OJ Electronics MTD3-1999 User manual

© 2019 OJ Electronics A/S
MTD3-1999
User Manual
67772A 06/19 (AML)

PAGE 2
© 2019 OJ Electronics A/S
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
APP: Sensor Application 1/2. . . . . . . . . . . . . . . . . . . . . . . . 6
APP: Sensor Application 2/2. . . . . . . . . . . . . . . . . . . . . . . . 7
SCA: Temperature Scale . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Li: Floor Temperature Limit . . . . . . . . . . . . . . . . . . . . . . . . 9
TP: Temperature Read-out. . . . . . . . . . . . . . . . . . . . . . . . 10
LCD: Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ADJ: Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
NSB: Night Setback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DEF: Frost Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PWM: Pulse Width Modulation 1/2. . . . . . . . . . . . . . . . . . . 15
PWM: Pulse Width Modulation 2/2. . . . . . . . . . . . . . . . . . . 16
PLI: Power Limit 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PLI: Power Limit 2/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TIME: Time and Event Settings 1/2 . . . . . . . . . . . . . . . . . . 19
TIME: Time and Event Settings 2/2 . . . . . . . . . . . . . . . . . . 20
SW: Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Done: Exiting the Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshooting and Additional Information . . . . . . . . . . . . 23
Change of Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . 24

PAGE 3
© 2019 OJ Electronics A/S
Introduction
Thank you for buying our MTD3 thermostat.
We hope you will enjoy the ease of use oered by
the well-known user interface and design.
This high-quality thermostat is designed to have
minimum impact on the environment and will
at the same time provide you with long-lasting
heating comfort.
The thermostat will switch on your heating system
at preset times each day of the week.
The thermostat is preset with up to four events for
each day of the week. Lowering the temperature
when your home is unoccupied will reduce your
energy costs without reducing comfort.
The thermostat comes with preset heating
schedules suitable for most homes.
The MTD3 thermostat has a temperature setting
range of 0-40°C, a night setback, frost protection
and limit temperatures that ensure your comfort
and protect your property from temperature
excesses.
The front cover can be flipped down.
The on/o switch is located behind the front cover, on
the left side of the front, up = on / down = o.
On the right there are three buttons.
A top button, a middle button and a bottom button.
The middle button is used to access the menu and
confirm changes and settings made in the menu.
The top and bottom buttons are used to navigate
through the menu and change parameters and
settings.
To access the menu, activate the thermostat by
pushing any of the three buttons.
Then press down the middle button for five seconds.
Note: If you press down the middle button for ten
seconds, the thermostat will perform a factory reset
and all settings will then be reset to factory settings.
This thermostat can be used as a controller for electric
room heating pursuant to EN50559.

PAGE 4
© 2019 OJ Electronics A/S
Menu Overview
Menu Setting Options
APP (APP) APP: A; F; C; AF; AE
5gA (SCA) SChi: SCLo - 40.0°C
SCLo: 0.0°C - SChi
Li (Li) Lihi: LiLo - 40°C
LiLo: 0°C - Lihi
tP (tP) FLo: Actual measured temperature
ro: Actual measured temperature
Lgd (LCd) SCA: C; nu
diS: SP; tP
AdJ (AdJ) Measured temperature +/- 10°C
n5b (nSb) 2.0°C - 8.0°C
dEF (dEF) 5.0°C - 10.0°C
Pvm (PWM)
oFF; on; AUt
oFF: diF: 0,3–10,0
on: CYC: 15–60
AUt: CYHi: 10–60
AUt: CYLo: 10–30
Menu Setting Options
Pli (Pli) 0-30 min
t1me (Time)
ModE: o; 5:2; 6:1; 7:0; 0:7
dAY: Non; tuE; UEd; thu; Fri; SAt; Sun
hour: 0-23
Min: 0-59
5v (SW) None
DonE (Done) Save settings and exit the menu
(Options available may vary depending on version)

PAGE 5
© 2019 OJ Electronics A/S
Icons
Icon Meaning Icon Meaning
Scheduled operation
Night setback
Frost protection mode
Heating is activated
Child lock is engaged
Fahrenheit is chosen as
temperature scale
Celsius is chosen as
temperature scale
The thermostat is in regulator
mode APP: C

