OHAir Pyure MySpace Quick start guide

OH Air® and MySpace™ are trademarks or registered trademarks of The Pyure Company Inc., Boynton Beach, Florida, USA.
Pyure MySpace™
Air and Surface Protection
Inspired by Nature.
Trusted to Clean.

Table of Contents
Operational Instructions...................................................................................................... 1
Getting Started ...................................................................................................................... 2
Navigating the Menus .......................................................................................................... 2
Navigating the WiFi Menus.................................................................................................. 4
Internal Cooling Fan.............................................................................................................. 7
Caring for your MySpace™ ................................................................................................... 8
Removing Cover for Cleaning Air Filter and Replacing HGU™ ...................................... 8
HGU™ Cleaning and Replacement...................................................................................... 9
Safe Handling and Disposing of Mercury ......................................................................... 11
Limited Use End-User License Agreement........................................................................ 13
Warranty Information........................................................................................................... 15
Frequently Asked Questions (FAQs)................................................................................... 16
NOTE: HGU™is an acronym for Hydroxyl Generator Unit and it is referred to as either
Optic Assembly or HGU™in this user manual.
What’s in the Box?
1 x MySpace™ Device 1 x User Manual 1 x Power Cord

Safety Warning - Please read and save this manual
• Skin or eye damage may result from directly seeing the light/UV source in this apparatus.
• DO NOT look at the light directly.
• DO NOT expose skin to the light.
• Device must be turned o before unplugging from the mains.
• Disconnect/unplug power before removing the cover, replacing HGU™ or servicing.
• The device is not intended to be used in wet/pooling environments.
• The device is not to be used by children, nor should children be permitted to play with the device.
• The device is not to be used by people with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given instructions or are
beingsupervised.
• AC or DC power input must only be supplied a voltage corresponding
to the markings on the device.
• If the device is obviously damaged, it must not be operated.
• Keep objects away from moving parts.
• Keep liquids away from the appliance and DO NOT wash.
• DO NOT expose UV sensitive materials to the light.
• Always replace the UV source with part HGU™
manufactured by The PYURE Company
Operational Instructions
Your OH Air® MySpace™ is ideal for small to medium spaces such as work areas and
conference rooms, waiting rooms, classrooms, homes, and similar spaces.
This device is not recommended for use in enclosed spaces with no air exchange.
In the event the device is operated in a closed, non-ventilated space, the minimum
volume should be 65 m(2,340 ft). This represents an area of 24 mor 260 ft, assuming
a ceiling height of 2.7 meters (9 feet).
In a well-ventilated space (3 air exchanges per hour) with 2.7 meter (9 foot) ceilings, the
minimum size room in which to operate the device is 9 m(100 ft), and the device
can treat a space as large as 46 m(500 ft). Note: the eective treatment area will vary
depending on the ventilation rate and the ceiling height. For example, the maximum
space will be less than 46 m(500 ft) if the air exchange is greater than 3 times per hour,
or if the ceiling is higher than 2.7 meters (9 feet).
When operating the device in a well ventilated space, the device should be placed at
least 2 meters (6 feet) from anyone who is stationary for an extended period (example
sleeping). If the device is operated in an enclosed space with no ventilation, the device
should be placed at least 4 meters (12 feet) from anyone who is stationary for an
extended period.
The hydroxyls generated by the OH Air® MySpace™ will reduce bacteria, viruses, mold,
pollutants and odors from the air. Surfaces will also be treated, reducing virus, mold
and bacteria. Your MySpace™ is designed to reduce pathogens and improve air quality.
Page 1

