Omnigates 31001078 User manual

User’s Manual
MINI 3G HDMI®to SDI CONVERTER
SKU: 31001078

Thank you for purchasing Mini 3G HDMI®to SDI Converter. For optimum performance
and safety, please read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
INTRODUCTION
The MINI HDMI to SDI Converter allows HDMI signals to be shown on SDI display while
ensuring high bit rates of 2.970 Gbit/s to give you high resolution signal without any loss.
For professionals this means that it is now easier to convert your high def HDMI signal
with audio to SDI for long distance transmission and display your work on SDI display.
FEATURES
1. Shows HDMI source on SDI display
2. SDI interface operates at bitrates of 2.970 Gbit/s, 2.970/1.001 Gbit/s, 1.485 Gbit/s,
1.485/1.001 Gbit/s and 270 Mb/s
3. Supports HDMI input timings: 480i@59.94, 576i, 720p@50/59.94/60, 1080i@50/
59.94/60, 1080p@23.98/24/25/29.97/30/50/59.94/60
4. Converts HDMI signal to SDI:
∙ 480i/576i to SD-SDI (SMPTE 259M-C, at bitrates of 270 Mbit/s)
∙ 720p/1080i to HD-SDI (SMPTE 292M, at bitrates of 1.485 Gbit/s or
1.485/1.001 Gbit/s)
1

∙ 1080p to 3G-SDI (SMPTE 424M/425M-AB, at bitrates of 2.970 Gbit/s and 2.970/
1.001 Gbit/s)
∙ Supports SDI output distance up to 100 meters (3G-SDI), 200 meters (HD-SDI),
or 300 meters (SD-SDI)
PACKAGE CONTENTS
1x 3G HDMI to SDI Converter
1x 5V DC Power Supply Adapter
User’s Manual
PRODUCT OVERVIEW
1. SDI OUT: Connect with SDI display with coaxial cable
2. Power Indicator - Iluminates when connected to power supply
2
12 3 4

3. DC In - Plug in included power adapter
4. HDMI In - Connect with HDMI devices
CONNECTION DIAGRAM
3
Media Player

SPECIFICATIONS
Input Port
Output Port
SDI Transmission Rates
Resolution
ESD Protection
Dimensions
Weight
Power Consumption
Operating Temperature
Storage Temperature
Relative Humidity
: 1 HDMI
: 1 BNC (SDI/HD-SDI/3G-SDI)
: 2.970 Gbit/s and 2.970/1.001 Gbit/s
: 480i, 576i, 720p@50/59.94,60, 1080i@50/59.94/60,
1080p@23.97/24/25/29.97/30/50/59.94/60
: ±8kV (Air-gap discharge) / ±4kV (Contact discharge)
: 3.1" x 1.6" x 1.0"
: 150g
: 5W
: 32ºF ~ 104ºF (0ºC ~ 40ºC)
: -4ºF ~ 140ºF (-20ºC ~ 60ºC)
: 20 ~ 90% RH (Non-condensing)
4

REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Modifying the equipment without Omnigates’ authorization may result in the equipment no longer complying with FCC requirements
for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be
required to correct any interference to radio or television communications at your own expense.
This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Radio Notice for FCC
Caution
This FCC Part 15 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or
modification to said product not expressly approved by Omnigates, including the use of non-approved antennas, could void the
user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
5