Olympic Medical BILI-LITE 33 User manual

OLYMPIC MEDICAL
51433-IMA-EN0103Q
Instruction Manual
OLYMPIC BILI-LITETM
Model 33/34
CAUTION
Read and be familiar with this manual before installing,
operating, or servicing this device. To ensure operator,
technician, and patient safety, use only as specified in
this manual.

OLYMPIC MEDICAL
5900 First Ave S
Seattle, WA 98108 USA
Toll-free: 1-800-426-0353 (US/Canada)
Phone: [phone] (worldwide)
Fax: [phone]
Web: www.OlympicMedical.com
© 2005 Olympic Medical Corporation. All rights reserved.

OLYMPIC BILI-LITE Model 33/34 Instruction Manual i
Contents
Section 1Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Irradiance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Section 2Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Assembling the Bili-Lite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Attaching the Tilt Hood Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Installing the Bili-Timer on the Bili-Lite . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Testing the Bili-Lite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Section 3Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Operating the Bili-Lite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Positioning the Light Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Measuring Irradiance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Measuring Treatment Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Section 4Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Section 5Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Replacing the Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Bulb Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Section 6Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Repair Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Repair Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Replacing the Fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Replacing the Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Removing the Light Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Checking the Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Replacing the Bulb Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Replacing the Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Replacing the Ballast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Replacing the Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Returning for Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16

ii OLYMPIC BILI-LITE Model 33/34 Instruction Manual
Section 7Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
Parts and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Section 8Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Electromagnetic Specifications – Manufacturer’s Declaration. . . . . . . . . .8-3
Recommended Separation Distances Between Portable and
Mobile RF Communications Equipment and the Bili-Lite. . . . . . . . . . 8-5
Appendix ADrawings and Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

OLYMPIC BILI-LITE Model 33/34 Instruction Manual 1-1
Section
1
Overview
This manual provides the necessary information to install, maintain, and service
the Olympic Bili-LiteTM Model 33/34. The operating instructions in this manual are
intended for use under the direct supervision of a licensed medical practitioner.
The installation and service instructions in this manual are intended for use by
qualified service technicians.
Conventions
The following conventions are used in this manual.
Table 1.1 Conventions
Convention Description
NOTE
#Notes provide additional information to clarify a point in the text.
CAUTION
Cautions indicate situations that, if not avoided, could result in minor
to moderate injury to the patient or operator, or damage to the equipment.
WARNING
Warnings indicate situations that, if not avoided, could result in
serious injury or death to the patient or operator.
BUTTON
This character style represents buttons and controls that the user
can touch or press.

1-2 OLYMPIC BILI-LITE Model 33/34 Instruction Manual
Symbols
Symbols
The following symbols are located on the Olympic Bili-Lite and its packaging.
Table 1.2 Symbols on the Bili-Lite
Symbol Definition Symbol Definition
Alternating current (ac)
voltage
Line (hot conductor)
Atmospheric pressure Mains power OFF
Caution, hot surfaces Mains power ON
Caution, read instructions Neutral (neutral conductor)
Electrical shock hazard Nonionizing
electromagnetic radiation
Eye protection to be worn
by infants
Shipping
Fuse Storage
Protective earth (ground) Temperature
Humidity, condensing Type B equipment

OLYMPIC BILI-LITE Model 33/34 Instruction Manual 1-3
Intended Use
Intended Use
The Olympic Bili-LiteTM Model 33/34 is a floorstand phototherapy light intended to
provide therapeutic irradiance to treat neonatal hyperbilirubinemia.
Description
The Olympic Bili-Lite Model 33/34 is a floorstand phototherapy light (see
Figure 1.1). Its light hood is height adjustable from 43 to 59 in. (110 to 151 cm)
above the floor. The Bili-Lite Model 34 includes an Olympic Bili-TimerTM.
The Bili-Lite is equipped standard with eight Olympic Blue (Type OB) fluorescent
bulbs. Other types of fluorescent bulbs are available (see Parts and Accessories on
page 7-1).
Figure 1.1 Bili-Lite Model 33/34
Hood tilt attachment
(optional accessory for
Model 33/34)
Support post
Base
Light hood
Safety shield
Caster wheels
Height adjustment knob
Power cord

