Olivetti d-COLOR MF 2400 User manual

Facsimile User’s Guide
d-COLOR MF2400
Code: 569404en

PUBLICATION ISSUED BY:
Olivetti S.p.A.
Gruppo Telecom Italia
Via Jervis, 77 - 10015 Ivrea (ITALY)
www.olivetti.com
Copyright © 2011, Olivetti
The manufacturer reserves the right to carry out modifications to the product described in this manual at any time
and without any notice.
ENERGY STAR is a U.S. registered mark.
The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection
Agency in response to environmental issues and for the purpose of advancing the development and utilization of
more energy efficient office equipment.
Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as
the characteristics of the product:
∀incorrect electrical power supply;
∀incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the
User’s Manual supplied with the product;
∀
replacement of original components or accessories with others of a type not approved by the manufacturer, or
performed by unauthorised personnel.
All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying, recording or by any information storage and retrieval
system, without permission in writing from the Publisher.
The mark affixed to the product certifies that the
product satisfies the basic quality requirements.
Allrightsreserved
x-1

x-2

Contents
Contents x-3
Thank You................................................................................................... x-1
Trademarks ................................................................................................. x-1
Copyright Notice......................................................................................... x-1
Manual Notice............................................................................................. x-1
1 Introduction .................................................................................................... 1-1
Machine Parts ................................................................................................ 1-2
Front View ................................................................................................... 1-2
Rear View .................................................................................................... 1-3
2 Control Panel and Configuration Menu ....................................................... 2-1
About the Control Panel ................................................................................2-2
Fax Mode Screen ...........................................................................................2-5
Main Screen................................................................................................ 2-5
Entering Fax Mode...................................................................................... 2-8
Symbol list .................................................................................................. 2-8
UTILITY Menu ................................................................................................ 2-9
MACHINE SETTING Menu........................................................................ 2-10
ADMIN. MANAGEMENT Menu ................................................................. 2-12
DIAL REGISTER Menu .............................................................................. 2-18

Contentsx-4
FAX TX OPERATION Menu....................................................................... 2-19
FAX RX OPERATION Menu ......................................................................2-22
REPORTING Menu.................................................................................... 2-26
Specifying Settings in UTILITY Menu ........................................................ 2-28
General Procedure for Specifying Settings in UTILITY Menu...................2-28
Memory Reception.................................................................................... 2-28
Setting Up the Memory RX Mode.............................................................2-29
Turning Off the Memory RX Mode ............................................................ 2-30
Specifying Forwarding Settings................................................................ 2-30
3 Sending Faxes ................................................................................................ 3-1
Basic Fax Operation ...................................................................................... 3-2
Sending a Fax Using the ADF..................................................................... 3-2
Sending a Fax Using the Original Glass ..................................................... 3-5
Selecting the Image Quality .......................................................................... 3-7
Selecting the Original Quality...................................................................... 3-7
Selecting the Scan Density ......................................................................... 3-8
Specifying a Recipient ................................................................................... 3-9
Directly Entering a Fax Number .................................................................. 3-9
Using the Favorite List .............................................................................. 3-10
Using the Speed Dial Function ................................................................. 3-10
Using the List Function of the Address Book ........................................... 3-11
Using the Search Function of the Address Book......................................3-12
Using the Redial Function......................................................................... 3-13
Specifying Multiple Recipients ................................................................... 3-14
Sending a Fax to Multiple Recipients (Broadcast Transmission) ............. 3-14
Sending a Fax to Multiple Recipients (Group Dial) ................................... 3-16
Sending a Fax at a Specified Time (Timer Transmission) ........................3-17
Sending a Batch Transmission ................................................................... 3-19
Memory Transmission and Direct Transmission ......................................3-20
Memory Transmission............................................................................... 3-20
Direct Transmission .................................................................................. 3-20
Changing the Transmission Method ......................................................... 3-20
Sending a Fax Manually .............................................................................. 3-22
Sending a Fax Manually After Using the Telephone.................................3-22
Sending a Fax Manually Using the On Hook Key ..................................... 3-23
Sending a Fax to a Combination of Fax Numbers (Chain Dial) ............... 3-24
Cancelling a Queued Transmission ...........................................................3-25
About the Fax Header ................................................................................. 3-26
4 Faxing From a Computer (PC-FAX) .............................................................. 4-1
Sending a Fax Directly From a Computer (PC-FAX) ...................................4-2
PC-FAX Settings ............................................................................................ 4-2
Common Buttons........................................................................................ 4-2
Settings Tab................................................................................................ 4-2
Sender Information Tab .............................................................................. 4-2

