Officeworks SM2DRWFCWE User manual

Page 1 of 10
ASSEMBLY INSTRUCTIONS
MODEL#: SM2DRWFCWE
2 DRAWER FILE CABINET
This design and instruction booklet is subject to copyright.
www.officeworks.com.au

Tools Required For Assembly
Assemble Item On a Clean Flat Surface
Officeworks Superstores Pty Ltd. I 236-262 East Boundary Road I East Bentleigh I 3165 I AUSTRALIA
Recommend 2 Adults to Assemble
- Please check you have all hardware before assembling.
- If you think you are missing any hardware please contact the store of purchase.
- Please ensure you have the name of the item and hardware part required and quantity.
- Please retain your receipt for proof of purchase to validate warranty. Enjoy your new purchase.
Page 2 of 10
At least every 4 months, check all bolts, screws and knobs to be sure they are tight.
If parts are missing, broken, damaged or worn, stop use of the product until repairs are made,
using factory authorized parts.
Failure to follow these warnings could result in serious injury.
WARNING
.
.
.
.
Do not tighten the screws before all screws are in right place.
.Do not use this cabinet unless all bolts, screws and knobs are firmly secured.

Page 3 of 10
x1pc
PARTS LIST
HARDWARE LIST
1 2 3 4
56 7 8
910
A B C D
FG H I
K L
E
J
M N O
x8pcs x16pcs x12pcs x8pcs x16pcs
x2pcs x2pcs x2pcs x2pcs x4pcs
x2pcs x4pcs x8pcs x14pcs x4pcs
x1pc x1pc x1pc
x2pcsx2pcs x2pcs
x2pcs x2pcs
x2pcs

Page 4 of 10
Step 1
Step 2
B
x4pcs
A
x2pcs
F
FH
H
B
B
E
E
E
E
E
E
E
E
B
B
23
E
E
H
AA
A
C
C
C
2
5
5
E F H
x8pcs x2pcs x2pcs
x2pcs
C

Page 5 of 10
Step 3
Step 4
A
x2pcs
C
x2pcs
B
x4pcs
C
C
C
A
A
A
3
5
5
B
B
B
B
B
1

Page 6 of 10
Step 5
Step 6
N
x14pcs
x4pcs
O
A
A
A
A
A
C
C
C
C
1
2
3
A
x4pcs
C
x4pcs
XX=YY=90
。
N
O
O
O
O
4
3
2
4
XX
YY
N
N
Note: Partially hammer the nails 2/3
into back panel at this step for easy
removal. After the drawers are fully
aligned and travel smoothly, fully
hammer nails to inside back panel.

Page 7 of 10
Step 7
Step 8
D
x8pcs
B
B
B
B
B
B
6
x2
D
D
D
DD
6
7
9
x2
x8pcs
B
C
C
C
x4pcs
D

Page 8 of 10
Step 9
Step 10
10
x2
MM
MM
M
M
8
J
J
x2
M
x8pcs

Page 9 of 10
Step 11
Step 12 K
x2pcs
x2
I
9
7
G
E
E
E
E
E
E
l
K
L
L
6
x2
K
L
L
E
x8pcs
G
x2pcs
I
x2pcs
L
x4pcs

Page 10 of 10
Step 13
MAXIMUM WEIGHT CAPACITY
CAUTION: This product is intened to hold the Maximum Weight indicated. Exceeding the
Maximum Weight will result in instability and may cause possible injury.
Step 14
Thank you for purchasing our product! Please retain your receipt to validate warranty
lf you’d like to know more about Officeworks’ furniture products, please visit our website.www.officeworks.com.au
If the drawer’s two side gaps were not aligned,
please pull out the back panel nails and adjust
the cabinet angles to ensure the frame angles
are square. After the drawers are fully aligned
and travel smoothly, fully hammer nails to inside
back panel.