1-4 OLYMPIC BILI-LITE Model 33/34 Instruction Manual
Accessories
Accessories
Olympic Medical offers the following items that are compatible for use with the
Bili-Lite Model 33/34:
Olympic Bili-Timer, which precisely times the phototherapy treatment session.
Olympic Bili-MeterTM, which measures the irradiance output of phototherapy.
Olympic Bili-MaskTM, which protects the patient’s eyes during phototherapy
treatment.
To order these items, see page 7-1.
Figure 1.2 Bili-Timer
Figure 1.3 Bili-Meter with Type B22 sensor
Figure 1.4 Bili-Mask styles
“Standard” “Easy-On”“Quick-Stick”

OLYMPIC BILI-LITE Model 33/34 Instruction Manual 1-5
Irradiance
Irradiance
The therapeutic irradiance of phototherapy lights is measured with radiometers,
instruments with optical filters that pass only selected portions of the blue-green
action spectrum of bilirubin. Irradiance (radiant power) is expressed in units of
microwatts per square centimeter per nanometer (µW/cm²/nm).
The Olympic Bili-Meter1—the radiometer widely used in nurseries—measures
irradiance from 425 to 475 nanometers (nm). Standard 60601-2-50 of the
International Electrotechnical Commission (IEC) also requires that irradiance from
400 to 550 nm be measured. The following tables show this data.
The irradiance data for the Olympic Bili-Lite Model 33/34, below, is shown for
Olympic Blue (Type OB) and Super Blue (Special, Type BB) blue fluorescent
bulbs at varying distances. Average irradiance is measured over an effective
surface area of 12 x 24 in. (30 x 60 cm). Maximum irradiance is measured at the
center of the area.
1. Each Olympic Bili-Meter is certified to be calibrated traceable to the United States National
Institute of Standards and Technology (NIST).
NOTE
#The differences between the Olympic Bili-Meter and the IEC measurements do not
represent a difference in the total irradiance output of the same bulbs. The difference
results from averaging the irradiance of the same bulbs over wavelength bands of different
widths. The Olympic Bili-Meter measures from 425 to 475 nm—nearly all of the irradiance
of blue bulbs occur in this 50-nm band. The IEC measures irradiance from 400 to
550 nm—a 150-nm band; therefore, the average irradiance per nanometer of the IEC
measurement will differ from the Bili-Meter measurement.
Table 1.3 Average irradiance using the Olympic Bili-Meter (425–475 nm)
Distance—bulb shield to top of light sensor
20 in.
(51 cm)
25 in.
(64 cm)
30 in.
(76 cm)
(8) Olympic Blue (Type OB) bulbs 11.9 8.5 6.0
(8) Super Blue (Type BB) bulbs 22.4 16.3 12.3
Table 1.4 Maximum irradiance using the Olympic Bili-Meter (425–475 nm)
Distance—bulb shield to top of light sensor
20 in.
(51 cm)
25 in.
(64 cm)
30 in.
(76 cm)
(8) Olympic Blue (Type OB) bulbs 13.8 9.5 6.4
(8) Super Blue (Type BB) bulbs 26.0 18.2 13.3

1-6 OLYMPIC BILI-LITE Model 33/34 Instruction Manual
Irradiance
Figure 1.5 Response, Olympic Bili-Meter
Table 1.5 Average irradiance using the IEC Standard (400–550 nm)
Distance—bulb shield to top of light sensor
20 in.
(51 cm)
25 in.
(64 cm)
30 in.
(76 cm)
(8) Olympic Blue (Type OB) bulbs 6.0 4.5 3.5
(8) Super Blue (Type BB) bulbs 8.3 6.1 4.6
Table 1.6 Maximum irradiance using the IEC Standard (400–550 nm)
Distance—bulb shield to top of light sensor
20 in.
(51 cm)
25 in.
(64 cm)
30 in.
(76 cm)
(8) Olympic Blue (Type OB) bulbs 7.0 5.0 3.8
(8) Super Blue (Type BB) bulbs 9.6 6.8 5.0
0
10
20
30
40
50
60
70
80
90
100
390 400 410 420 430 440 450 460 470 480 490 500 510 520
Wavelength (nm)
Relative Response (%)

