OmniSistem Spark 7 Zoom User manual
Tel: 253-395-9500 Fax: 253-395-9494
6403 South 208th Street, Kent, WA 98032
KEEPTHISMANUALFORFUTURENEEDS
1 of 25
Everypersoninvolvedwiththeinstallation,operationandmaintenanceofthisdeviceneedsto
● bequalified
● followtheinstructionsofthismanual
● considerthismanualtobepartofthetotalproduct
● keepthismanualfortheentireservicelifeoftheproduct
Passthismanualontoeveryfurtherowneroruseroftheproduct.
DownloadthelatestversionoftheusermanualfromtheOmniSistemwebsite.
Foryourownsafety,pleasereadthisusermanualcarefullybeforeyouinitiallystarttheproduct.
INTRODUCTION
Thank you for choosing an OmniSistem product. OmniSistem is a wholesaler of a large variety of lighting, sound,
truss, and effects. Since 1986, we have been providing quality and affordable lighting products to North America.
Weareconfidentthatourexcellentproductswillmeetyourexpectations.
Includedinthisboxyouwillfind:
1. Spark7Zoom
2. UserManual
3. OmegaHolderwithQuickLockFastener
4. PowerSupplyCable
5. SafetyCable
SAFETYINSTRUCTIONS
This device left our facility after a thorough QC check. In order to maintain excellent condition and to ensure a safe
operation, it is absolutely necessary for the user to follow the safety instructions and warnings detailed in this user
manual.
Important:
Damagescausedbythedisregardofthisusermanualarenotsubjecttowarranty.Thedealer
willnotacceptliabilityforanyresultingdefectsorproblems.
2 of 25
(SafetyInstructionsContinued)
● If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch
it on immediately. The arising condensation water might damage your device. Leave the device switched
offuntilithasreachedroomtemperature.
● Please make sure that there are no obvious transport damages. Should you notice any damages on the
A/C connection cable or on the casing, do not take the device into operation and immediately consult
yourlocaldealer.
● This device falls under Protection Class I. The power plug must only be plugged into a Protection Class I
outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or
poweroutletscanleadtothedestructionofthedeviceandmortalelectricalshock.
● Always plug in the power plug last. The power plug must always be inserted without excessive force.
Makesurethattheplugistightlyconnectedwiththeoutlet.
● Never let the power cord come into contact with other cables! Handle the power cord and all connections
with the mains with caution! Never touch them with wet hands, as this could lead to mortal electrical
shock.
● Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate
next to sources of heat or cold. Disregarding this can lead to power cord damages, fire or mortal electrical
shock.
● The cable insert or the female part in the device must never be strained. There must always be sufficient
cabletothedevice.Otherwise,thecablemaybedamagedwhichmayleadtomortaldamage.
● Make sure that the power cord is never crimped or damaged by sharp edges. Check the device and the
powercordfromtimetotime.
● If extension cords are used, make sure that the core diameter is sufficient for the required power
consumption of the device. All warnings concerning the power cords are also valid for possible extension
cords.
● Always disconnect from the power source, when the device is not in use or before cleaning it. Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord. Otherwise, the cable or
plug can be damaged leading to mortal electrical shock. If the power plug or the power switch is not
accessible,thedevicemustbedisconnectedviathemains.
● If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then
be cleaned with a dry cloth. Dust can reduce the insulation which may lead to electrical shock. More
severedirtinandatthedeviceshouldonlyberemovedbyaspecialist.
● There must never enter any liquid into power outlets, extension cords or any holes in the housing of the
device. If you believe even a minimal amount of liquid may have entered the device, it must immediately be
disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still
running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced
insulationcancausemortalelectricalshock.
● There must never be any objects entering into the device. This is especially valid for metal parts. If any
metal parts like staples or coarse metal chips enter into the device, the device must be taken out of
operation and disconnected immediately. Malfunction or shortcircuits caused by metal parts may cause
mortalinjuries.
Keep away children and amateurs! Never leave this device running unattended.
3 of 25
OPERATINGPROCEDURES
Thisdeviceisamovingheadlightforcreatingdecorativeeffects.Thisproductisonlyallowedtobeoperatedwith
analternatingvoltageof100240V,50/60Hzandwasdesignedforindooruseonly.
