OJ Electronics OCD6-1999 User manual

OCD6-1999
OCD6-1999
INSTRUCTIONS
67472A 04/16 (HKT)
© 2016 OJ Electronics A/S
GREEN COMFORT
Maximum comfort with low energy consumption
• English
• Русский
• Українська

© 2016 OJ Electronics A/S
2
© 2016 OJ Electronics A/S
Fig. 1
Fig. 2
ILLUSTRATIONS
Pages.................................................................................... 3
INSTRUCTIONS
English.................................................................................. 7
Русский.............................................................................. 12
Українська ....................................................................... 17

3
© 2016 OJ Electronics A/S
OCD6-1999
© 2016 OJ Electronics A/S
BR1024A02
© 2015 OJ Electronics A/S
Fig. 1
Fig. 2
BR1024A01
© 2015 OJ Electronics A/S
BR1024A01BR1024A02
ILLUSTRATIONS
Pages.................................................................................... 3
INSTRUCTIONS
English.................................................................................. 7
Русский.............................................................................. 12
Українська ....................................................................... 17

4
© 2016 OJ Electronics A/S © 2016 OJ Electronics A/S
BR1024A04
OCD6-1999
BR1024A03
© 2015 OJ Electronics A/S
BR1024A04
© 2015 OJ Electronics A/S
3
2
1
3
4
BR1024A03
Fig. 3
Fig. 4

© 2016 OJ Electronics A/S
5
© 2016 OJ Electronics A/S
OCD6-1999
OCD6-1999
BR1024A06
© 2015 OJ Electronics A/S
654321
N
L
Fig. 5
BR1024A06
BR1024A07
© 2015 OJ Electronics A/S
BR1024A07
Fig. 6

© 2016 OJ Electronics A/S
6© 2016 OJ Electronics A/S
OCD6-1999
BR1017A08
BR1024A08
© 2015 OJ Electronics A/S
Fig. 7
BR1017A17a
Fig. 9
Udarbejdet af: Udarbejdet d.: 29.05.2015 Side 1af 1
© 2015 OJ ELECTRONICS A/S •STENAGER 13B •DK-6400 SØNDERBORG
NTC 12kΩ@ 25°Celsius
°Celsius
°Fahrenheit
Ohm (Ω)
-10°C14°F55076Ω
0°C32°F34603Ω
10°C50°F22284Ω
20°C68°F14675Ω
30°C86°F9860Ω
BR1024A09
Fig. 8
BR1024A09
© 2015 OJ Electronics A/S
12
21.5º
Manual
Other Mode
I ON
O OFF
FIG. 1 - CONTENT
• Thermostat
• Sensor
The thermostat is an electronic PWM/PI thermostat for temperature
control by means of an NTC sensor located either externally or
internally within the thermostat.
The thermostat is for flush mounting in a wall socket.
This thermostat can be used as a controller for electric room heating
pursuant to EN50559.
Product programme
OCD6-1999 Clock-thermostat with two sensors:
floor sensor and built-in room sensor.
FIG. 2 - WARNING – Important Safety Instructions
Disconnect the power supply before carrying out any installation or
maintenance work on this thermostat and associated components.
The thermostat and associated components should only be installed
by a competent person (i.e. a qualified electrician). Electrical instal-
lation must be in accordance with appropriate statutory regulations.
FIG. 3 - THERMOSTAT PLACEMENT
Mounting of sensor
The floor sensor contains a safety extra-low voltage (SELV) circuit,
allowing it to be placed as close to the floor surface as possible
without having to take account of the risk of shock should the sen-
sor cable become damaged. The two wires connecting the sensor
to the mounting box must be additionally insulated, e.g. shrink flex.
To prevent loose wires in the fixed installation from coming into
contact with the terminal block for the floor sensor, they must be
restrained using cable ties.
It is strongly recommended that the cable and sensor are placed in
a non-conductive installation pipe embedded in the floor. The end of

