Omron MicroHAWK V320-F User manual

84-9000400-02 Rev A
User Manual
MicroHAWK V320-F / V330-F / V420-F / V430-F
Barcode Reader

NOTE
•All rights reserved.
•No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any
form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the
prior written permission of OMRON.
•No patent liability is assumed with respect to the use of the information contained herein. Moreover,
because OMRON is constantly striving to improve its high-quality products, the information con-
tained in this manual is subject to change without notice. Every precaution has been taken in the
preparation of this manual. Nevertheless, OMRON assumes no responsibility for errors or omis-
sions.
Neither is any liability assumed for damages resulting from the use of the information contained in
this publication.
Trademarks
•Sysmac and SYSMAC are trademarks or registered trademarks of OMRON Corporation in Japan
and other countries for OMRON factory automation products.
•Microsoft, Windows, Windows Vista, Excel, and Visual Basic are either registered trademarks or
trademarks of Microsoft Corporation in the United States and other countries.
•ODVA, CIP, CompoNet, DeviceNet, and EtherNet/IP are trademarks of ODVA.
•QR Code is a registered trademark of DENSO WAVE INCORPORATED.
Other company names and product names in this document are the trademarks or registered trade-
marks of their respective companies.
Copyrights
Microsoft product screen shots reprinted with permission from Microsoft Corporation.

Terms and Conditions Agreement
Exclusive Warranty
Omron’s exclusive warranty is that the Products will be free from defects in materials and
workmanship for a period of twelve months from the date of sale by Omron (or such other period
expressed in writing by Omron). Omron disclaims all other warranties, express or implied.
Limitations
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF
THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based
on infringement by the Products or otherwise of any intellectual property right.
Buyer Remedy
Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally
shipped with Buyer responsible for labor charges for removal or replacement thereof) the
non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an
amount equal to the purchase price of the non-complying Product; provided that in no event shall
Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the
Products unless Omron’s analysis confirms that the Products were properly handled, stored,
installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before
shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from
the use of Products in combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any advice, recommendations or
information given orally or in writing, are not to be construed as an amendment or addition to the
above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS
IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on
which liability is asserted.
Warranty, Limitations of Liability
Warranties
Limitation on Liability; Etc
3
MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
Terms and Conditions Agreement

Suitability of Use
Omron Companies shall not be responsible for conformity with any standards, codes or regulations
which apply to the combination of the Product in the Buyer’s application or use of the Product. At
Buyer’s request, Omron will provide applicable third party certification documents identifying ratings
and limitations of use which apply to the Product. This information by itself is not sufficient for a
complete determination of the suitability of the Product in combination with the end product,
machine, system, or other application or use. Buyer shall be solely responsible for determining
appropriateness of the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR
PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A
WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON
PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products
Omron Companies shall not be responsible for the user’s programming of a programmable Product,
or any consequence thereof.
Performance Data
Data presented in Omron Company websites, catalogs and other materials is provided as a guide
for the user in determining suitability and does not constitute a warranty. It may represent the result
of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual
performance is subject to the Omron’s Warranty and Limitations of Liability.
Product specifications and accessories may be changed at any time based on improvements and
other reasons. It is our practice to change part numbers when published ratings or features are
changed, or when significant construction changes are made. However, some specifications of the
Product may be changed without any notice. When in doubt, special part numbers may be assigned
to fix or establish key specifications for your application. Please consult with your Omron’s
representative at any time to confirm actual specifications of purchased Product.
Information presented by Omron Companies has been checked and is believed to be accurate;
however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions.
Application Considerations
Disclaimers
Change in Specifications
Errors and Omissions
4MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
Terms and Conditions Agreement

Safety Precautions
Symbols and the meanings for safety precautions described in this manual.
In order for the product to be used safely, the following indications are used in this book to draw your
attention to the cautions. The cautions with the indications describe the important contents for
safety.
Meanings of Alert Symbols
Indicates a potentially hazardous situation which, if not avoided, will result in minor or moderate
injury, or may result in serious injury or death.
Additionally there may be significant property damage.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury or in property damage.
General Prohibition
Indicates general prohibitions, including warnings, for which there is no specific symbol.
General Caution
Indicates general cautions, including warnings, for which there is no specific symbol.
Electrical Hazard
Indicates the possible danger of electric shock under specific conditions.
High Temperature Caution
Indicates the possible danger of injury by high temperature under specific conditions.
WARNING
CAUTION
5
MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
Safety Precautions