Thisdeviceisdesignedforprofessionaluse,e.g.onstages,inclubs,bars,theatres,etc.
Lightingeffectsarenotdesignedforpermanentoperation.Consistentoperationbreakswillensurethatthedevice
willserveyouforalongtimewithoutdefects.
Donotshakethedevice.Avoidbruteforcewheninstallingoroperatingthedevice.
Neverliftthefixturebyholdingitattheprojectorhead,asthemechanicsmaybedamaged.Alwaysholdthe
fixtureatthetransporthandles.
Whenchoosingtheinstallationspot,pleasemakesurethatthedeviceisnotexposedtoextremeheat,moisture
ordust.Thereshouldnotbeanycableslyingaround.Pleasemakesurethattheunitcannotbetouchedor
bumped.
Thisdevicemustneverbeoperatedorstockpiledinsurroundingswherewatersplash,rain,moistureorfogmay
harmthedevice.Moistureorveryhighhumiditycanreducetheinsulationandleadtomortalelectricalshocks.
Whenusingsmokemachines,makesurethatthedeviceisneverexposedtothedirectsmokejetandisinstalled
inadistanceof0.5metersbetweensmokemachineanddevice.Theroommustonlybesaturatedwithanamount
ofsmokethatthevisibilitywillalwaysbemorethan10meters.
Theambienttemperaturemustalwaysbebetween15°Cand+45°C.Keepawayfromdirectheat(particularlyin
cars)andheaters.
Therelativehumiditymustnotexceed50%withanambienttemperatureof45°C.This
devicemustonlybeoperatedinanaltitudebetween20and2000moversealevel.
Neverusethedeviceduringthunderstorms.Overvoltagecoulddestroythedevice.Alwaysdisconnectthedevice
duringthunderstorms.
Thissymboldeterminestheminimumdistancefromlightedobjects.Theminimumdistance
betweenlightoutputandtheilluminatedsurfacemustbemorethanthisvalue.
Thedevicemustonlybeinstalledonanonflammablesurface.Inordertosafeguardsufficientventilation,leave
50cmoffreespacearoundthedevice.
Thehousingmustnevertouchsurroundingsurfacesorobjects.
Makesurethattheareabelowtheinstallationplaceisclearwhenrigging,deriggingorservicingthefixture.
Foroverheaduse(mountingheight>100cm),alwaysfixthefixturewithanappropriatesafetycable.Fixthesafety
cableatthecorrectfixationpointsonly.Thesafetycablemustneverbefixedatthetransporthandles!
Onlyoperatethefixtureafterhavingcheckedthatthehousingisfirmlyclosedandallscrewsaretightlyfastened.
ThemaximumambienttemperatureTa=45°Cmustneverbeexceeded.
Operatethedeviceonlyafterhavingbecomefamiliarizedwithitsfunctions.Donotpermitoperationbypersonsnot
qualifiedforoperatingthedevice.Mostdamagesaretheresultofunprofessionaloperation!
Pleaseusetheoriginalpackagingifthedeviceistobetransported.
Pleaseconsiderthatunauthorizedmodificationsonthedeviceareforbiddenduetosafetyreasonsand
willvoidyourwarranty.
Neverremovetheserialbarcodefromthedeviceasthiswouldvoidthewarranty.
Ifthisdevicewillbeoperatedinanywaydifferenttotheonedescribedinthismanual,theproductmaysuffer
damagesandtheguaranteebecomesvoid.Furthermore,anyotheroperationmayleadtodangerslikeshort
circuit,burns,electricshock,crashing,etc.
