OfficeMaster YES Series User manual

2009 Wright Avenue La Verne, CA 91750 Tel: [phone] Fax: [phone]
Page | 1 www.officemaster.com
PRODUCT SPECIFICATIONS
MODEL: YS70N
DESCRIPTION: Mesh Nesting Chair
OVERALL DIMENSIONS
Overall ht 37”
Overall Width 24.5”
Overall Depth 24”
Seat Height 18”
Seat Width 18”
Seat Depth 18”
Back Width 20”
Back Height 20”
Weight (lb) 29
KEY COMPONENTS
Back Reinforced nylon frame,
Upholstered in mesh
Seat Contoured molded foam
Frame Black powder coated steel tube
1”dia. X 15+guage thick
PACKING: Ships with Back detached and (1) Allen Bolt + (1) Allen
Wrench for simple assembly. 1 chair / box
UPS shipping weight: ~85 lbs.

2009 Wright Avenue La Verne, CA 91750 Tel: [phone] Fax: [phone]
Page | 2 www.officemaster.com
YS70N Nesting Chair (YES Series)
Assembly Instructions
Thank you for your purchase of an Office Master YES Series Nesting Chair!
We sincerely believe that you’ll enjoy using your YS70N chair.
However, before you can do so, there are few easy steps that you’ll need to
follow in order to complete assembly of your chair. See below for details!
To save you cost on shipping, we’ve carefully packaged your YS70N in a special
shipping box with its back detached & all the tools needed for easy assembly.
1. When you receive your YS70N it will look like this.
2. When you open the box, here are the parts that you’ll find inside.
(1) Mesh Backrest
(1) YS70N Chair Frame & (1) Upholstered Seat Cushion
(1) Allen Bolt & (1) Allen Wrench

2009 Wright Avenue La Verne, CA 91750 Tel: [phone] Fax: [phone]
Page | 3 www.officemaster.com
3. To assemble your YS70N, remove the Allen Wrench from its plastic sleeve
and use it to remove the Allen Bolt from its current location in the metal
upright part at the top of the YS70N chair frame.
4. Once the Allen Bolt is removed, note the location of the screw hole that it was
originally in, and then proceed to the next steps (note that there are 2holes
at the top of the metal upright bar… the one you’ll want is the TOP hole).
5. Your next step is to insert the YS70N chair frame’s metal upright bar into the
Mesh Backrest through the opening shown below.
(A) Locate the opening in the Mesh Backrest…
(Step 5 continues on next page)…

2009 Wright Avenue La Verne, CA 91750 Tel: [phone] Fax: [phone]
Page | 4 www.officemaster.com
(…continuation of Step 5 from previous page)
(B)…Insert the metal upright into the Mesh Backrest…
(C)…Hold the Mesh Backrest with one hand and position
the backrest until you can see the TOP hole (as shown
in Step 4 above) in the YS70N’s metal upright bar
through the corresponding screw hole on the back and
in the center of the Mesh Backrest...
(Step 5 continues on next page)…

2009 Wright Avenue La Verne, CA 91750 Tel: [phone] Fax: [phone]
Page | 5 www.officemaster.com
(…continuation of Step 5 from previous page)
(D)…Using your free hand, insert the provided Allen Bolt
into place and hand-tighten until the Mesh Backrest
stays in place and doesn’t drop to the bottom of the
YS70N’s chair frame metal upright bar…
(E) …Now, use the provided Allen Wrench to firmly tighten
the Allen Bolt into place.
6. You’re FINISHED (and ready to enjoy your new Office Master YS70N
Nesting Chair!)