7
© 2016 OJ Electronics A/S
OCD6-1999
© 2016 OJ Electronics A/S
OCD6-1999
FIG. 1 - CONTENT
• Thermostat
• Sensor
The thermostat is an electronic PWM/PI thermostat for temperature
control by means of an NTC sensor located either externally or
internally within the thermostat.
The thermostat is for flush mounting in a wall socket.
This thermostat can be used as a controller for electric room heating
pursuant to EN50559.
Product programme
OCD6-1999 Clock-thermostat with two sensors:
floor sensor and built-in room sensor.
FIG. 2 - WARNING – Important Safety Instructions
Disconnect the power supply before carrying out any installation or
maintenance work on this thermostat and associated components.
The thermostat and associated components should only be installed
by a competent person (i.e. a qualified electrician). Electrical instal-
lation must be in accordance with appropriate statutory regulations.
FIG. 3 - THERMOSTAT PLACEMENT
Mounting of sensor
The floor sensor contains a safety extra-low voltage (SELV) circuit,
allowing it to be placed as close to the floor surface as possible
without having to take account of the risk of shock should the sen-
sor cable become damaged. The two wires connecting the sensor
to the mounting box must be additionally insulated, e.g. shrink flex.
To prevent loose wires in the fixed installation from coming into
contact with the terminal block for the floor sensor, they must be
restrained using cable ties.
It is strongly recommended that the cable and sensor are placed in
a non-conductive installation pipe embedded in the floor. The end of
Instruction
English

8
© 2016 OJ Electronics A/S © 2016 OJ Electronics A/S
the pipe must be sealed and the pipe placed as high as possible in
the concrete layer. Alternatively, the sensor can be embedded di-
rectly in the floor. The sensor cable must be led through a separate
conduit or segregated from power cables.
The floor sensor must be centred between loops of heating cable.
The sensor cable may be extended up to 30m by means of a
separate two-core cable. Two vacant wires in a multi-core cable
used, for example, to supply current to the floor heating cable must
not be used. The switching peaks of such current supply lines may
create interference signals that prevent optimum thermostat func-
tion. If a shielded cable is used, the shield must not be connected
to earth (PE). The two-core cable must be placed in a separate
pipe or segregated from power cables in some other way.
Mounting of thermostat with built-in sensor
The room sensor is used for comfort temperature regulation in
rooms. The thermostat should be mounted on the wall approx.
1.5 m above the floor in such a way as to allow free air circulation
around it. Draughts and direct sunlight or other heat sources must
be avoided.
FIG. 4 - OPENING THE THERMOSTAT
1. Slide the power button down to O “0”.
2. Insert a small screwdriver into the central slot of the front cover
to press and hold the catch.
3. Then push the handle of the screwdriver downwards to release
the rear part from the front cover.
4. Carefully pull the rear part away from the front cover, starting
with the lower part of the thermostat.
FIG. 5 - CONNECTIONS
Connect the wires in accordance with the diagram. The wires must
be connected as follows:
Term. 1: Neutral (N)
Term. 2: Live (L)
Term. 3-4: Output, max. 16 A
Term. 5-6: External floor sensor
FIG. 6 + 7 - MOUNTING THE THERMOSTAT
1. Mount the rear part of the thermostat in the wall socket.
OCD6-1999 English
2. Refit the front cover to the rear part of the thermostat.
Carefully press the cover onto the thermostat, starting with the
upper part of the cover before fitting the lower part of the cover.
3. Click the cover into place by applying light, even pressure.
Warning! Do not apply pressure to the corners of the display
cover or to the display itself.
DO NOT open the thermostat by releasing the four fixing clips on
the back.
FIG. 8 - OPERATING THE THERMOSTAT
There is an ON/OFF switch on the left side of the thermostat: up is
ON - down is OFF.
The resistive touchscreen requires a soft tap with your fingertip to
register the touch.
Installer Wizard:
The first time the thermostat is connected, push the power slide
button to On “I” The Installer Wizard on the touchscreen will guide
you through the set up of:
1. Region
2. Language
3. Date
4. Time
5. Floor Type
Programming
See user manual.
http://www.ojelectronics.com/OCD6
FIG. 9 - TROUBLESHOOTING
If the sensor is disconnected or short-circuited, the heating system
is switched o. The sensor can be checked against the resistance
table.
OCD6-1999 English

