OFW OFW00138 User manual

Width - 70.0cm
Wide 3 Shelf Bookcase
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth -35.0cm
Height - 91.2cm
Rev A - 21/05/2015
011 xx 5509
MADE IN
GREAT BRITAIN
Assembly Instructions -
Please retain for future reference

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.
Assembly should be carried out
by a competent adult only.
Do not use if components are
missing or damaged.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Back panel (90.5 x 69.6cm)
9904
Code -
End (91.2 x 35cm)
x 2 Code - 9899
Shelf (67 x 34.8cm)
9902
x 2 Code -
Top/Bottom (67x34.8cm)
9901
x 2 Code -

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Screw x 8
Code 690001075
AB
E
D
F
Panel pin x 30
Code 760001012
Panel pin guide x 1
Code 684004501
G
Cover Cap x 8
Support Bracket x 1
Code 760001901
H
Screw x 2
Code 690001099
Shelf Support x 8
Code 681003001

Exploded View
4
9904
9899
9901
9901
9902
9899
9902

E
E
E
E
Step 1
Assembly Instructions
5
9901
E
E
E
E
9899
9901
9899
Using screws secure
the top panel and
the bottom panel
to the end panels
Connect top / bottom
panels to end panels.
9901
9901
9899
E
E
x8
IMPORTANT :
Now turn unit onto its front so
finished edges are to the floor
Finished edges

Assembly Instructions
6
Step 2
9901
9901
9899
9899
Squaring up the unit.
IMPORTANT!
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
Ensure a tape
measure is used
to square unit up.
DIAG 3
DIAG 1
XX
XX
YY
YY
XX
XX
YY
YY
DIAG 2
XX
XX
XX
YY
YY
YY
YY
XX
D
x30
F
x1
Step 3
Attach backpanel to
bottom
Secure backpanel
to bottom, end panels and
the top using the panel pins
provided.
Use the panel pin guide
when locating the
panel pins. This will hold the
panel pins vertically and
ensure the correct distance
from the edge.
D
F
9899
9901
9904
IMPORTANT!
The back panel is taped
and folded. Be sure to
take care when unfolding.
9904
TAPED SIDE
Finished edges to the floor
Finished edges to the floor
9901
9899

Assembly Instructions
7
Step 4
Step 5
Attach cover caps
to exposed fittings.
A
x8
Cover any exposed
fittings using the covers
.
A
A
9901 9899
9899
9899
A
A
A
Holes for
shelf studs
Turn unit upright to
attach shelf studs.
A number of holes are
drilled in each end panel
so that the shelves are
adjustable.
Once you have decided
upon the location of the
shelves, insert the shelf
studs as shown.
PUSH!
Once inserted, seat the
shelves on top of the shelf
studs.
G
x8

Assembly Instructions
8
Step 6
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
Warning:
2 people to lift.
Lift with care.
With help move the
unit into position.
Warning:
H
x1
B
x2

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)