Omega Altise OAPC1217 User manual

OAPC1217
PORTABLE AIR CONDITIONER

2
Table of Contents
Table of Contents..........................................................................2
Important Safeguards................................................................... 3-4
Placement and Installation............................................................5-6
Parts List....................................................................................... 6-7
Control Panel................................................................................8
Remote Control..............................................................................9
Operation Methods........................................................................9-10
Water Drainage.............................................................................11
Maintenance.................................................................................12
Troubleshooting........................................................................... 13
Technical Data............................................................................. 14
Circuit Diagram ...…………………………………..….….... Appendix A

3
Important Safeguards
Please read this manual
Inside you will find many helpful hints on how to use and maintain your air
condition properly. Just a little preventative care on your part can save you a
great deal of time and money over the life of your air condition. You will find
many answers to common problems inside this manual.
CAUTION
• Contact the authorised service centre for repair of this air condition
• This air condition is not intended for use by young children or infirm
persons, without Supervision.
• Young children should be supervised to ensure that they do not play with the
appliance.
• If the power cord is damaged it must be repaired by an authorised agent of
Omega Altise
SAFETY RULES
To prevent injury to the user or other people and to prevent property damage,
the following instructions must be followed. Incorrect operation due to not
reading the instructions may cause harm or damage.
• Yourair air condition should be used in such a way that it is
protected from moisture (e.g. condensation or water) do not store or
place the air condition where it can fall from an elevated surface.
• Always transport the air condition in a vertical position and stand it on
a stable, level surface during operation.
• Turn off the air condition when not in use.

4
• Always contact an authorized qualified service agent to carry out repairs.
• If the supply cord is damaged it must be repaired by a qualified repairer
• Keep the area clear around the air condition. There needs to be an air path of a
minimum of 50cm all around the air condition from walls, furniture andcurtains.
• If the air condition is knocked over during use turn off the air condition and
unplug it from the power point.
• Do not operate the air condition in a wet room such as a bathroom or laundry
• Do not touch the air condition with wet hands
• Do not press buttons on the air condition with anything but fingers.
• Do not remove fixed covers. Do not use this air condition if it is
malfunctioning or has been dropped or damaged
• Never use the power point switch to start or stop the air condition. Use the
control panel first.
• Do not obstruct the inlet or outlet grills
• Do not use harsh chemicals to clean the air condition.
• Do not run the air condition near dangerous chemicals and or hazardous
chemicals.
• Do not use this air condition for functions other than those described in this
instruction manual.
ENERGY SAVING
• Use the air condition in the recommended room size
• Locate the air condition where furniture cannot obstruct air flow
• Keep blinds and curtains closed to keep out the sun
• Keep the filters clean
• Keep doors and windows closed to keep cool air in and hot air out

5
Placement
Placement and Installation
Place the on flat and dry ground, and keep at least 50 cm from walls etc
(figure 1)
Installation
• Spin slide bar connector into exhaust hose first, then spin the exhaust hose into
exhaust connector (counter-clockwise).
• Put slide bar connector into adjustable slide bar, adjust window open width in
order slide bar match window well, and the length of slide bar is adjustable.
(figure 2)
FIGURE 1
Installation Errors
• Free access of exhaust pipe is important, If air is not taken out it will affect
performance of theappliance.
• Avoid sharp bends in the exhaust-pipe (figure2)
• Make sure air in exhaust pipe can run smoothly (figure 3)

6
FIGURE 2 FIGURE 3
Warning
Use only the exhaust pipe supplied. Longer or extended pipes may damage the
appliance
Note: Maximum length of unfolding exhaust pipe is 1500mm, please shorten the
length as much as possible and keep it level as much as possible when
installing

7
Parts List

7
Control Panel
NOTE: Above blue background color represents the display on the unit when turned on.
1. TIMER: under power-on or standby mode, press this key to setup on/off time from
1~24.
2. FAN: after air condition turns on, press this key to select fan speed (high, medium
and low).
3. UP: under cooling mode, press this key to increase the temperature from 16 -
31C°, under timer mode, press this key to increase the hoursdisplayed.
4. DISPLAY WINDOW: Display window will show the temperature and mode setting
when the air condition isoperational.
5. DOWN: under cooling mode, press this key to decrease setting temperature from
16 - 31C°, under timer mode, press this key to decrease the hoursdisplayed.
6. MODE: after air condition turns on, press this key to select cooling, fanordehumidifymode.
7. POWER: press this key to turn the air condition On/Off. After the aircondition
turns on, default value is cooling mode with low fanspeed.
NOTE: Once the air condition has been operated, it will revert to the settings prior
to it being switched off.
8
1
2
3
4
5
6

9
Remote Control
Cooling mode Operation Methods
• After the air condition turns on, it will revert to the setting that was last used.
• Press “MODE” to select cooling mode, cooling mode inductor turns on.
• Press “UP” or “DOWN” to adjust temperature (from 16 to 31 ).
• Press “FAN” to select high, medium or low fan speed.
Fan mode
• Press “MODE” to select fan mode, fan mode indicator turns on.
• Press “FAN” to select high, medium and low.
• Temperature and sleep function cannot be setup.

10
Timer mode
•
Select the timer mode by pressing , then use the and
buttons to adjust hours from 1-24. You can only set the auto-shut
off timer while the air condition is operating (on) You can only set the auto-
start timer while the air condition is switched off (standby) After you have set
the timer it will initiate and the air conditions will start/ stop after the selected
time. If you adjust the timer or press the power key previous settings will be
cleared. Timer functions cannot be combined or repeated.
Dehumidifying mode
• Press “MODE” to select dehumidifying mode, dehumidifying mode indicator
turns on.
• Under dehumidifying mode fan speed is low.
Sleep mode
• In the cooling Mode, Press the “UP” and “FAN” buttons together to turn on
the sleep mode, then the air condition will work on Energy-Saving and
lowest fan mode.
Compressor protection
If turned ON/OFF/ON at startup it takes 3 minutes for the compressor to
start.