4 of 25
PRODUCTFEATURES&SPECIFICATIONS
Light
● Lightsource:7xOSRAM15W4in1RGBWLEDs
● Lamplife:60,000hours
● LuminousFlux:3200lumen,6000lux@2.5m
● Control:Remoteon/offviaDMX
● Ballast:switchingmodepowersupply
● Beamangle:10°to60°
X/Y
● Pan:630°(2.5sec)or540°(2sec),Tilt:265°(1.8sec)
● 16bitresolution
● Autorepositioning
● 3phasemotorforfastandquietmovement
Features
● DMXchannels:15/24/14/16
● Fast,smooth,andsilentmovement
● RGBWColorMixing
● Zoom10°to60°
● Fullrange0100%dimmer
● Variousstrobe
● RDMfunctiontochangeDMXaddress,displayflip,X/YReverseandmore
● SoftwareupgradeviaDMX
● HibernationwhenlostDMXforpresettime
● Indicatetemperatureinfoofbase,armandlamp
● Fanspeedautochangeaccordingtotemperature
● Heatpipeforcooling
Display
● 2.4”LCDdisplaywithEnglish/Chinese/French/Spanishmenu
● Autolock
● Flip
● BackupcommunicatingIC
Power
● Maxpowerconsumption:115W
● Powersupply:Electronicautoranging
● Inputvoltagerange:100–240V,5060Hz
DimensionandWeight
● FixtureDimensions:244x179x322mm(9.6”x7”x12.7”)
● NetWeight:6kg(13.2lbs.)
5 of 25
OVERVIEW
(1) Head
(2) LED
(3) Arm
(4) Base
(5)Wirelessindicator
(6) Display
(7) Microphone
(8) Leftbutton
(9) Downbutton
(10) Enterbutton
(11) Upbutton
(12) Rightbutton
(13) Fuseholder
(14) Powerinput
(15) Powerswitch
(16) Poweroutput
(17) 3PINDMXinputsocket
(18) 3PINDMXoutputsocket
6 of 25
INSTALLATION
Rigging
The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1
hourwithoutanyharmingdeformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This
secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main
attachmentfails.
When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges, under
highworkingplacesandotherendangeredareasisforbidden.
The operator needs to make sure that safetyrelated and machine technical installations are approved by an expert
beforetakingintooperationforthefirsttimeandafterchangesbeforetakingintooperationanothertime.
The operator needs to make sure that safetyrelated and machine technical installations are approved by an expert
aftereveryfouryearsinthecourseofanacceptancetest.
The operator needs to make sure that safetyrelated and machine technical installations are approved by a skilled
persononceayear.
Procedure:
Theprojectorshouldbeinstalledoutsideareaswherepersonsmaywalkbyorbeseated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all installation
material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead use
aprofessionalstructuralrigger.Improperinstallationcanresultinbodilyinjuryand/ordamagetoproperty.
Theprojectorneedstobeinstalledoutofreachofpeople.
If the projector shall be lowered from the ceiling or high joists, professional trussing systems need to be used. The
projectormustneverbefixedswingingfreelyintheroom.
Caution: Projectors may cause severe injuries when crashing down! If you have doubts concerning the safety of a
possibleinstallation,doNOTinstalltheprojector!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector's
weight.
7 of 25
Theunitcanbeplaceddirectlyonthestagefloororriggedinanyorientationonatrusswithoutalteringits
operationcharacteristics(seethedrawing).
Thefixturebaseenablesmountingintwo
ways.
Foroverheaduse(mountingheight
>100cm),alwaysinstallanappropriate
safetybond.
Pleasenote:foroverheadriggingin
publicorindustrialareas,aseriesof
safetyinstructionsinthismanualneed
tobefollowed.Theoperatormustinform
themselvesonthecurrentsafety
instructionsandconsiderthem.
Themanufacturercannotbemadeliablefordamagescausedbyincorrectinstallationsorinsufficientsafety
precautions!
Installthesafetybondbyinsertingthequicklinkintheholeonthebottomofthebase.Pullthesafetybondover
thetrussingsystem.Inserttheendinthequicklinkandtightenthefixationscrew.
Themaximumdropdistancemustneverexceed20cm.
Asafetybondwhichalreadyholdsthestrainofafallorwhichisdefectivemustnotbeusedagain.
8 of 25
1. OmegaHolder
2. Clamp
3. SafetyCable
4. QuickLockFastener
ScrewtheclampviaaM12
screwandnutontotheOmega
holder.
Insertthequicklockfasteners
oftheOmegaholderintothe
respectiveholesonthebottom
ofthedevice.Tightenthe
quicklockfastenersfully
clockwise.
9 of 25
DMX512connection/connectionbetweenfixtures
Pleasenote,thestartingaddressdependsuponwhichcontrollerisbeingused.
OnlyuseaDMXcableand3pinXLRplugsandconnectorsinordertoconnectthecontrollerwiththefixtureor
onefixturewithanother.