OLYMPIC BILI-LITE Model 33/34 Instruction Manual 1-7
Irradiance
Figure 1.6 Spectral energy distribution, Olympic Blue (Type OB) bulb
Figure 1.7 Spectral energy distribution, Super Blue (Type BB) bulb
Wavelength (nm)
Relative irradiance (µW/cm²)
Wavelength (nm)
Relative irradiance (µW/cm²)

1-8 OLYMPIC BILI-LITE Model 33/34 Instruction Manual
Irradiance
Figure 1.8 Effective surface area, Olympic Bili-Lite Model 33/34
Effective Surface Area
(view from above)
Light Hood Area
26 in. (66 cm)
24 in. (60.9 cm)
12 in. (30.5 cm)
19 in. (48.3 cm)

OLYMPIC BILI-LITE Model 33/34 Instruction Manual 2-1
Section
2
Assembly
Assembling the Bili-Lite
The Bili-Lite Model 33 is shipped with the following items. The Model 34 also
includes an Olympic Bili-TimerTM (for installation, see page 2-7).
Light hood with safety shield
Support post with arm and power cord
Base assembly
Caster wheels
Hardware packet with 3/8-in. grade-8 mounting bolt and two spare starters
Bulbs (eight Type OB)
Required Items:
Major assemblies, as listed above
Medium-size adjustable wrench
Phillips-head screwdriver
Scissors or utility knife
To assemble the Bili-Lite:
1Install the caster wheels:
aPlace the base with the bottom facing up.
bScrew the casters into the base, then tighten.
2Set the base on a level floor, then mount the support post on the base (see
Figure 2.1 on page 2-2).
3Insert and securely tighten the mounting bolt from underneath the base (see
Figure 2.1), to secure the support post.
CAUTION
Only qualified technicians should assemble this device.
Read and be familiar with this instruction manual before assembling this device.
CAUTION
Firmly tighten the mounting bolt to preserve the stability of the Bili-Lite.

2-2 OLYMPIC BILI-LITE Model 33/34 Instruction Manual
Assembling the Bili-Lite
Figure 2.1 Bili-Lite assembly, without tilt assembly
Knobs (x3)
Cord clamp
Power cord
Support post
Base
Light hood
Height adjustment knob
Mounting bolt
Safety shield
Caster wheels (x4)
Bulb life timer
Support post arm

OLYMPIC BILI-LITE Model 33/34 Instruction Manual 2-3
Assembling the Bili-Lite
4Fully tighten the height adjustment knob, then cut the safety string.
5Slowly and carefully release the height adjustment knob until the support post is
at its full extension, then tighten the knob again.
6Remove the three knobs from the bolts on top of the light hood (see Figure 2.1).
7Lift the light hood, then insert the bolts on top of the light hood through the
holes in the horizontal arm of the support post (see Figure 2.1).
8Reinstall the knobs on the bolts and tighten.
9Remove the plastic cord clamp from the support post (see Figure 2.1).
10 If you are adding a tilt assembly, perform the hood tilt assembly steps now (see
page 2-4). Once the hood tilt attachment is installed, continue to step 11.
11 Slip the power cord into the clamp and reinstall it on the support post. Leave
approximately 28 in. (71 cm) of slack in the cord above the clamp to allow
for adjustment.
12 Remove the safety shield by removing the retaining screws and washers. Then
gently slide the shield out (see Figure 2.3).
13 Remove the protective covering from the safety shield.
14 Install the bulbs: For each new bulb insert the prongs into the socket, then
carefully rotate the bulb into place.
15 Insert the safety shield, place the washers, then tighten the retaining screws.
16 Test for proper operation (see page 2-8).
WARNING
The spring inside the support post is compressed; releasing the height adjustment
knob will permit the support post to extend suddenly and forcefully to a distance of
16 in. (40.6 cm). Fully tighten the height adjustment knob before cutting the string.
While securely holding the support post, carefully release the knob.
CAUTION
The light hood is heavy and awkward. A second person should help support the light hood
while installing or removing it.
CAUTION
The safety shield must always be in place during phototherapy to protect the patient from
ultraviolet radiation and broken bulbs.