PAGE 6
© 2019 OJ Electronics A/S
This option allows you to choose which sensor is used to
control the heating system. If a factory reset is performed,
the thermostat will auto detect an external sensor.
• A: With this setting, the internal room sensor inside
the thermostat, controls the heating system.
• F: With this setting, the external floor sensor controls
the heating system.
• C: With this setting, the thermostat operates as a
regulator and no sensors are used. The setting is a
percentage of the full load in steps of 1%.
Note that Floor Protection is not active when using
the thermostat as a regulator.
• AF: With this setting, the internal room sensor controls
the heating system subject to maximum and
minimum limits for floor temperature.
The maximum temperature limit protects wooden
floors from excessive heat.
The minimum temperature limit prevents the floor
from becoming uncomfortably cold when heating
is not needed, such as in a bathroom. Note that
this function will increase energy consumption.
Floor limit temperatures are set in the “Li : Floor
Temperature Limit” menu.
APP: Sensor Application 1/2
• Access the menu.
• Scroll through the menu until you come to APP.
• Press the middle button to enter the SENSOR
APPLICATION setting.
• Use the top or bottom button to select the appli-
cation that fits your installation.
• Confirm your choice with the middle button.

PAGE 7
© 2019 OJ Electronics A/S
APP: Sensor Application 2/2
• AE: With this setting, an optional external room sensor
(connected to the floor sensor terminals) controls
the heating system.
(Options available may vary depending on version)
Menu structure:
APP: A; F; C; AF; AE

PAGE 8
© 2019 OJ Electronics A/S
SCA: Temperature Scale
This option allows you to set the minimum and maximum
temperatures to which the thermostat can be set.
Operating temperatures:
• SChi: Maximum temperature scale can be set between
minimum temperature (SCLo) and 40°C.
• SCLo: Minimum temperature scale can be set between
0°C and the maximum temperature (SChi).
(If “Sensor Application” is set to “Floor”, a maximum
temperature of 27°C can protect wooden floors from
drying out. For detailed information, please ask your
flooring supplier).
• Access the menu.
• Scroll through the menu until you come to SCA.
• Press the middle button to enter the scale settings.
• Use the top and bottom buttons to set the limit for the
highest temperature the thermostat may use as its
setpoint temperature.
• Confirm your choice with the middle button.
• Use the top or bottom button to set the limit for the
lowest temperature the thermostat may use as its
setpoint temperature.
• Confirm your choice with the middle button.
Menu structure:
SCA:
SChi: 0,0°C - 40.0°C
SCLo: 0,0°C - SChi
(Options available may vary depending on version)

PAGE 9
© 2019 OJ Electronics A/S
Li: Floor Temperature Limit
This option allows you to set the minimum and maximum
limits for the floor temperature.
Floor temperature limits:
Floor temperature limits allow you to set the highest (Lihi)
and lowest (LiLo) permissible floor temperature during
room temperature control with the sensor application AF.
If the floor temperature rises above the maximum
temperature limit, the thermostat will deactivate the
heating system to maintain the temperature below the set
maximum.
If the floor temperature drops below the minimum
temperature limit, the thermostat will activate the heating
system to maintain the temperature above the set
minimum.
Note that this feature is only applicable in sensor
application AF.
• Access the menu.
• Scroll through the menu until you come to Li.
• Press the middle button to enter the Limit settings.
• Use the top and bottom buttons to set the limit for the
highest temperature the thermostat may reach.
• Confirm your choice with the middle button.
• Use the top and bottom buttons to set the limit for the
lowest temperature the thermostat may reach.
• Confirm your choice with the middle button.
Menu structure:
Li:
Lihi: LiLo - 40°C
LiLo: 0°C - Lihi
(Options available may vary depending on version)

PAGE 10
© 2019 OJ Electronics A/S
TP: Temperature Read-out
Depending on which sensors are connected and which
sensor application is chosen, temperatures from the floor
sensor and the internal room sensor can be monitored
here.
Display settings are not applicable if the sensor
application is set to C.
• Access the menu.
• Scroll through the menu until you come to TP.
• Press the middle button to enter the temperature
read-out.
Either the floor sensor temperature, the room sensor
temperature, or both are shown depending on the
sensor application setting
• Use the middle button to skip to the next sensor
type and skip to the menu.
Menu structure:
TP:
FLo: Actual measured floor temperature
ro: Actual measured room temperature
(Options available may vary depending on version)