© 2016 OJ Electronics A/S
9
© 2016 OJ Electronics A/S
the pipe must be sealed and the pipe placed as high as possible in
the concrete layer. Alternatively, the sensor can be embedded di-
rectly in the floor. The sensor cable must be led through a separate
conduit or segregated from power cables.
The floor sensor must be centred between loops of heating cable.
The sensor cable may be extended up to 30m by means of a
separate two-core cable. Two vacant wires in a multi-core cable
used, for example, to supply current to the floor heating cable must
not be used. The switching peaks of such current supply lines may
create interference signals that prevent optimum thermostat func-
tion. If a shielded cable is used, the shield must not be connected
to earth (PE). The two-core cable must be placed in a separate
pipe or segregated from power cables in some other way.
Mounting of thermostat with built-in sensor
The room sensor is used for comfort temperature regulation in
rooms. The thermostat should be mounted on the wall approx.
1.5 m above the floor in such a way as to allow free air circulation
around it. Draughts and direct sunlight or other heat sources must
be avoided.
FIG. 4 - OPENING THE THERMOSTAT
1. Slide the power button down to O “0”.
2. Insert a small screwdriver into the central slot of the front cover
to press and hold the catch.
3. Then push the handle of the screwdriver downwards to release
the rear part from the front cover.
4. Carefully pull the rear part away from the front cover, starting
with the lower part of the thermostat.
FIG. 5 - CONNECTIONS
Connect the wires in accordance with the diagram. The wires must
be connected as follows:
Term. 1: Neutral (N)
Term. 2: Live (L)
Term. 3-4: Output, max. 16 A
Term. 5-6: External floor sensor
FIG. 6 + 7 - MOUNTING THE THERMOSTAT
1. Mount the rear part of the thermostat in the wall socket.
2. Refit the front cover to the rear part of the thermostat.
Carefully press the cover onto the thermostat, starting with the
upper part of the cover before fitting the lower part of the cover.
3. Click the cover into place by applying light, even pressure.
Warning! Do not apply pressure to the corners of the display
cover or to the display itself.
DO NOT open the thermostat by releasing the four fixing clips on
the back.
FIG. 8 - OPERATING THE THERMOSTAT
There is an ON/OFF switch on the left side of the thermostat: up is
ON - down is OFF.
The resistive touchscreen requires a soft tap with your fingertip to
register the touch.
Installer Wizard:
The first time the thermostat is connected, push the power slide
button to On “I” The Installer Wizard on the touchscreen will guide
you through the set up of:
1. Region
2. Language
3. Date
4. Time
5. Floor Type
Programming
See user manual.
http://www.ojelectronics.com/OCD6
FIG. 9 - TROUBLESHOOTING
If the sensor is disconnected or short-circuited, the heating system
is switched o. The sensor can be checked against the resistance
table.
OCD6-1999 English

10
© 2016 OJ Electronics A/S © 2016 OJ Electronics A/S
Error codes
E0: Internal fault. The thermostat must be replaced.
E1: Built-in room sensor fault. Replace the thermostat or continue
to use it with the floor sensor only.
E2: External floor sensor fault. Replace the floor sensor or continue
to use the thermostat with the built-in room sensor only.
E5: Internal overheating. Inspect the installation.
CE marking
According to the following standard:
LVD/EMC: EN 60730-2-9
RoHS: 2011/65/EU
Classification
Protection from electric shock must be assured by appropriate
installation. Appropriate installation must meet the requirements of
Class II (reinforced insulation).
Environment and recycling
Please help us to protect the environment by disposing of the
packaging in accordance with national regulations for waste
processing.
Recycling of obsolete appliances
Appliances with this label must not be disposed of with
general household waste. They must be collected
separately and disposed of in compliance with local
regulations.
OCD6-1999 English
OCD6-1999 English