OFFCARR EASY-BIKE User manual

1
EASY-BIKE & EASY-BIKE KID
Instruction Manual
2020.12

2
Thanks for choosing an OFFCARR product.
Since 1982 OFFCARR answers to the customers’ needs by developing highly
innovative and technologic solutions, always aimed to reduce daily mobility
problems, with special attention to product style and to improve customers’ life
quality.
OFFCARR has a certified system for quality management following UNI EN ISO
9001:2015 regulations and a Medical device - Quality management system following
UNI EN ISO 13485:2016 regulations.
OFFCARR products meet the 93/42/CEE directives, upgraded with the 2007/47/CE
directive.
Before using or making adjustments on this device, carefully read the content of this
instruction manual.
If needed, please contact an authorized dealer or the manufacturer at the following
address:
OFF CARR S.r.l.
Via dell’Artigianato II, 29
35010 Villa del Conte (Padova) Italy
Tel. [phone] – Fax [phone]
e-mail: offcarrffcarr.com – http://www.offcarr.com

3
Introduction
EASYBIKE is a non-invasive medical device,
designed and manufactured to
compensate or attenuate a physical
handicap. The use of the bike or its
components is forbidden for any purposes
other than those indicated.
Description
Easybike is a unicycle which can be fitted
to any wheelchair with not detachable
foot-rests. It has a light steel alloy frame, designed to manually pull the wheelchair
by the user, using the driving force exercised by his arms on the drive handles.
The frame is available in different colours.
Thanks to the adjustable arms, is possible to adapt the device to be connected to
every wheelchair seat width and is possible to reach the most convenient distance
and inclination of the device for the best driving position (See pictures below).
For very narrow wheelchairs, adjustable arms are available with shorter
attachments than normal models.

4
PACCO PIGNONI A 9 RAPPORTI GUARNITURA A 3 RAPPORTI PINZA FRENO COMANDI CAMBIO
GUARNITURA PIGNONE
9 SPEED SPROKET 3 SPEED CRANK SET CALIPER BRAKE HANDLE SHIFT CONTROLS
CRANK SET SPROKET

5
Features
There are different Easybike models:
oEASYBIKE-27: 27-gear with dual gear shifting units and double wire brake
levers.
oEASYBIKE-8F & EASYBIKEKID-8F: 8-gear built-in hub with Thumb Control
shifting unit or Revoshift and single wire lever.
oEASYBIKE-8CR & EASYBIKEKID-8CR: 8-gear built-in hub with Revoshift
control and coaster brake.
The 27-gear shift model is fitted with a 9 speed sprocket on a 24” wheel and 3 speed
crank sets, controlled by two thumb control shifting units on the pushing handles.
The two wire brake levers, as well mounted on the pushing handles, act
independently onto the same caliper brake.
The model with 8-gear built-in hub on a 24” wheel has the speed control mounted
on the pushing handles as well the brake lever.
The model with 8-gear built-in hub with integrated coaster brake assembled on a
24” wheel has the Revoshift speed control on a pushing handle (right or left). The
bike is braked by pushing backward the cranks.
The Kid model is supplied with a 20” mountain-bike wheel in place of a 24” high
pressure wheel.
All models are supplied with front light, bell, and adjustable stands. The Easybike
can be optionally equipped with quadriplegic handles (model F or H), cyclo-
computer, rear-view mirror and an additional red light to be connected on the back
of the wheelchair.
MOZZO CON CAMBIO INTEGRATO COMANDO A 8 RAPPORTI COMANDO REVOSHIFT MOD. H MOD. F
CON LEVA FRENO MANIGLIE PER TETRA
8-GEAR BUILT-IN HUB THUMB CONTROL SHIFTING REVOSHIFT CONTROL QUADRIPLEGIC HANDLES

6
Preparation for use
The Easybike is supplied configured according with the order form selection to
ensure the most convenient setup to match the customer needs. In order to be
properly connected to a specific wheelchair, therefore, some additional adjustments
may be required.
Please follow this manual instructions perform the final set-up of the device to
match your wheelchair.
Matching the EASYBIKE with the wheelchair
Before matching the Easybike with the wheelchair consider that you can modify the
position of the fastening pipe and adjust the position of the fastening clamp.
If necessary, loosen the clamp by opening the cam lever to adjust the fixing tube.
Pull out the tube and place it on the chosen spot. Once placed it lock the clamp by
closing the cam lever.

7
If necessary adjust the clamp rotation in the following way:
oLoosen the highlighted nuts (as in the picture)
oRotate the clamp in the chosen position
oFa sten the nuts
Nuts

8
Once the clamp is placed on the chosen position proceed as follows:
oLoosen the fixing clamp of the fastening clamp
oExtend the spring release lever

9
oRotate the clamp and place it on the optimal angle for the wheelchair
fastening

10
Stand the Easybike on the proper stands in front of the wheelchair.
oPlace the wheelchair front tubes very close to the Easybike fastening
clamps.
oMake sure the fastenings clamps are open.
oMake sure the latch is off.
oMake sure the fastening clamps are perfectly matching the wheelchair front
frame tubes and eventually, adjust the clamps position, if needed.