Alert statements in this Manual
This product must be used according to this manual or Instruction sheet.
Failure to observe this may result in impairment of functions and performance of the product.
This product is not designed or rated for ensuring safety of persons. Do not use it for such purposes.
Never connect the AC power supply with this product.
When the AC power supply is connected, it causes the electric shock and a fire.
Since camera that can be connected with this product emits a visible light that may have an adverse
effect on the eyes, do not stare directly into the light emitted from the LED. If a specular object is
used, take care not to allow reflected light enter your eyes.
Please take external safety measures so that the system as a whole should be on the safe side even
if a failure of a this product or an error due to an external factor occurred. An abnormal operation may
result in serious accident.
Please take fail-safe measures on your side in preparation for an abnormal signal due to signal
conductor disconnection and/or momentary power interruption. An abnormal operation may result in
a serious accident.
Danger of burns. Do not touch the case while the reader is running or just after power is turned OFF,
since it remains extremely hot.
WARNING
CAUTION
6MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
Safety Precautions
When using equipment that is connected to an AC power source such as an AC adapter or PoE
injector, use it within the rated voltage range. Usage with a voltage higher than what it is rated for
may cause serious personal injury due to electric shock, or serious physical damage due to fire or
equipment failure. Do not touch any part of the device while in operation, or immediately after turning
OFF the power.

Precautions for Safe Use
• Please do not use this product to directly or indirectly use to detect the human body for the purpose
of ensuring the safety. In the same application, please use the safety sensor that is published on our
sensor catalog.
• Omron products are designed and manufactured as general-purpose products for use in general
industrial applications. They are not intended to be used in the following critical applications. If you
are using Omron products in the following applications, Omron shall not provide any warranty for
such Omron products, unless otherwise specifically agreed or unless the specific applications are
intended by Omron.
(a) Applications with stringent safety requirements, including but not limited to nuclear power control
equipment, combustion equipment, aerospace equipment, railway equipment, elevator/lift
equipment, amusement park equipment, medical equipment, safety devices and other applications
that could cause danger/harm to people’s body and life
(b) Applications that require high reliability, including but not limited to supply systems for gas, water
and electricity, etc., 24 hour continuous operating systems, financial settlement systems and other
applications that handle rights and property
(c) Applications under severe condition or in severe environment, including but not limited to outdoor
equipment, equipment exposed to chemical contamination, equipment exposed to electromagnetic
interference and equipment exposed to vibration and shocks
(d) Applications under conditions and environment not described in specifications
*1. In addition to the applications listed from (a) to (d) above, Omron products (see definition) are not intended for
use in vehicles designed human transport (including two wheel vehicles). Please do NOT use Omron
products for vehicles designed human transport. Please contact the Omron sales staff for information on our
automotive line of products.
*2. The above is part of the Terms and Conditions Agreement. Please use carefully read the contents of the
guarantee and disclaimers described in our latest version of the catalog, data sheets and manuals.
• Do not use the product in areas where flammable or explosive gases are present.
• Be careful when unpacking this product, please. Injury may occur if the reader falls and strikes a
person.
• Do not install the product close to high-voltage devices and power devices in order to secure the
safety of operation and maintenance.
• Make sure to tighten all installation screws securely.
Condition of the fitness of OMRON products
Installation Environment
7
MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
Precautions for Safe Use

