MODEL FAITHFULLY.

UNLESS OTHERWISE SPECIFIED,

THE INFORMATION GIVEN IN THIS

MANUAL

ARE REFERRED TO ALL MODELS

IN PRODUCTION AT THE ISSUE

DATE OF THIS DOCUMENT.

GENERAL SAFETY INFORMATION

Your attention is drawn to the following

actions that could compromise the char-

acteristics of the product:

• Read and retain the instructions which

follow.

• Follow all indications and instructions

given on the device.

• Make sure that the surface on which

the device rests is stable. If it is not, the

device could fall, seriously damaging it.

• Make sure that the device rests on a hard

(non-padded) surface and that there is

sufﬁcient ventilation.

• When positioning the device, make sure

cables do not get damaged.

• Use the type of electrical power supply

indicated on the device label. If uncer-

tain, contact your dealer.

• Make sure the electrical system that

supplies power to the device is equipped

with a ground wire and is protected by a

differential switch.

• Do not block the ventilation openings.

• Do not insert objects inside the device as

this could cause short-circuiting or dam-

age components that could jeopardize

printer functioning.

• Do not carry out repairs on the device

yourself, except for the normal main-

tenance operations given in the user

manual.

• Make sure that there is an easily-acces-

sible outlet with a capacity of no less

than 10A closely to where the device is

to be installed.

• Periodically perform scheduled mainte-

nance on the device to avoid dirt build-up

that could compromise the correct, safe

operation of the unit.

• Before any type of work is done on the

machine, disconnect the power supply.

• Do not touch the head heating line with

bare hands or metal objects. Do not

perform any operation inside the printer

immediately after printing because the

head and motor tend to become very

hot.

GENERAL INSTRUCTIONS

CUSTOM ENGINEERING S.p.A. declines

all responsibility for accidents or damage

to persons or property occurring as a re-

sult of tampering, structural or functional

modiﬁcations, unsuitable or incorrect in-

stallations, environments not in keeping

with the equipment’s protection degree or

with the required temperature and humidity

conditions, failure to carry out maintenance

and periodical inspections and poor repair

work.

THE CE MARK AFFIXED TO

THE PRODUCT CERTIFY

THAT THE PRODUCT SAT-

ISFIES THE BASIC SAFETY

REQUIREMENTS.

The device is in conformity with the es-

sential Electromagnetic Compatibility and

Electric Safety requirements laid down in

Directives 2006/95/CE and 2004/108/CE

inasmuch as it was designed in conformity

with the provisions laid down in the follow-

ing Standards:

• EN 55022 Class B (Limits and methods

of measurements of radio disturbance

characteristics of Information Technol-

ogy Equipment)

• EN 55024 (Information Technology

Equipment – Immunity characteristics –

Limits and methods of measurement)

• EN 60950-1 (Safety of information

equipment including electrical business

equipment)

GUIDELINES FOR

THE DISPOSAL OF

THE PRODUCT

The crossed-out rubbish bin logo means

that used electrical and electronic products

shall NOT be mixed with unsorted munici-

pal waste. For more detailed information

about recycling of this product, refer to the

instructions of your country for the disposal

of these products.

• Do not dispose of this equipment as

miscellaneous solid municipal waste, but

arrange to have it collected separately.

• The re-use or correct recycling of the

electronic and electrical equipment

(EEE) is important in order to protect

the environment and the wellbeing of

humans.

• In accordance with European Directive

WEEE 2002/96/EC, special collection

points are available to which to deliver

waste electrical and electronic equip-

ment and the equipment can also be

handed over to a distributor at the mo-

ment of purchasing a new equivalent

type.

• The public administration and producers

of electrical and electronic equipment

are involved in facilitating the processes

of the re-use and recovery of waste elec-

trical and electronic equipment through

the organisation of collection activities

and the use of appropriate planning ar-

rangements.

• Unauthorised disposal of waste electrical

and electronic equipment is punishable

by law with the appropriate penalties.

1 INTRODUCTION.................................................................................................................................................... 7

1.1 Document structure...................................................................................................................................... 7

1.2 Explanatory notes used in this manual ........................................................................................................ 7

2 DESCRIPTION....................................................................................................................................................... 9

2.1 Unpacking the device................................................................................................................................... 9

2.2 Device component ..................................................................................................................................... 10

2.3 Key functions.............................................................................................................................................. 14

2.4 Status led ﬂashes....................................................................................................................................... 16

3 INSTALLATION.................................................................................................................................................... 17

3.1 Fastening ................................................................................................................................................... 17

3.2 Connections ............................................................................................................................................... 18

3.3 Pinout ......................................................................................................................................................... 20

3.4 Driver.......................................................................................................................................................... 22

4 OPERATION ........................................................................................................................................................ 23

4.1 Adjusting paper width................................................................................................................................. 23

4.2 Adjusting alignment sensors ...................................................................................................................... 24

4.3 Paper roll insertion ..................................................................................................................................... 27

4.4 Issuing ticket .............................................................................................................................................. 29

5 CONFIGURATION ............................................................................................................................................... 37

5.1 Conﬁguration mode.................................................................................................................................... 37

5.2 Setup report ............................................................................................................................................... 39

5.3 Printer status .............................................................................................................................................. 40

5.4 Printer parameters ..................................................................................................................................... 41

5.5 Hexadecimal dump .................................................................................................................................... 44

6 MAINTENANCE................................................................................................................................................... 45

6.1 Planning of cleaning operations ................................................................................................................. 45

6.2 Cleaning ..................................................................................................................................................... 46

6.3 Upgrade ﬁrmware....................................................................................................................................... 53

7 SPECIFICATIONS................................................................................................................................................ 55

7.1 Hardware speciﬁcations ............................................................................................................................. 55

7.2 Character speciﬁcations............................................................................................................................. 57

7.3 Ejector speciﬁcations ................................................................................................................................. 57

7.4 Printer dimensions ..................................................................................................................................... 58

7.5 Power supply dimensions cod.963GE020000003 (optional) ..................................................................... 59

7.6 Paper speciﬁcations ................................................................................................................................... 60

7.7 Western characters .................................................................................................................................... 61

8 CONSUMABLES ................................................................................................................................................. 69

9 ACCESSORIES ................................................................................................................................................... 71

9.1 Adapter cable for power supply.................................................................................................................. 72

9.2 Paper roll holder......................................................................................................................................... 73

9.3 Adjustable four position holder for paper roll (right and left side)............................................................... 78

9.4 “Shutter” device.......................................................................................................................................... 80

INDEX

User Manual VKP80III 5