OccupationoftheXLRconnection:
If you are using controllers during your show, you can connect the DMX output of the controller directly with the
DMX input of the first fixture in the DMX chain. If you wish to connect DMX controllers with other XLR outputs,
youneedtouseadaptercables.
BuildingaserialDMXchain:
Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture. Always
connectoneoutputwiththeinputofthenextfixtureuntilallfixturesareconnected.
Caution: At the last fixture, the DMX cable needs to be terminated. Plug the terminator with a 120Ωresistor
betweenSignal(–)andSignal(+)intheDMXoutputofthelastfixture.
10 of 25
ConnectionwiththeMains
Connectthedevicetothepowersourcewiththeenclosedpowersupplycable.
Theconfigurationoftheconnectioncablesisasfollows:
Cable
Pin
International
Brown
Live
L
Blue
Neutral
N
Yellow/Green
Ground
Groundneedstobeconnected!
Ifthedevicewillbedirectlyconnectedwiththelocalpowersupplynetwork,adisconnectionswitchwitha
minimumopeningof3mmateverypolehastobeincludedinthepermanentelectricalinstallation.
The device must only be connected with an electric installation carried out in compliance with the IEC standards.
The electric installation must be equipped with a Residual Current Device (RCD) with a maximum fault current of
30mA.
Devicemustnotbeconnectedtodimmingpacks.
The device is equipped with a lockable power input connector. Plug in the power cord and turn it to the right until it
locks.Plugthepowercordintoagroundedelectricaloutletthatmatchestheratedvoltageofthemachine.
OPERATION
Withthepowerswitch,youcanswitchthedeviceonandoff.
Afterbeingconnectedtothepowersupply,thefixturestartsrunning.Duringthereset,themotorsaretrimmedand
thedeviceisreadyforuse.
StandAloneoperation
IntheStandAlonemode,thedevicecanbeusedwithoutcontroller.
Disconnectthefixturefromthecontrollerandcalltheinternalprogram.
PleaserefertotheinstructionsunderControlBoard.
DMXControlledoperation
YoucancontroltheprojectorsindividuallyviayourDMXcontroller.EveryDMXchannelhasadifferentoccupation
withdifferentfeatures.TheindividualchannelsandtheirfeaturesarelistedunderDMXprotocol.
Addressing
TheControlBoardallowsyoutoassigntheDMXstartingaddress,whichisdefinedasthefirstchannelfromwhich
thefixturewillrespondtothecontroller.
If you set, for example, the address to channel 20, a fixture in 18 channel mode would use channels 20 to 38
forcontrol.
Pleasebesurethatyoudon’thaveanyoverlappingchannelsinordertocontroleachfixturecorrectlyand
independentlyfromanyotherfixtureontheDMXchain.Ifseveralfixturesareaddressedsimilarly,theywillworkin
sync.
PresstheUp/Downbuttonsforsettingthedesiredstartingaddress.Nowyoucanstartoperatingthefixturevia
yourlightingcontroller.
11 of 25
Note:
Afterswitchingon,thedevicewillautomaticallydetectwhetherDMX512dataisreceivedornot.Ifthere
isnodatareceivedattheDMXinput,thedisplaywillflash.
Thissituationcanoccurif:
● theXLRplug(cablewithDMXsignalfromcontroller)isnotconnectedwiththeinputofthedevice.
● thecontrollerisswitchedoffordefective,ifthecableorconnectorisdefectiveorthesignalwires
areswappedintheinputconnector.
Note:
It’snecessarytoinserttheXLRterminationplug(with120Ohm)inthelastlightinginthelinkinorderto
ensurepropertransmissionontheDMXdatalink.