Precautions for Safe Use
8MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
• Make sure to use the product with the power supply voltage specified by this manual.
•Do not connect AC power source to Sensor Controller. If connects AC power source, it might be a
cause of the failure.
•Use the wire of a suitable size (AWG 16 to 12) according to the current consumption.
•Use a DC power supply with safety measures against high-voltage spikes (safety extra low-voltage
circuits onthe secondary side).
•Keep the power supply wires as short as possible.
•Do the following confirmations again before turning on the power supply.
• Is the voltage and polarity of the power supply correct?
•Is not the load of theoutput signal short-circuited?
•Is the load current of the output signal appropriate?
•Is not the mistake found in wiring?
• Check wiring again before turning on the reader.
• Use only the cables designed specifically for the reader. Use of other products may result in
malfunction or damage of the reader.
• Always turn OFF the power of the reader and peripheral devices before connecting or disconnecting
a cable. Connecting the cable with power supplied may result in damage of the reader or peripheral
devices.
• Do not apply torsion stress to the cable. It may damage the cable.
• Secure the minimum bending radius of the cable. Otherwise the cable may be damaged.
• Do not attempt to dismantle, repair, or modify the product.
• Should you notice any abnormalities, immediately stop use, turn OFF the power supply, and contact
your OMRON representative.
• While the power is ON or immediately after the power is turned OFF, the case are still hot. Do not
touch the case.
• The reader must be used with the special mounting bracket (-AM0 or -AM1: sold separately), or the
reader may generate heat.
• When disposing of the product, treat it as an industrial waste.
• Do not drop the product nor apply excessive vibration or shock to the product. Doing so may cause
malfunction or burning.
• When controlling stages and robots using the read results (axis movement output based on
calibration and alignment measurement), always take fail-safe measures within the stage and robot
systems, such as checking whether the data obtained from the read results is within the range of
movement of the stages and robots.
Power Supply and Wiring
Ground
Other

Precautions for Correct Use
Install and store the product in a location that meets the following conditions:
• Surrounding temperature of 0 to +40°C (-50 to +75°C in storage)
• No rapid changes in temperature (place where dew does not form)
• Relative humidity of between 5 to 85%
• No presence of corrosive or flammable gases
• Place free of dust, salts and iron particles
• Place free of vibration and shock
• Place out of direct sunlight
• Place where it will not come into contact with water, oils or chemicals
• Place not affected by strong electro-magnetic waves
• Place not near to high-voltage, or high-power equipment
• For good heat dissipation, keep the distance.
• Do not install the product immediately above significant heat sources, such as heaters, transformers,
or large-capacity resistors.
• Do not let the ambient temperature exceed an operating temperature range.
• Provide a forced-air fan cooling or air conditioning if the ambient temperature is near the upper range
of operating temperature range so that the ambient temperature never exceeds the upper range of
operating temperature range.
• Do not install the product in a cabinet containing high-voltage equipment.
• Do not install the reader within 200 mm of power cables.
Installation and Storage Sites
Ambient Temperature
Noise Resistance
9
MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
Precautions for Correct Use

Precautions for Correct Use
10 MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
• Turning OFF the Power
When a message is displayed indicating that a task is in progress, do not turn OFF the power. Doing
so causes the data in the memory to be corrupted, resulting in the product not operating properly
upon the next start-up.
When turns OFF, conform the followings proceedings have completed. and then operate again.
• When saves using the reader:
Confirm the save processing is completed and next operation is possible.
• When saves using communication command:
Intended command is completed.
• Setting of Power Source
The power source need to be supplied from DC power source apparatus which is taken a save
ultra-low voltage circuit: to protect high voltage.
• Turn OFF the power and ensure the safety before maintenance.
• Clean the lens with a lens-cleaning cloth or air brush.
• Lightly wipe off dirt with a soft cloth.
• Do not use thinners or benzene.
• To ensure safe access for operation and maintenance, separate the reader as much as possible from
high-voltage equipment and power machinery.
• After confirming that this product is started up, communicate with the high-order device. When this
product has started up, an indefinite signal may be output from the high-order interface. To avoid this
problem, clear the receiving buffer of your device at initial operations.
• For symbols with a highly gloss surface, reading errors may occur because of regular reflection of the
LED light. If this occurs, provide a skew angle of 15° against the symbol.
• Do not look into the light emitted from the LED directly. When this products has started up, the LED
flashes.
• Under an environment with high humidity and rapid changes in temperature, the inside of the front
plate might fog up. When the read rates lower due to the fog, leave the device with turned it on for 30
minutes to 2 hours. Use it again after checking there is no fog on the front plate.
• This product is classified into the IEC 62471-1:2006 Risk-Exempt Group. However, this product does
emit a strong visible light that may have an adverse effect on the eyes. Do not stare directly into the
light emitted from the LED. If a specular object is used, take care not to allow reflected light to enter
your eyes.
Component Installation and Handling
Maintenance
Communication with High-Order Device
Other
LED Safety