Contents x-5
Address Book Tab ...................................................................................... 4-3
Displaying PC-FAX Settings .........................................................................4-4
Windows 7/Server 2008 R2 ........................................................................ 4-4
Windows Vista/Server 2008........................................................................ 4-4
Windows XP Home Edition ......................................................................... 4-4
Windows XP Professional/Server 2003 ...................................................... 4-4
Basic PC-FAX Transmissions ....................................................................... 4-5
Uninstalling the FAX Driver (for Windows) ..................................................4-6
5 Receiving Faxes ............................................................................................. 5-1
Receiving Faxes Automatically .................................................................... 5-2
Receiving Faxes Manually ............................................................................ 5-3
Manual Reception....................................................................................... 5-3
Receiving Faxes With an Operation Performed by This Machine (Manual Poll-
ing Reception)............................................................................................. 5-4
Forwarding Received Faxes ......................................................................... 5-4
Printing Received Faxes ............................................................................... 5-5
What Is the Guaranteed Imageable (Printable) Area?................................. 5-5
Printing Received Faxes on Both Sides of Paper....................................... 5-5
Adding the Sender’s Information When Printing Faxes.............................. 5-6
Method of printing during reception ........................................................... 5-7
REDUCTION RX: ON ............................................................................ 5-7
REDUCTION RX: OFF........................................................................... 5-9
REDUCTION RX: CUT ........................................................................ 5-11
6 Registering Recipients .................................................................................. 6-1
About the Dial Register Function ................................................................. 6-2
Favorite List .................................................................................................... 6-3
Registering Destinations in the Favorite List............................................... 6-3
Deleting Destinations from the Favorite List............................................... 6-4
Speed Dialing ................................................................................................. 6-5
Registering a Speed Dial Destination ......................................................... 6-5
Changing/Deleting Speed Dial Information.................................................6-7
Group Dialing ................................................................................................. 6-8
Registering a Group Dial Destination.......................................................... 6-8
Changing/Deleting Group Dial Information............................................... 6-10
7 Confirmation Mode ........................................................................................ 7-1
About the Machine’s Counters .....................................................................7-2
Checking the Counter for Fax Printing ....................................................... 7-2
Checking the Counter for Total Scans........................................................ 7-2
Checking the Transmission/Reception Result From the Message Window .
7-3
About the Reports and Lists ......................................................................... 7-4
Printing the Reports and Lists .................................................................... 7-4
TX RESULT REPORT.................................................................................. 7-4

Contentsx-6
RX RESULT REPORT.................................................................................. 7-5
ACTIVITY REPORT ..................................................................................... 7-5
MEMORY DATA LIST.................................................................................. 7-5
MEMORY IMAGE PRINT ............................................................................ 7-6
FAVORITE LIST........................................................................................... 7-6
SPEED DIAL LIST ....................................................................................... 7-6
GROUP DIAL LIST ...................................................................................... 7-6
8 Troubleshooting ............................................................................................. 8-1
Problems When Sending Faxes .................................................................... 8-2
Problems When Receiving Faxes ................................................................. 8-3
Other Problems .............................................................................................. 8-4
Error Messages on the Message Window ................................................... 8-5
9 Appendix .........................................................................................................9-1
Technical Specifications ............................................................................... 9-2
Entering Text .................................................................................................. 9-4
Key Operation ............................................................................................. 9-4
Entering Fax Numbers .......................................................................... 9-4
Entering Names .................................................................................... 9-5
Entering Email Addresses..................................................................... 9-5
Changing Input Mode ................................................................................. 9-6
Inputting Example ....................................................................................... 9-6
Correcting Text And Input Precautions ...................................................... 9-7

1
Introduction

Machine Parts1-2
Machine Parts
The parts of the machine referred to throughout this manual are illustrated
below. Please take some time to become familiar with them.
Front View
1 Control panel
2 Automatic Document Feeder
(ADF)
2-a ADF feed cover
2-b Document guide
2-c Document feed tray
2-d Extension tray
2-e Document output tray
2-f Document stopper
d The ADF may appear as
“document cover” in some
status and error messages.
d Lower the document stopper
when scanning Legal-size
paper with the ADF.
3 USB HOST port
4 Tray 1 (Manual feed tray)
5 Tray 2
6 Original cover pad
7 Original glass
8 Extension tray
9Outputtray
10 Scanner unit
&
'

$
%
4
5
1
2-a
2-c
2
2-d
2-e
2-f
3
2-b

Machine Parts 1-3
Rear View
1 10Base-T/100Base-TX/
1000Base-T (IEEE 802.3) Ether-
net interface port
2USBport
3 Power switch
4 Power connection
5 LINE (telephone line) jack
6 TEL (telephone) jack
7Rearcover
!"
%
#

$

Machine Parts1-4

2
Control Panel and
Configuration
Menu

About the Control Panel2-2
About the Control Panel
No. Part Name Description
1Addressbook
key
-Displays the information registered in the favor-
ite list, speed dial destinations and group dial
destinations.
-For details, refer to “Specifying a Recipient” on
page 3-9.
2Auto RX indica-
tor
-Lights up when the automatic receiving func-
tion is selected.
-For details, refer to “Receiving Faxes Automati-
cally” on page 5-2.
3 Message window Displays settings, menus, and messages.
4Error indicator -Indicates an error condition.
-For details, refer to “Error Messages on the
Message Window” on page 8-5.
5Fax key/LED -Enters Fax mode.
-Lights up in green to indicate that the machine
is in Fax mode.
-For details, refer to “Fax Mode Screen” on
page 2-5.
 " # $ % &!
 '"#$& !
% 
"

