On Point Audio OPA-10 ACTIVE User manual

On Point Audio, Inc.
OPA-10 ACTIVE USER MANUAL
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operation and maintenance instructions.
The lightening flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of un-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The On Point Audio OPA-10 Active was designed to provide very high performance,
high-quality sound reinforcement as well as very high output-to-size ratio. The OPA-10
Active was designed for use in portable and fixed installation indoor environments such
as night clubs, houses of worship, meeting halls and general live performance
applications. The OPA-10 Active features a compact yet incredibly rugged enclosure
design that provides very high acoustic output with excellent sight line characteristics,
portability and ease of use.

Specifications
Frequency Response: 65 Hz – 20,000 Hz
Coverage Pattern: 90o H X 40o V – fully rotatable
Input/Thru Connections: 3 Pin XLR-type
(Pin 2 +)
Power:
Peak - Total System: 2,000 Watts
Continuous- Total System: 1,000 Watts
Peak Low Frequency: 1,000 Watts
Peak High Frequency: 1,000 Watts
Continuous Low Frequency: 500 Watts
Continuous High Frequency: 500 Watts
AC Mains Power: Autoswitching 115 V AC or 230 V AC
(104VAC – 253VAC)
(50 Hz – 60 Hz)
Input to achieve rated output 1.5 V RMS
Max Acoustic Output (Peak) 131 dB*
Rigging M10 Stainless Steel (10 Points)
Supplied Accessories AC Mains Cables 2 each
(3 Pin USA and Euro)
Dimensions (H X W X D): 564.5 X 290 X 370 mm
22.2 X 11.4 X 14.57 inches
Weight (kg / lb): 22.2 kg / 49 lbs
Operating temperature (C/F) 0C-43C / 32F- 110F
* NOTE: Maximum Acoustic Output is based on smoothed system response, not peak
driver response.

370.0 [14.57]
290.0 [11.42]
564.5 [22.23]
290.0 [11.42]
249.8 [9.83]
Read all of the instructions included in this manual
Copies of this manual should be retained by the system’s installer AND end-user.
This manual must be read and understood and ALL warnings must be followed.
Follow all instructions to insure optimal product performance.
The OPA 10-Active is a convection-cooled device and requires at least 6 inches (152
mm) of clearance behind the enclosure to allow the heat sink to adequately cool the
internal electronics.
DO NOT INSTALL NEAR ANY HEAT SOURCES!
Use ONLY the supplied AC Mains connector.
Protect the AC Mains power cord from being walked on or otherwise damaged and
inspect for damaged connections and damaged insulation.

The OPA-10 ACTIVE may be suspended. DO NOT SUSPEND ANY ITEMS OR OTHER
ENCLOSURES BELOW THE OPA 10 ACTIVE.
DO NOT SUBSTITUTE SUSPENSION HARDWARE.
SUSPENSION SHOULD BE ATTEMPTED BY A PROFESSIONAL THAT IS FAMILIAR
WITH LOCAL AND NATIONAL CODES AND SAFE SUSPENSION PRACTICES!
There are NO user serviceable parts inside the enclosure. DO NOT REMOVE THE
AMPLIFIER MODULE! (See Service section for details OR contact On Point Audio)
FCC STATEMENT
The OPA 10 Active has been tested and is compliant with the limits for Class B digital
devices, per Part 15 of the FCC rules. Test data is available from On Point Audio.
INTRODUCTION
Thank you for purchasing the On Point Audio OPA-10 Active and for your support of our
products. The OPA-10 Active will provide you with many years of high performance with
proper use and care. Please read this manual completely and become familiar with the
design and operation of this advanced active speaker system.
CONTENTS
The OPA-10 Active system is shipped in one carton. The contents of the carton are as
follows:
OPA-10 Active System
This system includes one OPA-10 Active loudspeaker including a bi-amplified Class-D
digital power amplifier system with onboard Digital Signal Processing (DSP) and two
each AC Mains cables.
RECOMMENDED ACCESSORIES
Although not supplied with the OPA-10 ACTIVE System, On Point Audio recommends
using the OPA-10 Active system with a high-quality loudspeaker stand when used in
portable applications. On Point Audio also recommends the OPA-Sub Active when
additional low-frequency output and response is required. The OPA-Sub Active also
includes a 35 mm / 1.375 inch diameter mounting pole that allows the OPA10 Active to
be safely elevated above the OPA-Sub Active.

The OPA Sub Active pole is NON-adjustable. DO NOT substitute poles. Make sure that
the OPA Sub Active is placed on a level surface.
OTHER ACCESSORIES
On Point Audio offers an external U-Bracket for use with OPA-10 Active enclosures.
This U-Bracket is the OPA-10-U.
On Point Audio also offers the Eye Bolt Kit that contains 4 x 304-grade stainless steel,
forged-shoulder eyebolts for suspending the OPA-10 Active.
FEATURES AND APPLICATIONS
The OPA-10 Active is a professional product and is designed to be used with a high-
quality mixing console. The OPA-10 Active does not provide any additional, user-
selectable, equalization or gain. Equalization and gain functions should be provided by
the mixing console. This design enables gain stages to be limited, thus reducing system
noise as well as substantially reducing the possibility of gain stage overloads.