PAGE 11
© 2019 OJ Electronics A/S
LCD: Display Settings
This option allows you to select which data you want to
be shown in the idle display.
SCA = Temperature scale setting:
C = Celsius
F = Fahrenheit
(nU = numerical 0-100%)
diS = Displayed in idle display:
SP = Setpoint temperature
tP = Measured temperature
CL = Clock
Display settings are not applicable if the sensor applicati-
on is set to C.
• Access the menu.
• Scroll through the menu until you come to LCD.
• Press the middle button to enter the temperature scale
setting.
• Use the top and bottom buttons to toggle between the
dierent options.
• Confirm your choice with the middle button.
• Use the top and bottom buttons to toggle between the
dierent options.
• Confirm your choice with the middle button.
Menu structure:
LCd
SCA: C; F; nu
diS: SP; tP; CL
(Options available may vary depending on version)

PAGE 12
© 2019 OJ Electronics A/S
ADJ: Adjust
This option allows you to calibrate the measured room
temperature.
You should calibrate the sensor if the temperature reading
diers from the actual temperature.
The measured temperature must be entered.
Note that with sensor application F, the temperature is
measured in the floor, this temperature would be higher
than the ambient temperature.
Adjust is not applicable if the sensor application is set to
C.
You can calibrate the sensor with +/- 10°C in steps of
0.1°C in the following way:
• Access the menu.
• Scroll through the menu until you come to ADJ.
• Press the middle button.
• Use the top and bottom buttons to adjust the sensor
with the value with which you want to increase/de-
crease the temperature.
• Confirm your choice with the middle button.
Menu structure:
AdJ:
Measured temperature +/- 10°C
(Options available may vary depending on version)

PAGE 13
© 2019 OJ Electronics A/S
NSB: Night Setback
This option allows you to set the temperature by which the
temperature should be reduced when NSB is activated.
NSB is activated either by the event schedule or with a
signal from an external timer connected to terminal S.
When the NSB signal is active, a half moon icon is shown in
the display together with the reduced setpoint temperature.
The function is factory set to 5°C but can be set to values
between 2-8° in steps of 0.5°C.
If the application is set to Cand ”Night setback” is
selected, the night setback is set in relative values. The
setpoint specifies (in per cent) the time the unit is to remain
active in a PWM cycle, which is usually 20 minutes, while
the reset degrees figure is specified as a percentage of the
setpoint. The setpoint multiplied by the reset degree gives
the activation degrees figure.
Example: If the setpoint is set to 60% and night setback is
set to 25%, the activation degrees figure will be (0.60 x 0.25
= 0.15) = 15%.
• Access the menu.
• Scroll through the menu until you come to
NSB.
• Press the middle button to enter the night
setback setting.
• Use the top and bottom buttons to adjust
the value by which you want to decrease the
temperature when NSB is activated.
• Confirm your choice with the middle button.
Menu structure:
nSb:
2.0 - 8.0 (Options available may vary depending on version)

PAGE 14
© 2019 OJ Electronics A/S
DEF: Frost Protection
This option allows you to set the parameters for a
possible frost protection function.
An external signal can activate the frost protection
function, the thermostat will then maintain a fixed floor/
room temperature.
The function is factory set to 8°C but can be set to values
between 5-10° in steps of 0.5°C.
If the application is set to Cand ”Frost protection” is
selected, the frost protection is set in absolute values in
per cent.
• Access the menu.
• Scroll through the menu until you come to DEF.
• Press the middle button to enter the frost protection
settings.
• Use the top and bottom buttons to set the temperature
you want to be the setpoint temperature when DEF is
activated.
• Confirm your choice with the middle button.
Menu structure:
dEF: 5.0°C - 10.0°C
(Options available may vary depending on version)

PAGE 15
© 2019 OJ Electronics A/S
PWM: Pulse Width Modulation 1/2
With this setting, you can change the duration of the
heating periods.
O: Simple “on/o” regulation, where the relay is closed
when the measured temperature is below the setpoint
and opened when the measured temperature is above the
setpoint. A hysteresis (diF) is used to avoid too frequent
relay switching.
On: The relay is closed or open depending on the average
temperature measured in a fixed period of time (15 - 60
minutes).
Depending on the temperature deviation, the duty cycle of
the “on time” is increased or decreased, giving longer or
shorter time periods when the heating is active.
• Access the menu.
• Scroll through the menu until you come to PUN.
• Press the middle button to enter the PWM settings.
• Use the top and bottom buttons to toggle between
the dierent pulse width modulation modes.
• Confirm your choice with the middle button.
• Use the top and bottom buttons to set the hysteresis
or duty cycle.
• Confirm your choice with the middle button.

