OHAUS SCOUT User manual

ScoutTM
USB Host Interface
INSTRUCTION MANUAL
Interfaz Host USB
MANUAL DE INSTRUCCIONES
Interface hôte USB
MODE D’EMPLOI
USB Host-Schnittstelle
BEDIENUNGSANLEITUNG
Interfaccia Host USB
MANUALE D’ISTRUZIONI
USB 主设备组件
使用说明书
USB 호스트 인터페이스
사용 설명서
Интерфейс USB-хост
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
Visit www.scaleman.com to purchase Ohaus Scout Scales
Visit www.balances.com for balances, scales & calibration weights

USB Host Interface EN-1
INTRODUCTION
This Interface Kit is for use with Ohaus Scout STX, SPX, SKX and SJX series
products. The USB Host Interface will help you to export or import the menu
settings and application mode setting parameters. You can also save the weighing
results to the USB flash drive.
INTERFACE INSTALLATION
Install the Interface module on the mini DIN port (round connector) located at the
rear side of the balance as shown. During this process, please make sure the
balance is powered off.
Notes:
Please make sure the small triangle mark (▲) on the round connector is at
the bottom and then plug in.
The appearance of your model may be different.
SETUP & OPERATION
Upon installation of the interface, the balance will recognize the USB Host Interface
and add relevant items to the menu. The USB flash drive must be installed into the
USB Host interface before using the Export/Import operations. See following tables.
For SPX, SKX and SJX Balances:
Upon installation, the balance will show [U.S.B.H.S.t] during the power sequence.
PRINT
Reset: no, yes
Stable: off, on
A.Print: off
On.stable (->Load, Load.Zero)
interval (-> 1….3600)
accept
continuous
Content: Result (-> off, on)
Gross (-> off, on)
Net (-> off, on)
Tare (-> off, on)
Header (-> off, on)
Footer (-> off, on)
Mode (-> off, on)
Unit (-> off, on)
Info (-> off, on)
Layout: Format (->Single, Multi)
Feed (->Line, 4 Lines, Form)
End Print: Exit menu
USB.HST (USB Host)
E.Menu: no, yes
E.APP: no, yes
I.Menu: no, yes
I.APP: no, yes
End USB: Exit menu
Note: Items with bold font are default settings.
Mini DIN port
(Round connector)
Visit www.scaleman.com to purchase Ohaus Scout Scales
Visit www.balances.com for balances, scales & calibration weights

EN-2 USB Host Interface
SETUP DEFINITIONS
Menu Settings
Explanation
PRINT / A. Print –Off
Only sends data when PRINT is pressed.
PRINT / A.Print / On.Stable –Load,
Load.Zero
Balance only transmits stable data.
Load: Print stable value excluding zero
Load.Zero: Print stable value including zero
PRINT / A.Print / interval - (xx) sec
Balance sends data every (xx) seconds.
PRINT / Auto Print –accept
Balance only sends stable accept data in Check
mode.
PRINT / A.Print –Continuous
Balance repeatedly sends data as fast as
possible.
PRINT / Content
On: print relevant content after weighing data
Gross –on: G; Net –on: N; Tare –on: T;
Info –on: balance will print application mode
setting parameters
PRINT / Layout / Format - (Single,
Multi)
Single: print all data in one line
Multi: print all data in multiple lines
PRINT / Layout / Feed - (Line, 4
Lines, Form)
Line: feed one line after printing
4 Lines: feed four lines after printing
Form: feed one page after printing (move to the
top of next page after printing)
USB.HST / E.Menu
Exports menu settings to USB flash drive, saved
file name: "SCT_MENU.txt".
USB.HST / E.App
Exports application mode settings to USB flash
drive, saved file name: "SCT_APP.txt".
USB.HST / I.Menu
Imports menu settings from USB flash drive
USB.HST / I.App
Imports application mode settings from USB
flash drive
Notes:
The exported data will be saved in one file accumulatively.
The weight value will be saved to USB flash drive when pressing the Print button.
The saved file name will be"SCT_DATA.txt". The format is following the PRINT
menu setting. Each saving will be started with "--------------" on the top line.
For STX Balances:
Upon installation, the STX balance will show USB icon ( ) in the upper right
corner.
Menu added
Function
Communication
|--USB Host
|--Save to USB
|--Print Settings
The value can be On or Off
On: “Save to USB”button is active.
Off: “Save to USB”button is inactive.
For more info, please refer to the STX instruction manual.
Visit www.scaleman.com to purchase Ohaus Scout Scales
Visit www.balances.com for balances, scales & calibration weights

USB Host Interface EN-3
Note: Once the USB Host Interface is installed and with a USB flash drive plugged in, the
"Save to USB" button will be active. Pressing "Save to USB" button will save the
weighing result data into the USB flash drive. And the saved file name will
be"STX_DATA.txt".
Data Maintenance
|--Export to USB
|--App.Mode Setting
|--Menu Settings
|--Import to USB
|--App.Mode Setting
|--Menu Settings
Export application mode settings to USB disk. The saved
file name: "STX_APP.txt".
Export menu settings to USB disk. The saved file name:
"STX_MENU.txt".
Import application mode settings from USB disk.
Import menu settings from USB disk.
COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Please note that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Visit www.scaleman.com to purchase Ohaus Scout Scales
Visit www.balances.com for balances, scales & calibration weights

EN-4 USB Host Interface
DISPOSAL
In conformance with the European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE) this device may not be
disposed of in domestic waste. This also applies to countries outside
the EU, per their specific requirements.
Please dispose of this product in accordance with local regulations at
the collecting point specified for electrical and electronic equipment. If
you have any questions, please contact the responsible authority or
the distributor from which you purchased this device.
Should this device be passed on to other parties (for private or
professional use), the content of this regulation must also be related.
For disposal instructions in Europe, refer to www.ohaus.com/weee.
Thank you for your contribution to environmental protection.
Visit www.scaleman.com to purchase Ohaus Scout Scales
Visit www.balances.com for balances, scales & calibration weights