DMXProtocol
St
Ex
8bit
16bit
Name
Function
DMX
1
1
1
1
Pan
Pan Coarse
0-255
2
2
Pan Fine
Pan Fine
0-255
2
3
2
3
Tilt
Tilt Coarse
0-255
4
4
Tilt Fine
Tilt Fine
0-255
3
5
3
5
Movement Speed
Fast to Slow
0-255
6
Movement
Function
Normal
Movement w/ Blackout
No Function
0-15
16-31
32-255
4
7
Shutter Function
Normal Shutter Functions
Pulse Effect Forward
Pulse Effect Reverse
Random Strobe
No Function
0-15
16-31
32-47
48-63
64-255
5
8
Shutter
Normal Shutter Functions:
Close
Strobe Rate (Slow to Fast)
Open
Pulse Effect Forward:
Close
Strobe Rate (Slow to Fast)
Open
Pulse Effect Reverse:
Close
Strobe Rate (Slow to Fast)
Open
Random Strobe:
Close
Strobe Rate (Slow to Fast)
Open
0-31
32-223
224-25
5
0-31
32-223
224-25
5
0-31
32-223
224-25
5
0-31
12 of 25
32-223
224-25
5
4
6
Shutter
Shutter Closed
No Function (Shutter Open)
Strobe Effect (Slow to Fast)
No Function (Shutter Open)
Pulse Effect in Sequences
No Function (Shutter Open)
Random Strobe Effect (Slow to Fast)
No Function (Shutter Open)
0-31
32-63
64-95
96-127
128-15
9
160-19
1
192-22
3
224-25
5
6
9
5
7
Dimmer
Dimmer (0-100%)
0-255
10
Dimmer Fine
Dimmer Fine Control
0-255
7
11
6
8
Virtual Color
Function
On Function
CTC Function
Forward Spin
Reverse Spin
Continuous
Color Bounce
No Function
0-15
16-31
32-47
48-63
64-79
80-111
112-25
5
8
12
7
9
Virtual Color 1
Color Temperature Correction 2000K-2700K
White 3200K
White 4200K
White 5600K
White 8000K
Forward Spin Rainbow Effect (Slow to Fast)
Reverse Spin Rainbow Effect (Slow to FasT)
Continuous & Color Bounce:
Blackout
Red
Green
Blue
White
Red=0, Green=Up, Blue=Full, White=0
Red=0, Green=Full, Blue=Down, White=0
Red=Up, Green=Full, Blue=0, White=0
Red=Full, Green=Down, Blue=0, White=0
Red=Full, Green=0, Blue=Up, White=0
Red=Down, Green=0, Blue=Full, White=0
Indexed Color:
Color 1 (Open)
Color 2 - Color 9
0-223
224-23
1
232-23
9
240-24
7
248-25
5
0-255
0-255
0-0
1-1
2-2
3-3
4-4
5-46
47-88
89-130
131-17
2
173-21
4
13 of 25
215-25
5
0-27
28-255
9
13
8
10
Virtual Color 2
(Only on Color
Bounce)
Color Bounce:
Blackout
Red
Green
Blue
White
Red=0, Green=Up, Blue=Full, White=0
Red=0, Green=Full, Blue=Down, White=0
Red=Up, Green=Full, Blue=0, White=0
Red=Full, Green=Down, Blue=0, White=0
Red=Full, Green=0, Blue=Up, White=0
Red=Down, Green=0, Blue=Full, White=0
0-0
1-1
2-2
3-3
4-4
5-46
47-88
89-130
131-17
2
173-21
4
215-25
5
10
14
9
11
Red
Red 0-100%
0-255
15
Red Fine
Red Fine Control
0-255
11
16
10
12
Green
Green 0-100%
0-255
17
Green Fine
Green Fine Control
0-255
12
18
11
13
Blue
Blue 0-100%
0-255
19
Blue Fine
Blue Fine Control
0-255
13
20
12
14
White
White 0-100%
0-255
21
White Fine
White Fine Control
0-255
14
22
13
15
Zoom
Zoom 10° to 60°
0-255
23
Zoom Fine
Zoom Fine Control
0-255
15
24
14
16
Control
Normal
Reset All
Reset Pan & Tilt
No Function
Reset Others
Display Off
Display On
No Function
Hibernate
No Function
0-7
8-15
16-23
24-47
48-55
56-63
64-71
72-87
88-95
96-255
ControlBoard
The Control Board offers several features. You can simply set the starting address, run the preprogrammed
14 of 25
program,orperformareset.
MainMenu
The main menu is accessed by pressing Enter until the display is lit. Browse through the menu by pressing the
arrow buttons (up, down, left, right). Press Enter in order to select the desired menu. You can change the
selection by pressing the arrow buttons. Press Enter in order to confirm selection, then exit back to the main
menutosavechanges.Thefunctionsprovidedaredescribedinthefollowingsections.
