Okayo AT-100 User manual

(A) Numeric keypad 0~9:
Act as message code, volume adjustment (7 and 9) and next
message (0).
(B) LED indicator:
Green LED – power on; Amber LED – low battery;
Red LED flashing – running out of power.
Press to power on; press and hold 2 seconds to power off.
Play / Pause:
Play or pause a selected message.
(D) Power ON/OFF; Stop button:
Press to stop playing a soundtrack while it is played.
(E) Headphone jack:
2 headphone jacks (stereo) available.
(F) Hole for battery case removal:
Insert a pin in this hole to unlock battery case,
and then slide it to remove.
(G) Battery case:
(H) IEEE 1394 port:
Act as a port for connection with audio guide data updater.
(I) Lanyard tie-up:
To be used with lanyard as a hand-free solution.
(J) Loudspeaker:
Direct sound output when proceeds it with private listening.
It will not work when headphone is in use.
Open battery case with a pin (ψ1.0mm) and allocate batteries.
(C)
(E) (E)
(F)
(G)
(I)
(H)
(J)
(A)
(B)
(C)
(D)
Addendum If your handset has this graphic under the '0' key then this addendum applies
End of Addendum

(A)Earphone jack:
Earphone jack (stereo) x 2.
(B)Loudspeaker:
An alternative for individual preference in listening.
Loudspeaker will not work when an earphone is used.
(C)Numeric keypad 0~9:
Act as message code, volume adjustment and pause.
(D)Play/Stop:
To play or stop a selected message.
(E)Power on/power off:
Press the button to power on; press and hold 2 seconds to
power off.
(F)LED indicator:
Greed LED-power on (stand-by); Amber LED-power
insufficient ; Red LED glittering-running out of power.
(G)Hole on rear casing:
Unlock battery door by inserting a pin in the hole on rear casing.
(H)Battery door:
Insert a pin (ψ1.0 mm) in the hole on rear casing and slide it to
change batteries.
(I)Lanyard loop:
Used with lanyard N-30 as a solution for hand-free.
(J)IEEE 1394 port:
Act as a port to connect with Audio Guide Updater ATC-110U.
(B)
(C)
(D)
(E)
(F)
(A) (A)
(G)
(H)
(I)
(J)

(A)Earphone jack:
Earphone jack (stereo) x 2.
(B)Loudspeaker:
An alternative for individual preference in listening.
Loudspeaker will not work when an earphone is used.
(C)Numeric keypad 0~9:
Act as message code, volume adjustment and pause.
(D)Play/Stop:
To play or stop a selected message.
(E)Power on/power off:
Press the button to power on; press and hold 2 seconds to
power off.
(F)LED indicator:
Greed LED-power on (stand-by); Amber LED-power
insufficient ; Red LED glittering-running out of power.
(G)Hole on rear casing:
Unlock battery door by inserting a pin in the hole on rear casing.
(H)Battery door:
Insert a pin (ψ1.0 mm) in the hole on rear casing and slide it to
change batteries.
(I)Lanyard loop:
Used with lanyard N-30 as a solution for hand-free.
(J)IEEE 1394 port:
Act as a port to connect with Audio Guide Updater ATC-110U.
(B)
(C)
(D)
(E)
(F)
(A) (A)
(G)
(H)
(I)
(J)