Getting Started
When your MySpace™ unit is powered on for the rst time, it will let you select your
preferred language, use the up and down buttons to select from the list and press the
center button to select (an asterisk ‘*’ will be displayed next to the selected option). After
the language has been selected, the unit will default to the Power/Fan Speed Screen
and remember if it was running when last powered.
Page 2
Once selected, press the right button to move to the Power/Fan Speed Main Screen.
Your MySpace™ is designed to conserve energy and provide you with a distraction-free
experience, therefore the menu screen of your MySpace™ will go into standby mode
after thirty seconds of inactivity. In order to wake the menu screen, tap any of the
buttons once.
Timer: Press up to set the time for the unit to run in thirty min intervals up to four hours.
Down will turn the timer and unit o, the center button will stop and start the unit with
no timer.
Navigating the Menus
Active buttons will be lit in blue. The center button will show green if the function on
the current menu item is on (Hydroxyl Generator, WiFi AP, WiFi function) and red if o.
The buttons will ash green if they detect a nger press.
Move between menus: Left and Right Arrows
Scroll through menu: Up and Down Arrow
Turn on/O/Select: Center Button
MAIN
SCREEN
Indicates unit is on Indicates unit is o

Page 3
OH Control: Allows the strength of the Hydroxyls to be adjusted. The level of hydroxyl
output is a function of room size. Follow the guidelines in the table below:
Hydroxyl Output Level Guidelines
Area of Treated Space* Power level
(bars showing on OH display)
Over 9 mor 100 ftPower level 1 (1 bar)
Over 14 mor 150 ftPower level 2 (2 bars)
Over 19 mor 200 ftPower level 3 (3 bars)
Over 23 mor 250 ftPower level 4 (4 bars)
Over 28 mor 300 ftPower level 5 (5 bars)
Over 33 mor 350 ftPower level 6 (6 bars)
Over 37 mor 400 ftPower level 7 (7 bars)
* assuming 2.7 meter (9 foot) ceilings and 3 air changes per hour

Station Details: This shows the WiFi connection information. If the center button is
pressed on this menu, the WiFi function will be turned on/o.
Access Point: This is the WiFi information used to connect and/or congure the unit.
Ifthe center button is pressed on this menu, the WiFi Access Point will be turned
on/o. To access the device connect to SSID displayed. Default is OH Air and password
(admin007) or as displayed on this menu.
Navigating the WiFi Menus
The WiFi interface of the device allows for the control of the device either directly
attached or through your local network, Internet control (to be provided through
armware update), Operational information of the unit, rmware updates and some
debugging support.
Page 4
Live Data: This displays operational information about the unit and is for general
information/support.

WiFi Association shows the current conguration/connection, allows you to select from
an available SSID (WiFi router) and set the password to connect and optionally select a
specic IP for your network (normally leave it as DHCP).
WiFi Access Point Conguration shows the current setup detail and allows you to change
the name of the device on your network (SSID) and password. This unit only connects
to 2.4GHz WiFi networks.
Page 5

MQTT is a network protocol that allows for the secure remote control of the device
across the internet.
Debug Log shows WiFi debugging information for support to assist you if there are
connection issues.
Page 6

Upgrade Firmware allows you to update the software in the unit to the latest version.
These will be made available from time to time.
Internal Cooling Fan
The internal cooling fan is automatically controlled by the temperature of the drive
circuit. It may come on and o during operation of the device and can continue to run
for a couple of minutes after the main unit has been turned o.
Page 7

Caring for your MySpace™
CAUTION: Unplug the device from the mains before performing any cleaning activities.
DO NOT allow any excess water to enter the device or to come into contact with the
internal components. DO NOT use commercial surface cleaners.
The exterior surface of your MySpace™ can be cleaned with a soft cloth dampened with
a diluted solution of dishwashing detergent and water.
Removing Cover for Cleaning Air Filter and Replacing HGU™
CAUTION: Unplug the device from the outlet before removing cover.
Page 8
It is recommended to remove and wash the air lter monthly,
more regularly if it’s being used in a dusty area, by removing
the cover as below, extracting the air lter and rinsing under
the tap to remove large contaminants. Once cleaned, itneeds
to be thoroughly air-dried before re-insertion.
It is recommended to clean the internal chamber and the
optic assembly (HGU™) quarterly, more regularly if it’s
being used in a dusty area, to maintain its peak eciency to
eliminate odors, bacteria, viruses and other volatile organic
compounds (VOCs) in the air and on surfaces. If the HGU™
is in continuous operation, it is recommended to replace
the HGU™ annually with a new HGU™ purchasable via the
website. Every year when the HGU™ needs replacement,
itwill display “tube error” on the main screen.
Step 1 - Place the device on its back with power cord removed
Step 2 - Remove one screw with PH2 Phillips screwdriver
Step 3 - Push both tabs in together to release cover
Step 4 - Lift cover upwards and toward you to remove the cover
Step 5 - Re-assemble cover in reverse order
2
1
3
2
View MySpace™ Step-by-
Step Maintenance Videos