①=BasicReload②=ProgramReload③=PrivateReloadDefaultsettingsarelistedinbold.
MENU
SUBMENU
SELECTION
FUNCTION
Connect
DMXAddress①
XXX
DMXAddressSetting
Light
MaxTemperature①
80~139°C,120°C
176~282°F,248°F
Setinternal
temperaturetoshutthe
unitoff.(Activatesafter
5minutes.)
LampAdjust①
Pan…...
AdjustValue
Information
TimeInfo
CurrentXXXX(Hours)
FixtureLifeXXXX(Hours)
BootTime
TotalRunTime
Temperature
NearLampTemp
TemperatureSensors
FansSpeed
NearLampFan
FanSpeedSensors
ChannelValue
Pan…...
DisplayChannelValue
ErrorMessage
Pan,Tilt…...
ChannelErrors
FixtureModel
[Model&Brand]
DisplayModel&Brand
SoftwareVersion
1U01V.1.0.00
VersionofEachIC
Set
Reset
All
Pan&Tilt
Others
ResetAll
ResetPan&Tilt
ResetOthers
Movement
PanReverse①On/Off
PanReverse
15 of 25
TiltReverse①On/Off
PanDegree①630/540
Encoders①On/Off
Pan/TiltMode①Stand/Smooth
TiltReverse
ChoosePanDegree
EncoderWheelOn/Off
ChoosePan/TiltMode
UISet
MicSens.③0~99%,60%
NoSignal①Close/Hold/Auto/Music
TemperatureC/F①Fahrenheit/Celsius
FansMode①Auto/High
Hibernation①OFF,01M~99M,15M
Backlight①01~60M,02M
FlipDisplay①On/Off
DisplayBright③00~31,10
BrandShow①On/Off
KeyLock①On/Off
Language①En/简/繁/Fr/Sp
SensitivityofMic
ModeWhenNoSignal
TemperatureF°orC°
FanAutoorHigh
SleepTime
BacklightTime
ReverseDisplay180°
BrightnessSetting
ShowBranding
KeyLockOn/Off
LanguageSelect
Users(DMXChannel
Mode)
UserMode①
Standard
Extended
8bit
16bit
User
EditUser③
MaxChannel=XX
Pan=CH01
StandardDMXMode
ExtendedDMXMode
8bitMode
16bitMode
Usermode
EditUserMode
Calibration③
Password=XXX
Color=XXX
Password(050)
EditChannelValue
FixtureID③
Name
Password
PIDCode
Name
Password(050)
SetPIDofRDM
ReloadDefault
BasicReload(①)On/Off
ProgramReload(②)On/Off
PasswordXXX
PrivateReload(③)On/Off
AllReloadOn/Off
BasicReload
ProgramReload
Password(050)
PrivateReload
AllReload
Program
Play①
DMXReceive
SlaveReceiveSlaveReceive1,2,3
SequenceMaster/Standalone
MusicMusic/Standalone
DMXReceive
ChooseSlavePosition
RunSequence
MusicMode
SelectChase②
ChasePart1
Chase1~8Chase1
ChasePart2
Chase1~8Chase2
ChasePart3
Chase1~8Chase3
SelectandRunAuto
Program
EditChase②
Chase1ChaseTest
…Step01=SCXXX
Chase8Step64=SCXXX
Test
BeginningScene
EndingScene
EditScenes②
EditScene001Pan,Tilt…=XXX
~EditSceneFadeTime=XXX
250Scene=XXX
Time
DMXInput
InputManualScene
FadingTime
SceneTime
InputScenefrom
Controller
16 of 25
ScenesRecord
ScXX=>ScXX
AutoInputScenes
Connect
DMXAddressSetting
WiththisfunctionyoucanadjustthedesiredDMXaddressviatheControlBoard.
Select“DMXAddress“bypressingUporDown.
PresstheEnterbuttonthenadjusttheDMXaddressbypressingUporDown.
PresstheEnterbuttontoconfirm.
Light
MaxTemperature
With this function you can set the inside temperature at which the projector will automatically switch the lamp
off. Press Up or Down to select the maximum internal temperature between 80°C and 139°C. Internal
temperatures below 90°C are not critical. 90°C and more should lead to the lamp being switched off after five
minutes.Pleasenotethattheoutsidetemperatureshouldnotexceed45°C.