2-4 OLYMPIC BILI-LITE Model 33/34 Instruction Manual
Attaching the Tilt Hood Assembly
Attaching the Tilt Hood Assembly
A tilt assembly can also be added to a Model 33/34. To order a tilt assembly, see
Ordering Information on page 7-1.
Required Items:
Tilt hood assembly, which includes adhesive
Medium-size adjustable wrench
Phillips-head screwdriver
Nutdriver, slim-profile preferred
To attach the tilt hood assembly:
1If adding a tilt assembly while assembling your new Model 33/34, perform
steps 2–6 starting on page 2-1, then perform the hood tilt assembly steps below.
–or–
If adding the tilt hood assembly to your assembled Model 33/34, press the
power switch to the Off (O) position, unplug the power cord, perform the
steps 6–9 starting on page 2-1, then perform the hood tilt assembly steps below.
2Place the tilt hood bar, with the large holes facing down and the side holes
toward the front of the light hood, on top of the light hood (see Figure 2.2).
Figure 2.2 Placing the tilt hood bar
3Insert the three hood bolts up, through the light hood, through the bar and secure
with lock nuts (see Figure 2.3). Affix fastener caps over the lock nuts using the
small tube of Loctite®401 supplied in this kit.
NOTE
#The adjustment screw assembly and the pivot assembly are shipped with their mounting
fasteners loosely assembled. They may be disassembled as required to attach them during
the following steps.
NOTE
#If you do not have a slim-profile nutdriver or socket, you might not be able to reach inside
the square tubing to install the lock nuts. You may instead install these brackets with the
mounting screws placed inside the support post arm and the lock nut on top of the bar. After
assembly is complete the five extra fastener caps supplied with this kit may be affixed over
the lock nuts using the small tube of Loctite®401 supplied with this kit
Light hood
FRONT
Tilt hood bar
Lock nuts, securing hood bolts (x3)
Power cord
BACK of light hood
Side holes (x2) at
front of light hood

OLYMPIC BILI-LITE Model 33/34 Instruction Manual 2-5
Attaching the Tilt Hood Assembly
4Place Bracket A on the support post arm. Bracket A is the bracket facing the
O-ring side of the adjustment knob. There is an acorn nut and lock washer
permanently secured to the adjustment screw through this bracket.
5Slide the adjustment screw into the Bracket A.
6Place the rubber O-ring on the front end of the adjustment screw (see
Figure 2.3).
7Screw adjustment knob all the way onto the screw, to the O-ring.
Figure 2.3 Mounting Bracket A and the adjustment screw
8Mount the pivot bracket on the support post arm (see Figure 2.4).
9Fasten the light hood to the pivot bracket with the pin (see Figure 2.4), then
place the washers and secure the lock nuts.
10 Affix fastener caps over the lock nuts using the small tube of Loctite 401
supplied with this kit.
Figure 2.4 Mounting the pivot bracket
Bracket A
O-ring
Adjustment screw
Adjustment knob
Support post
Support arm
NOTE: Exploded view shown for
information only. The nut will
already be attached to Bracket A
and the adjustment screw.
CAUTION
The light hood is heavy and awkward. A second person should help support the light hood
while installing or removing it.
Pivot bracket
Support arm
Pivot bracket
Support arm
Light hood
Tilt hood bar
NOTE: Some Bili-Lites may
require the screws to be inserted
from below the support arm, with
nuts placed on the top.
Pin

2-6 OLYMPIC BILI-LITE Model 33/34 Instruction Manual
Attaching the Tilt Hood Assembly
11 Hold the light hood in position under the support post arm, then slide the bale
under the adjustment screw (see Figure 2.5) and hook the ends into the side
holes of the tilt hood bar.
Figure 2.5 Placing the bale
12 To secure the light hood to the support post arm, attach Bracket B (see
Figure 2.6). The end of the adjustment screw fits through the opening in the
vertical face of Bracket B. Fasten with the screws and lock nuts provided.
Secure the adjustment screw with the lock nut provided.
13 Confirm that all nuts are securely tightened.
14 The tilt assembly is installed with the hood in its lowest position, with the
adjustment knob should be in the full-forward position (see Figure 2.6).
15 To continue assembly, proceed to step 11 on page 2-3.
Figure 2.6 Mounting Bracket B
Support arm
Tilt hood bar
Bale
Adjustment screw
Bracket B
Support arm
NOTE: Some Bili-Lites may
require the screws to be inserted
from below the support arm, with
nuts placed on the top.