Omni-Rinse AUTO-BURN ICE BIN Original operating instructions

USE AUTO-BURN™ ONLY AS INSTRUCTED IN THIS MANUAL.
THIS MANUAL DOES NOT COVER EVERY POSSIBLE CONDITION AND
SITUATION THAT MAY OCCUR. USE COMMON SENSE AND CAUTION
WHEN INSTALLING, OPERATING, AND MAINTAINING THIS DEVICE.
CLOGGED ICE BIN DRAIN LINES AND FLOOR SINKS/DRAINS MAY CAUSE
FLOODING. MAINTAIN ICE BIN DRAIN LINES AND FLOOR SINKS/DRAINS
TO AVOID FLOODING.
ALWAYS INSTALL SECONDARY SHUTOFF VALVE (F) IN ADDITION TO
PRIMARY CONTROL VALVE (G). FAILURE TO DO SO VOIDS WARRANTY.
WATER STREAM FROM AUTO-BURN™ IS HOT! DIRECT CONTACT WITH
WATER STREAM MAY CAUSE SCALDING!
AUTO-BURN™ IS NOT INTENDED TO BE A SUBSTITUTE FOR WASHING,
DRYING, & SANITIZING ICE BINS. FOLLOW PROPER HEALTH CODE
PROCEDURES. REGULARLY WASH & SANITIZE ICE BINS.
MISUSE MAY CAUSE FLOODING OR WATER DAMAGE! ENSURE THAT
VALVE IS TURNED COMPLETELY OFF AFTER USE!
SAFETY
READ THIS MANUAL BEFORE OPERATING!
AUTO-BURN TM
INSTALLATION & OPERATION GUIDE
- Installation by licensed plumber is recommended.
- Always follow appropriate plumbing code.
REV. 22.01.09 Copyright© Omni-Rinse, LLC 2022. All Rights Reserved
ICE BIN

C
Secure Ball Valve to
Water Inlet
D
REV. 22.01.09 Copyright© Omni-Rinse, LLC 2022. All Rights Reserved
1Assembly
AFlip unit over to insert legs.
Secure with 4mm Hex Key.
B
Attach appropriate drain
connector to 1" OD drain fitting
Adjust feet to stabilize and level unit
EProceed to sections 2 and 3 for directions on connecting
ice bin to hot water with included Installation Kit.
Ball Valve
Water Inlet

Direct
Connection
(3/8 compression)
Rigid Supply
Line
Connect fittings
C-G with
included LLDPE
tubing (I).
Option 2
Shutoff (F) and Control
Valve (G) should be easily-
accessible.
Auto-Burn™ Plumbing Installation Diagram
Make final connection
to Auto-Burn™.
*Backflow Preventer not included with AB-BSM1
Tap into hot water line
with correct tee (A or B).
or,
Directly connect hot
water supply valve to
Adapter Fitting (C).
Connect Adapter
Fitting (C) to A or
B. Do not over-
tighten.
For Option 3,
skip to Step 3.
F G
A
BC
Use PTFE tape and/or thread
sealant rated safe for
polypropylene when connecting
Male Adapter Fittings (D) to
Backflow Preventer (E).
D DE
I
Step 1
Option 1
Option 3
Step 2 Step 3 Step 4
Arrows Indicate Hot Water Flow
Flexible Supply
Line
3
NEEDED FOR INSTALLATION:
A. 3/8 Adapter Tee
B. 3/8 Compression Tee
C. 3/8 Push-Fit Adapter
D. (2) Male Push-Fit Adapters (Saddle
Mount Unit and Ice Bin ONLY)
E. Backflow Preventer (Saddle Mount Unit
and Ice Bin ONLY)
F. Inline Shutoff Valve
G. Control Valve (style varies with ice bin)
H. Plug Elbow (Backsplash Mount ONLY)
I. 3/8 LLDPE Tubing
Installation Kit Parts List
* H not included with AB-CH1 or AB-IB1
** D and E not included with AB-BSM1
Flexible Tubing
Cutter
Adjustable
Wrenches
PTFE Tape/Thread Sealant
rated for polypropylene
ABC
D E
FGH
I
2
4MM
Hex Key
Fittings/Tubing
for drain line
REV. 22.01.09 Copyright© Omni-Rinse, LLC 2022. All Rights Reserved

Turn Control Valve (G) counterclockwise to turn water on--adjust stream
accordingly. 
Ensure ice bin and floor sink/drain are properly draining water.
Test Shutoff Valve (F) by turning it off and back on.
Turn Control Valve (G) clockwise to OFF position and confirm that it is
not leaking.
Installation is now complete. Deliver this Operation Guide to customer.
TESTING
1.
2.
3.
4.
5.
Visit OmniRinse.com for more information
TurnControl Valve (G) counterclockwise to turn Auto-Burn™ Head on.
Make fine adjustments for desired flow. WATER FLOW MAY BE
STRONG, SO ADJUST ACCORDINGLY! WATER IS HOT! DIRECT
CONTACT WITH WATER STREAM MAY CAUSE SCALDING! USE
CAUTION AND COMMON SENSE AT ALL TIMES!
After use, turn Control Valve (G) clockwise to OFF position.
After ice has melted, confirm that all debris or foreign objects have
been removed by COMPLETELY DRYING ICE BIN WITH A CLEAN
SQUEEGEE AND/OR TOWEL!
AUTO-BURNING™ ICE IS NOT A SUBSTITUTE FOR WASHING,
RINSING, SANITIZING, & DRYING ICE BINS.
WARNING: FLOODING MAY OCCUR IF DRAIN LINES ARE CLOGGED!
Use Auto-Burn™ daily to help keep ice bins clean and free of harmful
debris and contaminants.
If Control Valve (G) fails, turn unit off with Shutoff Valve (F) to replace
Control Valve.
1.
2.
3.
4.
5.
6.
7.
(Refer to Plumbing Installation Diagram)
OPERATION INSTRUCTIONS
REV. 22.01.09 Copyright© Omni-Rinse, LLC 2022. All Rights Reserved