Information
CurrentTimeInformation
With this function you can display the temporary running time of the device from the last power on. The display
shows“XXXX”,“X“standsforthenumberofhours.Thecounterisresetafterturningthedeviceoff.
FixtureLife
With this function you can display the running time of the device. The display shows “XXXX”, “X“ stands for the
numberofhours.
TemperatureNearLampTemp
WiththisfunctionyoucandisplaythetemperatureintheprojectorheadindegreesCelsius/Fahrenheit.
Fanspeed
Withthisfunctionyoucandisplaythecurrentfanspeed.Thedisplayshows“XXXX”,“X“standsforHz.
Initialstatus
Withthisfunctionyoucandisplaywhichvaluetherespectivechannelswillstart.
Errorchannels
Withthisfunctionyoucandisplaythechannelerrors.
FixtureModel
Withthisfunctionyoucandisplaythemodelnumberandbrandofthefixture.
Softwareversion
WiththisfunctionyoucandisplaythesoftwareversionofeachIC.
1. Select“Softwarever.”bypressingUporDown.
2. PresstheEnterbutton.Thedisplayshowse.g.“1U01VX.X.XX”,“X.X.XX“standsfortheversionnumber.
Set
Reset
WiththisfunctionyoucanresetthedeviceviatheControlBoard.YoucanselectthedifferentResetfunctions
bypressingUporDown.
Movement
PANReverse
Withthisfunctionyoucanreversethepanmovement.
17 of 25
TILTReverse
Withthisfunctionyoucanreversethetiltmovement.
PANDegree
Withthisfunctionyoucanselectthepandegree.
1. Select“PANdegree”bypressingUporDown.
2. PresstheEnterbutton,thedisplayshows“540”.
3. PressUporDowntoselectthedesireddegreebetween“540”and“630”.
4. PresstheEnterbuttontoconfirm.
AutomaticPAN/TILTcalibration
Withthefunction"Encoders"youcancalibratethepan/tiltmovementtothecorrectstartingposition.
AdjustPAN/TILTspeed
Withthisfunctionyoucandefinethepan/tiltspeed.Youcanselectoneoftwodifferentmodes.
UISet
MicSensitivity
Withthisfunction,youcanselectthedesiredmicrophonesensitivitybetween0%and99%.
1. Select“MicSens”bypressingUporDown.
2. PresstheEnterbutton.
3. PressUporDowntoselectthedesiredsensitivity.
4. PresstheEnterbuttontoconfirm.
NoDMXStatus
Withthefunction"NoSignal",youcansetdifferentmodesifthereisnoDMXsignal.
1. Select"Close,Hold,AutoorMusic"bypressingUporDown.
2. PressUporDowntoselectbetween"Close","Hold","Auto"or"Music".
3. PresstheEnterbuttontoconfirm.
SelectTemperatureDesignation
Withthisfunctionyoucanselectthetemperaturedesignation.
1. Select“TemperatureC/F”bypressingUporDown.
2. PressUporDowntoselectthedesireddegreebetween“Celsius”and“Fahrenheit”.
3. PresstheEnterbuttontoconfirm.
HibernationPowerStandbyMode
With this function you can put the device in the power standby mode. This function will be automatically activated
after a predefined period of time of no DMX activity. In standby mode the lamp/LEDs and all motors will power
down if no DMX signal is sent to the fixture for a period of e. g. 15 minutes (can be user defined). The fixture will
automaticallyresetandreturntonormaloperationonceaDMXsignalissent.
Backlight
Withthisfunctionyoucanshutoffthedisplayafter2to60minutes.
FlipDisplay
Withthisfunctionyoucanflipthedisplayby180°forabetterviewwhenthefixtureisinstalledupsidedown.
Shortcut:Press“up”and“down”forthreesecondstoflipthedisplaydirectly.
BrandShow
With this function you can show or hide the brand name on the display during menu
operation,butstillshowitafterreset.
KeyLock
WiththisfunctionyoucanlockthekeysoftheControlBoardtoe.g.preventmenutampering.Ifthisfunctionis
18 of 25
activated,thekeyswillbeautomaticallylockedassoonasyouexitthemenu.Inordertodeactivateor
temporarilydeactivatethekeylockfunction,pressUPDOWNLEFTRIGHTENTERtoregainaccesstothe
menucommands.