About the Control Panel 2-3
6Scan key/LED -Enters Scan mode (Scan to E-mail, Scan to
FTP, Scan to a shared folder on a computer,
Scan to PC, or Scan to USB Memory).
-Lights up in green to indicate that the machine
is in Scan mode.
-For details, refer to the [Printer/Copier/Scanner
User’s Guide] on the Documentation CD/DVD.
7Copy key/LED -Enters Copy mode.
-Lights up in green to indicate that the machine
is in Copy mode.
-For details, refer to the [Printer/Copier/Scanner
User’s Guide] on the Documentation CD/DVD.
8Stop/Reset key Returns the settings to their defaults and stops
functions.
9Start (Color) key Starts color copying, scanning or faxing.
10 Start indicator -Lights up in blue when copying and fax trans-
mission are possible.
-Lights up in orange when copying and fax
transmissions are not possible, for example,
during warm-up or if an error has occurred.
11 Start (B&W) key Starts monochrome copying, scanning or faxing.
12 Keypad -Enters desired number of copies.
-Enters fax numbers, mail addresses, and
names of recipients.
-For details on entering text, refer to “Entering
Text” on page 9-4.
13 Back key -Clears the specified number of copies and
entered text.
-Press to return to the previous screen.
-Press to cancel the setting that is currently dis-
played.
14 */)keys Moves left and right through menus, options, or
choices.
15 Select key Press to select the setting that is currently dis-
played.
No. Part Name Description

About the Control Panel2-4
16 +/,keys Moves up and down through menus, options, or
choices.
17 On hook key -Sends and receives transmissions with the
receiver on the hook.
-For details, refer to “Sending a Fax Manually
Using the On Hook Key” on page 3-23 or
“Receiving Faxes Manually” on page 5-3.
18 Redial/Pause
key
-Recalls the last number dialed.
-Inserts a pause when a number is dialed.
-For details, refer to “Using the Redial Function”
on page 3-13.
No. Part Name Description

Fax Mode Screen 2-5
Fax Mode Screen
Main Screen
No. Indication Description
1 Time Displays the time currently specified with [ADMIN.
MANAGEMENT]/[USER SETTING]/[DATE&TIME]
in the [UTILITY] menu.
2Availablemem-
ory
Indicates the percentage of memory available for
scanning and fax operations.
3 Fax settings Allows the current settings to be checked and the
various settings to be changed. For details, refer
to “Fax settings” on page 2-6.
4 Status Depending on the situation, the machine status or
an error message may appear.

Fax Mode Screen2-6
-Fax settings
No. Indication Description
1 Fax quality Indicates the fax quality that is selected. For
details on selecting the fax quality, refer to “FAX
TX OPERATION Menu” on page 2-19 and “Select-
ing the Image Quality” on page 3-7.
Press +/,
Press +/,
Press +/,

Fax Mode Screen 2-7
2 Fax destination Indicates the specified fax destination. For details
on specifying the destination, refer to “Specifying
a Recipient” on page 3-9 and “Specifying Multiple
Recipients” on page 3-14.
d If no destination has been specified, [FAX
TO] appears.
3 [TIMER TX] Select this menu item to specify the time when the
fax is to be sent. For details on specifying settings
for a timer transmission, refer to “Sending a Fax at
a Specified Time (Timer Transmission)” on
page 3-17.
4 Transmission
mode
Indicates the fax transmission mode that is
selected. For details on the transmission modes,
refer to “FAX TX OPERATION Menu” on page 2-19
and “Memory Transmission and Direct Transmis-
sion” on page 3-20.
5 [CANCEL
RESERV.]
Select this menu item to display the list of jobs
queued for transmission and to delete a job. For
details, refer to “Cancelling a Queued Transmis-
sion” on page 3-25.
d This menu item does not appear if a
destination has been specified.
6 [UTILITY] Select this menu item to change the various
machine settings. For details, refer to “UTILITY
Menu” on page 2-9.
d This menu item does not appear if a
destination has been specified.
7[REPORT/STA-
TUS]
Select this menu item to view the total number of
pages printed by this machine and the results of
fax transmissions/receptions as well as to print
reports. For details, refer to “Confirmation Mode”
on page 7-1.
d This menu item does not appear if a
destination has been specified.
No. Indication Description

Fax Mode Screen2-8
Entering Fax Mode
Before using the Fax function, make sure that the Fax key lits green. Other-
wise, press it to enter the Fax mode.
Pressing the Redial/Pause key or On hook key switches the machine to Fax
mode when it is in any mode other than Fax mode.
Symbol list
Symbol Description
Dialing A fax number is being dialed.
Ringing The machine is being called.
Sending The document is being sent.
Receiving A document is being received.
Number of scan-
ning document
pages
The number of scanning document pages
appears next to the icon.
Tone If Pulse is selected as the telephone line type,
press the key to temporarily change the line
type to Tone.
Pause A pause is inserted.
Queued timer
transmission or
batch transmis-
sion
A document is queued for timer transmission
or batch transmission.
Memory recep-
tion
A document is queued for memory reception.