HGU™ Cleaning and Replacement
Step 1 - Refer to the previous section ‘Removing Cover
for Cleaning and Replacement’ to remove the front cover.
Step 2 - To remove the metal cover plate, remove screws
“A-D” using PH1 Phillips head screwdriver. Lift up the plate
to remove it.
Step 3 - To remove the chamber cover, remove screw “E”
using PH1 Philips screw driver. Lift up the chamber cover
to expose the optic assembly (HGU™).
Step 4 - To remove the HGU™, remove two HGU™mounting
screws “F” and “G”. Grasp the center baffle “H” and
manipulate side to side while rmly pulling it away from
the connector and lifting out.
Step 5 - Gently clean the optic in the new HGI™ with a glass
cleaner andalint-free cloth. Ensure optic is completely dry
beforere-insertion.
Step 6 - While the HGU™ is out, remove dust and clean
with a dry cloth.
A
B
C
D
E
FG
H
I
Page 9

Page 10
HGU™Cleaning and Replacement
Step 7 - Carefully locate water connection “I” into the
black socket, then firmly push and manipulate until
fullyinserted.
Step 8 - Re-t HGU™ screws “F” and ”G” conrming HGU™
is correctly seated.
Step 9 - Replace the chamber cover and insert screw “E”.
Step 10 - Replace metal cover plate and re-t screws in the
following sequence, loosely rst, tighten once all in place:
1. A (press cover down to locate screw correctly)
2. B
3. C
4. D
Step 11 - Replace the air lter and front cover of the device
as per previous instructions.
Note: HGU™ is an acronym for Hydroxyl Generator Unit and it is referred to as either
Optic Assembly or HGU™ in this user manual.
A
B
C
D
E
FG

Pa ge 11
Safe Handling and Disposing of Mercury
Mercury is used in the HGU™ in order to generate the plasma needed to produce UV-C
radiation. This is similar to the use of mercury in many types of commercial, uorescent
light xtures. As long as the glass or quartz outer bulb is intact, mercury is contained
within the xture and poses no health hazard. In the event that an optic breaks, less
than 25 mg of mercury could be released. This is much less than what is present in a
commercial thermometer. Liquid metallic mercury is hazardous due to its potential
to release mercury vapor. In humans, approximately 80% of inhaled mercury vapor
is absorbed via the respiratory tract, where it enters the circulatory system and is
distributed throughout the body. Short term exposure to 25 mg of spilled mercury
does not pose a health hazard, provided that the source of the mercury is removed
promptly. Chronic exposure by inhalation, even at low concentrations in the range
0.7–42 g/m3, can cause eects such as tremors, impaired cognitive skills, and sleep
disturbance in workers. The OHSA limit for occupational exposure of elemental mercury
is 0.1 mg/m3. Mercury is also used in most uorescent light xtures.
In the event that the device optic light does not function, the optics should be checked to
ensure that they are intact. If the optic is cracked, but not broken, it should be replaced.
Cracked optics should be double sealed in plastic bags and disposed of according to
local, approved procedures. In the event that the optic breaks and the mercury is spilled,
clean-up should be done immediately according to the following procedure published
by the Environmental Protection Agency.
• Evacuate the room for at least 15 minutes.
• DO NOT attempt to clean up the spill with a vacuum cleaner, mop or broom.
• Dispose of clothing, fabric etc. that has come in contact with mercury; DO NOT wash.
• Only the individual to clean up the spill should re-occupy the space.
• Close the doors to the area of the spill and turn o the HVAC system; open exterior
windows and direct room air out of the window with fans or use an exhaust fan if
the area is equipped with one that vents directly outdoors.
• Cover shoes with disposable foot covers or wear shoes that will be disposed of.
• Remove jewelry as mercury will amalgamate with metals and ruin them.
• Use a commercial mercury spill clean-up kit to remove the spilled mercury.