Users
Usermode
Withthisfunctionyoucancreateuserdefinedchannelorders.
EditUser
Withthisfunctionyoucanadjustthepresetuserdefinedchannelorder.
Calibration
Withthisfunction,youcancalibrateandadjusttheeffectwheelstotheircorrectpositions.Thepasswordfor
thisfunctionis“050“.
FixtureID
RDM
WiththisfunctionyoucancallupvarioussubmenusviaRDM.
ThisdeviceisRDMready.RDMstandsfor"RemoteDeviceManagement"andmakesremotecontrolofdevices
connectedtotheDMXbuspossible.ANSIE1.202006byESTAspecifiestheRDMstandardasanextensionof
theDMX512protocol.
ManualsettingslikeadjustingtheDMXstartingaddressarenolongerneeded.Thisisespeciallyusefulwhenthe
deviceisinstalledinaremotearea.
RDMisintegratedinDMXwithoutinfluencingtheconnections.TheRDMdataistransmittedviathestandardXLR
poles1and2—newDMXcablesarenotnecessary.RDMreadyandconventionalDMXdevicescanbeoperated
inoneDMXline.TheRDMprotocolsendsitsownpackagesintheDMX512datafeedanddoesnotinfluence
conventionaldevices.
IfDMXsplittersareusedandRDMcontrolistobeused,thesesplittersmustsupportRDM.
ThenumberandtypeofRDMparametersdependonthe(optional)RDMcontrollerbeingused.
RDMParameterID's(Slot2122)
Value
Category_NetworkManagement
DISC_UNIQUE_BRANCH
0x0001
DISC_MUTE
0x0002
DISC_UN_MUTE
0x0003
CategoryRDMInformation
SUPPORTED_PARAMETERS
0x0050
PARAMETER_DESCRIPTION
0x0051
Category_ProductInformation
DEVICE_INFO
0x0060
19 of 25
DEVICE_MODEL_DESCRIPTION
0x0080
MANUFACTURER_LABEL
0x0081
DEVICE_LABEL
0x0082
FACTORY_DEFAULTS
0x0090
SOFTWARE_VERSION_LABEL
0x00C0
CategoryDMX512Setup
DMX_PERSONALITY
0x00E0
DMX_PERSONALITY_DESCRIPTION
0x00E1
DMX_START_ADDRESS
0x00F0
SLOT_INFO
0x0120
SLOT_DESCRIPTION
0x0121
Category_Sensors
SENSOR_DEFINITION
0x0200
SENSOR_VALUE
0x0201
Category_Power/LampSettings
0x04xx
DEVICE_HOURS
0x0400
CategoryDisplaySettings
DISPLAY_INVERT
0x0500
Category_Configuration
PAN_INVERT
0x0600
TILT_INVERT
0x0601
Category_Control
IDENTIFY_DEVICE
0x1000
RESET_DEVICE
0x1001
ReloadDefault
Withthisfunctionyoucanrestorethefactorysettingsofthedevice.Thedifferentsettings(markedinthetable)
willbesetbacktothedefaultvalues(shaded).
Program
PlaySlaveDevice
Withthisfunction,youcandefinethedeviceasaslave.YoucanchooseoneofthreedifferentSlaveprograms.
Forfurtherinformationsee“EditChase”.
Sequence
With this function, you can run the internal program. You can select the desired program under “Select Chase”.
You can set the number of steps under “Edit Chase”. You can edit the individual scenes under “Edit Scenes”.
With this function you can run the individual scenes either automatically, i.e. with the adjusted step time. The
20 of 25
Table of contents
Other OmniSistem Floodlight manuals
OmniSistem
OmniSistem Magic Box Wide Beam User manual
OmniSistem
OmniSistem Magic Box Wide Beam BR AL20 Series User manual
OmniSistem
OmniSistem Can Can User manual
OmniSistem
OmniSistem LED Dancer User manual
OmniSistem
OmniSistem Rocket Laser AL04 Series User manual
OmniSistem
OmniSistem LED Shot X4 User manual
OmniSistem
OmniSistem onyxpro 75 User manual