Regulations and Standards
This regulation applies to MicroHAWK readers and peripheral devices.
If you export (or provide a non-resident with) this product or a part of this product that falls under the
category of goods (or technologies) specified by the Foreign Exchange and Foreign Trade Control Law
as those which require permission or approval for export, you must obtain permission or approval or
service transaction permission) pursuant to the law.
This regulation applies to reader and peripheral devices.
The reader is compliant with the standards below:
• EC Directive 2004/108/EC (Until April 19 2016) / EU Directive 2014/30/EU (After April 20 2016)
EN61326-1
Electromagnetic environment: Industrial electromagnetic environment (EN/IEC 61326-1 Table 2)
• This product complies with EC/EU Directives. EMC-related performance of the OMRON devices that
comply with EC/EU Directives will vary depending on the configuration, wiring, and other conditions
of the equipment or control panel on which the OMRON devices are installed.
• The customer must, therefore, perform the final check to confirm that devices and the overall
machine conform to EMC standards.
This regulation applies to reader and peripheral devices.
This product complies with UL Standards.
• UL60950-1 2nd-edition, 2014 (Class III)
Using Product Outside Japan
Conformance to EC/EU Directives
Conformance to UL Standards
11
MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
Guide for Users
This equipment has been evaluated for conformity in a commercial environment. When used in a residential
environment, it may cause radio interference.
Korean Radio Regulation (KC)
Regulations and Standards

Revision History
The manual’s part number and revision letter appear on the first and last pages.
Part Number 84-9000400-02 Rev A
Revision
12 MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
Revision code Date Revised content
ANovember 2019 First Publication.
Revision History

Table of Contents
Terms and Conditions Agreement ..........................................................................3
Safety Precautions ...................................................................................................5
Precautions for Safe Use.........................................................................................7
Precautions for Correct Use....................................................................................9
Regulations and Standards...................................................................................11
Revision History .....................................................................................................12
Section 1 Overview
1-1 Introduction............................................................................................................................... 1-2
1-2 Splash Screen........................................................................................................................... 1-3
1-3 Navigation Bar .......................................................................................................................... 1-4
1-4 Flash Icon.................................................................................................................................. 1-5
1-5 Help Icon ................................................................................................................................... 1-6
1-6 Application Settings Icon......................................................................................................... 1-7
1-7 Left Panel .................................................................................................................................. 1-8
1-8 Right Panel.............................................................................................................................. 1-10
1-9 Image Area .............................................................................................................................. 1-11
1-10 Guided Tour .......................................................................................................................... 1-16
Section 2 Quick Start
2-1 Introduction .............................................................................................................................. 2-2
2-2 MicroHAWK and WebLink Quick Start.................................................................................... 2-2
Section 3 Start
3-1 Overview.................................................................................................................................... 3-2
3-2 Assisted Setup.......................................................................................................................... 3-4
3-3 Reader Information................................................................................................................... 3-5
3-4 Setup Buttons ........................................................................................................................... 3-6
Section 4 Setup
4-1 Cycle .......................................................................................................................................... 4-2
4-2 Acquire ...................................................................................................................................... 4-4
4-3 Decode....................................................................................................................................... 4-7
4-4 Match String.............................................................................................................................. 4-9
13
MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
CONTENTS

