Omega Altise OAPC127 User manual

OAPC127
PORTABLE AIR CONDITIONER

2
Table of Contents
Table of Contents..........................................................................2
Important Safeguards................................................................... 3-4
Placement and Installation............................................................5-6
Parts List....................................................................................... 6-7
Control Panel................................................................................8
Remote Control..............................................................................9
Operation Methods........................................................................9-10
Water Drainage.............................................................................11
Maintenance.................................................................................11-12
Troubleshooting............................................................................ 13
Technical Data...............................................................................14
Circuit Diagram ...…………………………………..….….... Appendix A

3
Important Safeguards
Please read this manual
Inside you will find many helpful hints on how to use and maintain your unit
properly. Just a little preventative care on your part can save you a great deal
of time and money over the life of your unit. You will find many answers to
common problems inside this manual.
CAUTION
• Contact the authorized service center for repair of this unit
• This unit is not intended for use by young children or infirm persons,without
Supervision.
• Young children should be supervised to ensure that they do not play with the
appliance.
• If the power cord is damaged it must be repaired by an authorized agent of
Omega Altise
SAFETY RULES
To prevent injury to the user or other people and to prevent property damage,
the following instructions must be followed. Incorrect operation due to not
reading the instructions may cause harm or damage.
• Yourportable air conditioner unit should be used in such a way thatit
is protected from moisture (e.g. condensation or water) do not store
or place the unit where it can fall from an elevated surface.
• Always transport the unit in a vertical position and stand it on astable,
level surface during operation.
• Turn off the unit when not in use.

4
• Always contact an authorized qualified service agent to carry out repairs.
• If the supply cord is damaged it must be repaired by a qualified repairer
• Keep the area clear around the unit. There needs to be an air path of a
Minimum of 50cm all around the unit from walls, furniture andcurtains.
• If the unit is knocked over during use turn off the unit and unplug it from the
power point.
• Do not operate the unit in a wet room such as a bathroom or laundry
• Do not touch the unit with wet hands
• Do not press buttons on the unit with anything but fingers.
• Do not remove fixed covers. Do not use this unit if it is malfunctioning or has
been dropped or damaged
• Never use the power point switch to start or stop the unit. Use the control panel
first.
• Do not obstruct the inlet or outlet grills
• Do not use harsh chemicals to clean the unit.
• Do not run the unit near dangerous chemicals and or hazardouschemicals.
• Do not use this unit for functions other than those described in thisinstruction
manual.
ENERGY SAVING
• Use the unit in the recommended room size
• Locate the unit where furniture cannot obstruct air flow
• Keep blinds and curtains closed to keep out the sun
• Keep the filters clean
• Keep doors and windows closed to keep cool air in and hot air out

5
Placement
Placement and Installation
Place the on flat and dry ground, and keep at least 50 cm from walls
etc. (figure 1)
Installation
• Spin slide bar connector into exhaust hose first, then spin the exhaust hose into
exhaust connector (counter-clockwise).
• Put slide bar connector into adjustable slide bar, adjust window open width in
order slide bar match window well, and the length of slide bar is adjustable.
(figure 2)
FIGURE 1
Installation Errors
• Free access of exhaust pipe is important; If air is not taken out it will affect
performance of theappliance.
• Avoid sharp bends in the exhaust-pipe (figure2)
• Make sure air in exhaust pipe can run smoothly (figure 3)

6
FIGURE 2 FIGURE 3
Warning
Use only the exhaust pipe supplied. Longer or extended pipes may damage the
appliance
Note: extreme length of unfolding exhaust pipe is 1500mm, please shorten the
length as much as possible and keep it level as much as possible when
installing

7
Parts List

8
Control Panel
1. POWER: press this key to turn unit On or Off. After unit turns on, default value iscooling
mode with low fan speed.
2. OPERATION MODE BUTTON: after unit turns on, for cooling only model, press this
key to select the other modes: Fan, Dry/dehumidify, Cool orAuto.
3. FAN SPEED: after unit turns on, press this key to select between 3 fan speeds (high, medium or low).
4. DOWN: under cooling mode, press this key to downward setting temperaturefrom
16~31˜ ; under timer mode, press this key to downward on/offtime.
5. UP: under cooling mode, press this key to upward temperature from 1 6 ~31˜; under timer
mode, press this key to upward on/offtimer.
6. SLEEP: under cooling, press this key to turn on/off sleep function.
7. ON/OFF TIMER: When the unit is in standby/off mode press Timer to between 1 -24 hours
and it will turn on after selected time isreached.
When the unit is in On mode press the timer to between 1 –24 hours and it will
Turn off after the selected time is reached.
NOTE: Once the unit has been operated, the unit will revert to the settings prior to it being
switched off.
Operation

9
Remote Control
Operation Methods
Auto Mode
According to the current room temperature, once you select AUTO it
automatically selects the relevant mode.
Cooling Mode
• After machine turns on, the unit will revert to setting that was lastused.
• Press “OPERATING MODE BUTTON”” to select cooling mode, once this option
is selected cooling mode inductor turns on.
• Press “UP” or “DOWN” to adjust temperature (from 16 31 .
• Press “FAN Speed Button” to select high, Medium or low fan speeds.
Fan Mode
• Press “OPERATING MODE BUTTON” to select fan mode, once this option is
selected fan mode indicator will turn on.
• Press “FAN Speed Button” to select high, Medium or low fan speeds.
• Temperature and sleep function cannot be setup in thismode.

10
Timer Mode
• When in off/ standby, press "TIMER" to setup the power-on timer, press
"UP or "DOWN" to adjust the timer (from 1-24 hours) press "TIMER"to
confirm selection.
• "Under power-on mode, press "TIMER" to setup power-off, Press "UP
or "DOWN" to adjust the timer (from 1-24 hours) press "TIMER" to
confirm selection
Dry/ Dehumidifying Mode
• Press “OPERATING MODE BUTTON” to select dehumidifying mode, once
this option is selected dehumidifying mode indicator turnson.
• Under dehumidifying mode fan speed is low.
• Temperature and sleep function cannot be setup in thismode.
Sleep Mode
• Press “SLEEP” to enter into sleeping mode, default value of fan speed is
low.
• Sleep mode is invalid under dehumidifying and fan mode. Under water full,
machine standby and mode conversion, sleep mode will be cancelled.
Compressor Protection
If turned ON/OFF/ON at startup it takes 3 minutes for the compressor to
start.