Page 12
• Identify items in the spill area that can be cleaned and those that cannot.
Non-porous surfaces (nished wood, plastic or concrete) can be cleaned following
this guidance. Porous surfaces or fabric-covered items (upholstery, carpeting,
stued animals, pillows, backpacks, unnished wood, cork, cardboard) are dicult
to clean because mercury beads may be trapped in these materials. If you decide
you cannot clean these items, place them in plastic trash bags or cover or wrap them
in a double layer of plastic and carefully seal with tape. Place the wrapped items in
a secure place, preferably outdoors and out of the reach of children and pets. You
should consult with a trained professional about how to decontaminate or dispose
of these items safely.
• Wear gloves to carefully pick up the larger pieces of broken glass and what
remains of the broken device and place them on a paper towel. Gently fold the
paper towel around these pieces so you can pick the bundle up and place it in a
zipper-type plastic bag. Use index cards or sti cardboard to push smaller pieces
of glass and mercury beads together into a pile. Shine a ashlight at an angle to
locate beads of mercury. The beads will reect light from the ashlight. Check for
mercury in cracks or in hard-to-reach areas where beads may be hidden or trapped.
Check a wide area beyond the spill.
• Use the eyedropper to collect mercury beads and place them in the plasticbag.
Hold the eyedropper at an angle to draw the mercury into the tip. Keep the
eyedropper at an angle to stop the mercury from rolling back out until you can put
the mercury into the plastic bag. Wrap tape (sticky side out) around your gloved
ngers and carefully use it to pick up any remaining glass or beads. Check again
with the ashlight to be sure that no beads of mercury remain.
• At this point, mercury beads may still be trapped in cracks or crevices on irregular
surfaces. Sprinkle sulfur powder over the contaminated area and rub it gently all
over the surface and into the cracks with a paper towel. Sulfur powder binds with
mercury. Use a paper towel dampened with water followed by wiping with another
damp paper towel to clean up the sulfur and mercury. Place the used paper towels
in a zipper-type plastic bag.
• Put all the items that were used to pick up the mercury, including index cards or
cardboard, eyedropper, contaminated tape, paper towels, and zipper-type bags
into the trash bag. Carefully remove rubber gloves by grabbing them at the wrist
and pulling them inside out as they come o. Place the used gloves in the trashbag.
• Carefully seal the trash bag that contains the mercury-contaminated waste and
put it in a secure place, preferably outdoors and out of reach of children and pets
until it can be disposed of safely.
• If possible, open a window and use a fan to ventilate the area to the outdoors for
24-48 hours before resuming normal use. If possible, heat the area (for example,
with a space heater) while still ventilating to the outdoors. Avoid blowing the
exhaust back indoors or into other nearby residences.

Page 13
• Clothes or shoes that did not come in direct contact with liquid mercury should
be removed and put into the trash bag that was left outside the contaminated area
at the beginning of the cleanup. Close the trash bag and take it outdoors. Carefully
remove the shoes and or clothing from the trash bag and air them out thoroughly
outdoors for 24 to 48 hours. After the outdoor airing, items that are washable can
then be laundered.
• Dispose of contaminated items properly! Mercury-contaminated items should not
be placed in the regular household trash. Contact your town or county ocials for
information about hazardous waste disposal in your community.
Limited Use End-User License Agreement
This End-User License Agreement (EULA) is a legal agreement between you (either an
individual or a single entity) and the mentioned owner (The PYURE Company) of any
computer software which may include associated rmware, media, printed materials,
and “online” or electronic documentation (“Licensed PYURE Software”).
By installing, copying, or otherwise using the Licensed PYURE Software, you agree to
be bounded by the terms of this EULA. If you do not agree to the terms of this EULA, do
not install or use the Licensed PYURE Software in the OH Air® product.
Licensed PYURE Software.
The Licensed PYURE Software is protected by U.S. and international copyright, patent,
trade secret laws and well as other international intellectual property laws and treaties.
Upon your acceptance of this EULA, The PYURE Company grants to you a nonexclusive,
revocable license to use the Licensed PYURE Software, provided that you agree to
thefollowing:
1. Grant of License.
The Licensed PYURE Software is licensed, not sold. You own a copy of any media or
hardware on which the Licensed PYURE Software is shipped, but not a copy of the
Licensed PYURE Software itself. The PYURE Company retains all title, copyrights, and
other intellectual property rights in the Licensed PYURE Software and any copies thereof.
You may use a copy of the Licensed PYURE Software with any OH Air® product for which
you have accepted the terms of this EULA.
2. Restrictions.
You must maintain all notices including copyrights on all copies of the Licensed
PYURE Software. You may not modify, adapt, translate, reverse engineer, decompile,
disassemble, or otherwise attempt to learn the source code of the Licensed PYURE
Software, except and only to the extent that such activity is expressly permitted by
applicable law notwithstanding this limitation.