4-5 Format Output......................................................................................................................... 4-13
4-6 Outputs.................................................................................................................................... 4-17
4-7 Configuration Database ......................................................................................................... 4-19
4-8 Favorites.................................................................................................................................. 4-25
Section 5 Run
5-1 Counts ....................................................................................................................................... 5-2
5-2 Rate............................................................................................................................................ 5-3
5-3 Read Time ................................................................................................................................. 5-4
5-4 Output Data ............................................................................................................................... 5-5
5-5 Image History............................................................................................................................ 5-6
Section 6 Application Settings
6-1 Application Settings Menu....................................................................................................... 6-2
6-2 Save ........................................................................................................................................... 6-3
6-3 New ............................................................................................................................................ 6-4
6-4 Load ........................................................................................................................................... 6-5
6-5 Advanced .................................................................................................................................. 6-6
6-6 Language................................................................................................................................... 6-7
6-7 Terminal..................................................................................................................................... 6-8
6-8 Beeper ....................................................................................................................................... 6-9
6-9 Guided Tour ............................................................................................................................ 6-10
6-10 Image Storage....................................................................................................................... 6-11
6-11 Restore Default Settings ...................................................................................................... 6-18
6-12 Activate Account Management ........................................................................................... 6-19
6-13 Enable USB Drive Mode....................................................................................................... 6-27
6-14 About WebLink ..................................................................................................................... 6-28
Section 7 Terminal
7-1 Send........................................................................................................................................... 7-2
7-2 Find ............................................................................................................................................ 7-3
7-3 Filters......................................................................................................................................... 7-4
Section 8 Advanced Settings
8-1 Introduction............................................................................................................................... 8-2
8-2 Camera Setup ........................................................................................................................... 8-3
8-3 Communications ...................................................................................................................... 8-4
8-4 Read Cycle ................................................................................................................................ 8-5
8-5 Symbologies ............................................................................................................................. 8-6
14 MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
CONTENTS

8-6 I/O............................................................................................................................................... 8-8
8-7 Symbol Quality ....................................................................................................................... 8-25
8-8 Match String............................................................................................................................ 8-26
8-9 Diagnostics ............................................................................................................................. 8-27
8-10 Image Storage....................................................................................................................... 8-28
8-11 Configuration Database ....................................................................................................... 8-29
8-12 Differences from Default...................................................................................................... 8-30
Appendices
Appendix A General Specifications ..............................................................................................A-1
Appendix B Electrical Specifications ...........................................................................................B-1
Appendix C Serial Commands ......................................................................................................C-1
Appendix D Communications........................................................................................................D-1
Appendix E Calibration ..................................................................................................................E-1
Appendix F Read Cycle.................................................................................................................. F-1
Appendix G Symbologies ............................................................................................................. G-1
Appendix H I/O Parameters ...........................................................................................................H-1
Appendix I Symbol Quality ............................................................................................................. I-1
Appendix J Matchcode................................................................................................................... J-1
Appendix K Camera and IP Setup.................................................................................................K-1
Appendix L Configuration Database............................................................................................. L-1
Appendix M Utilities ...................................................................................................................... M-1
Appendix N Output Format............................................................................................................N-1
Appendix O Communications Protocol....................................................................................... O-1
Appendix P ASCII Table .................................................................................................................P-1
Appendix Q Glossary of Terms ....................................................................................................Q-1
Appendix R Q & A...........................................................................................................................R-1
15
MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
CONTENTS

1-1
MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
1
This section provides a general overview of the WebLink user interface.
1-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1-2 Splash Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-3 Navigation Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1-4 Flash Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1-5 Help Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1-6 Application Settings Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1-7 Left Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1-8 Right Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
1-9 Image Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1-10 Guided Tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
Overview

1 Overview
1-2 MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
1-1 Introduction
The browser-based WebLink interface enables quick and easy configuration and testing of
MicroHAWK V320-F, V330-F, V420-F, V430-F readers without the need to install or access files on a
host system.
WebLink is reliable, lightweight, and operating-system-independent without compromising the power
and depth of its tool set.
WebLink offers novice users an intuitive way to connect, configure, monitor, and troubleshoot a
MicroHAWK reader, and provides the power and flexibility expected by advanced users.

1-3
1 Overview
MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
1-2 Splash Screen
1
1-2 Splash Screen
After you open a browser and enter your reader's IP address , the first thing you will see is the splash
screen
, a portion of which is shown below. You will also see a progress bar as your WebLink session starts.

1 Overview
1-4 MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
1-3 Navigation Bar
The navigation bar at the top of the WebLink interface features buttons for three primary views: Start,
Setup, and Run.

1-5
1 Overview
MicroHAWK V320-F / V330-F / V420-F / V430-F Barcode Reader User Manual
1-4 Flash Icon
1
1-4-1 Save to Flash Memory
1-4 Flash Icon
The flash icon allows you to save current settings to the reader for reboot. When the current reader
settings match those saved in flash memory, the disk icon changes from red to blue.
1-4-1 Save to Flash Memory
1-4-2 Saved to Flash Memory