Olarm PRO Nemtek User manual
www.olarm.co/start
Nemtek Energizer Installation Guide
E & OE. Terms & conditions may apply. Page 1
2022-02-14
Connect the 4-pin connector to the Universal port on
the Olarm PRO. Cut the 5-pin plug off the cable and
strip the wires so you can insert them. Wire the Olarm
PRO into the keybus according to the diagram below.
The manual focuses on Nemtek
• Druid 13LCD, 15LCD, 18LDC, 25LCD & 28LCD
• Merlin M4i - Coming soon
• Merlin Stealth M18S & M28X - Coming
soon
Disconnect both the mains and battery power from
the electric fence energizer before continuing.
Note: The Druid only supports two keypads
& Olarm PRO counts as Keypad #2. You may
therefore need to forfeit a keypad if you already
have two connected.
The Olarm PRO box includes the following:
• 1x Olarm PRO device
• 1x Connector cable
• 1x Drill hole template and LED colour legend
• 2x Screws and wall plugs
Scan the QR code (left), or navigate to your App store
on your device and search for ‘Olarm’. This Olarm PRO
will require an active subscription to function. Please
more information.
Druid: You will be prompted to enter your Master PIN
and Reset PIN. These are by default 1234 and 5555
respectively. Please contact the Nemtek installer
should these not work.
STEP 3 - Download the Olarm mobile app &
register your device
STEP 4 - Power down the electric fence
energizer
STEP 5 - Connect your Olarm PRO device to
your electric fence energizer
STEP 2 - Unbox your Olarm PRO
Nemtek panel labels
Olarm cable wire colour
Red +
Black -
Green D
STEP 1 - Locate your Nemtek electric fence
energizer
Druid Merlin 4 Merlin Stealth
Merlin: You will be prompted to enter your Master
PIN and User PIN. These are by default 1234 and 5555
respectively. Please contact the Nemtek installer
should these not work.
Druid 13LCD & 15LCD Druid 18LCD Druid 25LCD & 28LCD
Merlin M4i Merlin Stealth M18S & M28X
Coming soon
www.olarm.co/start
Nemtek Energizer Installation Guide
E & OE. Terms & conditions may apply. Page 2
2022-02-14
Mount your device using the screws and drill template
provided. We suggest mounting the Olarm PRO
device on a wall as far from the Nemtek energizer as
convenient.
Troubleshooting
If your device LED remains ashing green
for more than 3 minutes - please check the
connection between the Olarm PRO and the
electric fence energizer.
If your device LED is red - please check the
connection between the Olarm PRO and the
electric fence energizer.
If your device LED is orange - please ensure
that the Olarm PRO is located in an area with
good mobile signal strength. If it is not, please
ensure that your device is connected to WiFi
using the wizard inside the Olarm App.
If your device LED is not coming on - please
check the connection between the Olarm PRO
and the electric fence energizer and that the
electric fence energizer is connected to power.
If your device LED remains purple for more
than 15 minutes - please contact Olarm Support:
STEP 7 - Mount the Olarm PRO
Note:
• Please do NOT mount the Olarm PRO near any
other radio equipment. They may interfere
with each other and result in your device not
functioning correctly.
• The Olarm PRO device is not weather resistant,
and you will need to install it in a suitable non-
metal enclosure if outdoors.
Please follow the in-app guide to connect your Olarm
PRO to WiFi for enhanced connectivity.
STEP 8 - Connect to WiFi
Note: The Olarm PRO only supports 2.4GHz WiFi.
Note:
• Please note that the Olarm PRO acts as a
keypad when installed on a Nemtek energizer
and will automatically cycle through the
zones to read each zone’s status on multi-
zone energisers. Any key press on the keypad
will stop the zone cycling. The Olarm PRO will
commence zone cycling after not detecting a
key press for 30 seconds.
• Olarm PRO with batch number starting with
2022 onward are compatible.
STEP 6 - Turn the Nemtek electric fence
energizer back on
White Booting up
Flashing green Connecting to energizer
Flashing blue Connecting to cloud
Blue Connected, all okay
Red Cannot connect to energizer
Orange Cannot connect to cloud
Yellow WiFi pairing active
Purple Firmware upgrading - do not
power the device off
Check your Olarm PRO’s status.