Page 14
3. Termination.
Your rights under this EULA terminate upon your termination of this EULA, or without
prejudice to any other rights, The PYURE Company may terminate this EULA if you fail
to comply with its terms and conditions. In such event, you must destroy all copies of
the Licensed PYURE Software.
4. No Software Warranty Independent from Other Warranties.
The Licensed PYURE Software is being delivered to you “AS IS” and The PYURE Company
makes no warranty as to its use or performance, other than any the “Limited Warranty”
on the OH Air® product described above.
5. LIMITATION OF LIABILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE
PYURE COMPANY OR ITS SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT,
OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION,
LOSS OF BUSINESS INFORMATION, LOSS OF SAVINGS, OR ANY OTHER PECUNIARY LOSS)
ARISING OUT OF THE USE OF OR INABILITY TO USE THE LICENSED PYURE SOFTWARE
PRODUCT, OR FOR PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES, EVEN
IF THE PYURE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
THE ENTIRE LIABILITY OF THE PYURE COMPANY AND YOUR EXCLUSIVE REMEDY UNDER
THIS EULA IS, AT THE OPTION OF THE PYURE COMPANY, CORRECTING OR WORKING
AROUND ERRORS, REPLACING THE MEDIA, OR REFUNDING THE PURCHASE PRICE. IN NO
EVENT SHALL THE PYURE COMPANY’S ENTIRE LIABILITY UNDER THIS EULA EXCEED THE
PURCHASE PRICE (EVEN IF THE LICENSED PYURE SOFTWARE PRODUCT IS DOWNLOADED
WITH OTHER THIRD PARTY SOFTWARE FREE OF CHARGE) OF THE LICENSED PYURE
SOFTWARE PRODUCT.
6. Miscellaneous.
This EULA is governed by the laws of the State of Florida, U.S.A., and jurisdiction
for anyaction based on the Licensed PYURE Software shall lie in a court located in
PalmBeach County Florida. If any part of this EULA is found void and unenforceable,
it will notaect the validity of the balance of the EULA, which shall remain valid and
enforceable according to its terms. Should you have any questions concerning this
EULA, or if you desire to contact The Pyure Company for any reason, please visit:
www.pyure.com/contact.

