Omnisense Systems Joystick Controller User manual

Jostick Controer
1. What’s in the box
2 X (M5 X 40)
studs, washers,
spring washers
and nuts
Mounting Decal
6.56ft (2m) Cable
Joystick Controller
Mounting Decal
2.13in
(54mm)
2.6 in (66mm)
2.2in (56mm)
0.24in (6mm) diameter
Cutout area
2.17in
(55mm)
2. Installation
The Joystick Controller must be panel mounted. When correctly
installed, the top side (front) of the Joystick Controller is waterproof
and suitable for open deck installation.
When mounting the Joystick Controller, select a location that
provides the best ergonomics for controller operation. The housing
of the Joystick Controller is designed to provide a stable grip while
your thumb or finger moves the knob.
1. The Joystick Controller has a flush back that can be easily
fitted onto any flat surface. Select a suitable location close to
your Multi-function Display (MFD)/Monitor.
2. Using the Joystick Controller Mounting Decal provided, mark
and cut out the space to mount the Joystick Controller.
3. Drill the 0.24in (6mm) holes required for attaching the
Joystick Controller.
4. Mount the Joystick Controller and use the bolts provided to
secure it in place.
3. Connecting the cable
Connect one end of the Joystick Controller Cable to the [Controller]
port in the Junction Box and the other end to the Joystick
Controller.
4. Connecting the Joystick Controller
To connect your Joystick Controller, launch the User Interface (UI).
Proceed to Settings > Controller and select [Scan]. The system
will automatically scan for a Joystick Controller connected to the
Junction Box.
Once the Joystick Controller is found, the serial number will be
displayed. Select to connect the Joystick Controller and it will
be ready for use.
If the system is unable to locate the Joystick Controller, perform a
factory reset to the Joystick Controller by holding down the
and button simultaneously for 10 seconds. Upon completing the
reset, select again to connect the Joystick Controller.

6. Joystick Controller icon description
Below is the description of each icon for further understanding.
Function
Programmable
key
Enter
Confirm selection
Menu
Display menu
options
Zoom
Adjust zoom
Sensor Select
Toggle between
cameras
Color Palette
Select color
mode
Radar Track
Activate tracking
functions
Power/Standby
Wake, park, or
return turret to
home position
Joystick
Menu navigation and
camera control
5. Control buttons
Display controls are accessible by pressing the respective buttons
on the Joystick Controller. To access a setting/function, press the
button marked with the corresponding icon. Use the joystick to
select and cycle through the options available. To wake the camera
from Standby mode, press and hold the Power/Standby button. Joystick
• Move to navigate through menu items
• Adjust Zoom/Focus, Brightness & Contrast
level
• Control camera movement (Pan & tilt)
Enter • Press to confirm a selection
Function
• Programmable Shortcut Key
(Choose from Home, NUC, Standby, Radar)
• Press to activate shortcut function
Menu • Press to display available options
• Press to return to previous menu
Color Palette • Press to open Color Palette
• Choose from six dierent color modes
Zoom • Press to activate Zoom Slider
• Press to toggle between zoom levels
Radar Track • Press to open Radar Track settings
• Press to activate radar tracking function
Sensor Select • Press to toggle between Day and Thermal
camera (Not available for Ulysses Micro)
Power/Standby
• Press to open Power/Standby settings
• Select [Home] to return turret to preset home
position
• Select [Standby] to park and stow turret
• Press & hold to wake turret from parked
position
Accessing more information
For more information, please refer to the user manual that has been shipped with your camera or visit omnisense-systems.com to
download the latest user manual.
omnisense-systems.com
Singapore
8 Penjuru Lane,
Singapore 609189
T: [phone]
United States
1881 West State Road 84,
Bldg. 1 Unit 102, Fort Lauderdale,
Florida 33315, United States
T: [phone]