PAGE 16
© 2019 OJ Electronics A/S
PWM: Pulse Width Modulation 2/2
Auto: Similar to “PWM On”, but the PWM period is
increased or decreased depending on the minimum and
maximum temperature measured during a PWM period.
This will increase the lifetime of the relay by reducing the
number of relay switches, and still ensure the comfort
of the user by keeping the temperature swings below an
acceptable level.
Menu structure:
PWM:oFF; on; AUt
oFF: diF: 0,3 - 10,0
on: CYC: 15 - 60
AUt: CYHi: 10 - 60
CYLo: 10 - 30
(Options available may vary depending on version)

PAGE 17
© 2019 OJ Electronics A/S
PLI: Power Limit 1/2
This thermostat complies with EN 50559 (VDE 0705-
559) for electrical floor heating. The regulation applies to
electrical floor heating with a maximum floor weight of
4 kN/m². To ensure that hotspots due to unintentionally
covering up the surface are avoided, the heating function
can be time-limited as per EN/DIN.
Note that this function is not applicable to other heating
applications such as wall and/or ceiling heating if it can
be foreseen in advance that unintentional covering up of
floor area might occur In this case it would be important
to assess the correct period of time for which the floor
heating must be time-limited.
The heating can be limited by a set number of minutes
per hour. The thermostat will then divide the given number
of minutes per hour into 3 periods, depending on the
thermostat’s actual PWM cycle.
Example:
If obstacles could be present that cover up the floor,
then the heating might need to be limited by a number of
minutes so as to avoid hotspots on the floor.
If you want the thermostat to provide heat a maximum of
90% of the time, then the thermostat should be limited by
10%. Ten per cent of one hour is 6 minutes.

PAGE 18
© 2019 OJ Electronics A/S
PLI: Power Limit 2/2
Enter 6 minutes in the PLI menu in order to reduce the
heating by 10%.
Equation to calculate number of minutes that could be
entered in the PLI menu - when an average heating eect
is desired:
Average desired heating eect per m2
Floor heating element output per m2
(
1-
( )
)
∗ 60 min.
Note!
If the result of the equation is negative then nothing
should be entered.
The function is factory set to 0 minutes but can be set to
values between 0-30 minutes in steps of 1 minute.
• Access the menu.
• Scroll through the menu until you come to PLi.
• Press the middle button to enter the pulse limit settings.
• Use the top and bottom buttons to set the number
of minutes with which you want the heating to be
deactivated per hour.
• Confirm your choice with the middle button.
Menu structure:
PLi: 0 - 30
(Options available may vary depending on version)

PAGE 19
© 2019 OJ Electronics A/S
TIME: Time and Event Settings 1/2
The MTD3 has a timer function that keeps track of the
current weekday and time of the day.
It is possible to select dierent event schedules for the
MTD3.
The events dier in the number of days that use 4 events
(with a reset period during both night and daytime) and 2
events (only using a reset period for the night).
The dierent event schedules of the MTD3 has the
following definitions:
OFF: Events are disabled and the comfort temperature is
maintained 24/7
5 : 2: Monday – Friday with 4 events,
Saturday & Sunday with 2 events
6 : 1: Monday – Saturday with 4 events,
Sunday with 2 events
7 : 0: Monday – Sunday with 4 events
0 : 7: Monday – Sunday with 2 events
Note: If an external timer is used, this takes priority.

PAGE 20
© 2019 OJ Electronics A/S
TIME: Time and Event Settings 2/2
Time schedule for the events:
4-event: Time: Temperature:
Morning 06:00-08:00 Setpoint
Daytime 08:00-16:00 Setpoint - NSB
Evening 16:00-23:00 Setpoint
Night 23:00-06:00 Setpoint - NSB
2-event: Time: Temperature:
Day 08:00-23:00 Setpoint
Night 23:00-08:00 Setpoint - NSB
• Access the menu.
• Scroll through the menu until you come to tiNE.
• Press the middle button to enter the time and event
settings.
• Use the top and bottom buttons to toggle between the
dierent schedule modes.
• Confirm your choice with the middle button.
• Use the top and bottom buttons to set the current day.
• Confirm your choice with the middle button.
• Use the top and bottom buttons to set the current hour.
• Confirm your choice with the middle button.
• Use the top and bottom buttons to set the current
minutes.
• Confirm your choice with the middle button.
Menu structure:
tiME:
NodE: oFF; 5:2; 6:1; 7:0; 0:7
dAY: Non; tuE; UEd; thu; Fri; SAt; Sun
hour: 0-23
Nin.: 0-59