WARRANTY
Please visit Pyure.com/warranty-registration to register your MySpace™, activate your
warranty and order replacement parts.
The Pyure Company (“Pyure”) warrants that the product set forth below will be free from defects in materials
and workmanship for the period of one (1) years from the date of original purchase under the following
terms and conditions:
To obtain service under this warranty, send or deliver this product within the warranty period together
with the warranty certicate to any Pyure regional oce or Pyure authorized warranty service center. If
requested, by Pyure or a Pyure authorized service center, you must present proof of purchase showing date
and place of purchase. If upon inspection by Pyure or a Pyure authorized warranty service center, the product
is proved to be defective, it will be repaired without charge using, if necessary, new parts or comparable
used parts that have been fully reconditioned and returned to you. The warranty period for replacement
parts shall extend for a period of six (6) months following the installation of same or for the remaining period
of this warranty whichever is longer. This warranty card does not apply in the following cases: (a) damage
to product due to mishandling, alteration, failure to follow operation, maintenance or environmental
instructions prescribed by applicable instruction manual or shipping damage; (b) damage caused during
service performed other than Pyure or a Pyure authorized service center; (c) if the product has had its serial
number(s) or other identifying data removed: or (d) damage, defect or unsatisfactory performance caused
by the use of equipment not manufacturered or distributed by Pyure. IN NO EVENT WILL Pyure BE LIABLE
FOR ANY DAMAGE, INCLUDING INCONVENIENCE, LOST PROFITS, OR LOST SAVINGS, OTHER INCIDENTAL
DAMAGE STEMMING FROM THE USE OF THE PRODUCT OR OUT OF DEFECTS THEREIN, OR BY BREACH OF THIS
EXPRESSED WARRANTY OR ANY IMPLIED WARRANTY WITH THE RESPECT OF THIS PRODUCT, WHETHER ON
ACCOUNT OF NEGLIGENCE OR OTHERWISE, EVEN IF Pyure OR A Pyure AUTHORIZED WARRANTY SERVICE
CENTER HAS BEEN ADVISED OF THE POSSIBLITY OF SUCH DAMAGES.
Some states or provinces do not allow limitations on how long an implied warranty lasts or limitations of
incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you
specic legal rights and you may also have other rights which vary from state to state or province to province.
Page 15

Frequently Asked Questions (FAQs)
What are hydroxyls?
Hydroxyls (HO•) are naturally occurring radicals. They are created in our atmosphere when the
sun’s ultraviolet rays react with water vapor in the air. Hydroxyls are an important agent that
scrub and cleanse our planet’s environment. OH Air® Hydroxyl Generators replicate this naturally
occurring process and bring it indoors.
How do hydroxyls clean surfaces and hard to reach places?
Once the hydroxyls are created, they are sent to ‘seek and destroy’ odor molecules, bacteria,
viruses, mold, VOCs and other chemicals.
This system does not require all of the contaminants within a room to pass through the processing
chamber. Outside the unit the hydroxyls immediately begin a cascade reaction in the air, thus
creating even more hydroxyls. The cascade of hydroxyls quickly disperse throughout the air
and penetrates surfaces and objects and reach places that otherwise can’t be reached. Other
technologies only clean or lter the air that passes through the unit (a small percentage of the
air in a room).
How does it kill mold?
As well as directly destroying spores, the OH Air® system treats infected areas by cutting o the
food source for mold. As a result, there is nothing for mold to feed on since the very bacteria
and micro-organisms that it relies on to survive have been killed o. Only this way can mold be
rendered inert.
Are hydroxyl generators safe to run in occupied areas?
Hydroxyls generators developed by OH Air® are safe to run (and have been independently tested)
in occupied areas. Unlike ozone and harsh chemicals, hydroxyls are completely safe for people,
pets and plants. They will not damage rubber, plastic, leather, vinyl, electronics or other sensitive
materials. They will also not bleach or discolor items - wet or dry.
How long does it take to work?
Hydroxyls are very fast acting and do their work through a chemical reaction. There needs to be
a high enough concentration - If there is no noticeable reduction in odor, a second or stronger
unit may be required. Results are often noticed within the rst few minutes of operation, with
heavy odors being permanently eliminated after 3 – 4 days.
Do hydroxyls smell?
Hydroxyls themselves don’t have any smell. When hydroxyls interact with the environment, that
may create some odor. If the odor is too strong, turn the fan speed on your MySpace™ to lower
settings. The odor may be stronger initially as a room is rst treated.
The odor/mold I was treating is gone, will it come back?
Air and surfaces will be fully treated. If the cause (urine, feces, smoke, cleaning agents, mold,
etc) is within/embedded in the material, the unit will need to run until the source is exhausted or
removed. You can also dampen (wet) down the surface and re-treat to improve results.
Page 16

The Pyure Company
2055 High Ridge Road, Boynton Beach, FL 33426
United States of America
Website: www.pyure.com
Phone: [phone]
email: s[email protected]