On Point Audio does not feel that adding additional EQ and gain functions are
necessary or appropriate for truly professional products. The addition of redundant
functions such as EQ and gain are usually the cause of clipping, distortion and greatly-
reduced system performance and output. Any venue-specific equalization needs are
best provided by high-quality outboard devices or high-performance EQ sections found
on professional quality mixing consoles.
The OPA-10 Active features an onboard digital signal processor (DSP) that performs
analog to digital conversion, equalization, high-order crossover, delay and system
dynamics processing. The system’s dynamics processing consists of a
compressor/limiter function designed to provide ultra-fast threshold system protection
and maximized system dynamics.
SETUP AND USE OF THE OPA-10 ACTIVE
AC MAINS CONNECTION
Prior to connecting the AC mains cable, please insure that the AC mains switch on the
OPA-10 Active is in the OFF position.
On/Off Switch
The OPA-10 Active will operate on AC mains voltages of 115 volts to 230 volts. (The
OPA-10 Active uses an internal “autoswitch” circuit) The required AC mains frequency
is between 50 Hz and 60 Hz. The operating voltage is between 104VAC and 253VAC
The OPA-10 Active uses a standard IEC-type AC mains connector system. To mate the
AC mains cable with the AC mains connector on the amplifier, simply align the plug with
the panel’s connector and press the AC mains cable into place. Always support the
OPA 10 Active’s enclosure with one hand while performing this operation. The AC

mains connector is shown below. It is located on the lower portion of the OPA-10
Active’s input panel.
NOTE: The OPA-10 Active is supplied with two AC Mains cables. Select the cable with
the proper termination for the country specific mating receptacle!
AC Mains panel connector
To disconnect the cable end from the AC mains connector, pull back on the molded
plug at the end of the cable, not on the cable itself.
NOTE: ALWAYS turn off the AC mains power BEFORE attempting to disconnect the
AC mains cable from the OPA 10 Active amplifier module!
DO NOT CONNECT THE AC MAINS END OF THE AC MAINS CABLE IN AN AREA
THAT IS WET OR SUBJECT TO CONDENSATION OR DAMP CONDITIONS!
Once the AC mains cable is securely connected to both the amplifier and AC mains
supply, the OPA-10 Active enclosure may be turned on. It is good practice is to make
sure the audio levels on the mixer output (or other source output) are reduced or muted
prior to applying power to the OPA-10 Active.
NOTE: When power is applied to the OPA-10 Active and the unit is turned on, there is
approximately a 5 to 15 second delay before the pilot light illuminates.

Pilot Light
NOTE: If the pilot light does not illuminate within 30 seconds, the unit may be in a
FAULT CONDITION. If this occurs, the system should be returned to On Point Audio for
evaluation.
THERE ARE NO USER-SERVICABLE PARTS INSIDE. DO NOT REMOVE THE
AMPLIFIER MODULE!
AUDIO CONNECTIONS
The OPA-10 Active includes both male and female XLR-type connectors. Any standard
XLR-type cable end connectors may be used.
The image below illustrates the top portion of the OPA 10 Active input plate. Both the
audio input and audio thru connectors are shown.

Input Thru
An audio input level of 1.5 V RMS will drive the OPA 10 Active amplifier to full power.
The OPA-10 Active’s input section also allows for “paralleling” multiple OPA-10 Active
or other powered systems. This function is achieved by using the output/thru XLR-type
connector located next to the input XLR-type connector on the OPA-10 Active’s
amplifier module.
RIGGING AND SUSPENSION OF THE OPA-10 Active
The OPA-10 Active features 10 x M10 (metric) stainless steel rigging points. These
rigging points enable the system to be suspended for temporary or permanent
installations. There are three M10 points on the top of the enclosure, three on the
bottom of the enclosure and two on each side.
The M10 rigging points are shown in the image below.
Rigging Points shown above

The OPA-10 Active may also be mounted to any high-quality loudspeaker stand with a
standard 1.375 inch (35 mm) diameter mounting pole. The mounting pole MUST be
located on a level surface that is capable of safely supporting the weight of both the
loudspeaker stand and the OPA-10 Active.
DO NOT ADD OR SUSPEND ANY OTHER ITEMS FROM THE OPA-10 Active OR ITS
LOUDSPEAKER STAND
WARNING
DO NOT ATTEMPT TO SUSPEND ON POINT AUDIO PRODUCTS WITHOUT
UNDERSTANDING LOCAL AND NATIONAL CODES THAT APPLY TO OVERHEAD
SUSPENSION OF PRODUCTS.
DO NOT ATTEMPT TO SUSPEND ON POINT AUDIO PRODUCTS UNLESS YOU
ARE A PROFESSIONAL WITH KNOWLEDGE OF LOCAL AND NATIONAL CODES
RELATED TO SAFE SUSPENSION AND ARE EXPERIENCED IN SUSPENDING
PRODUCTS OVERHEAD.
ON POINT AUDIO IS NOT RESPONSIBLE FOR FAILURES RELATED TO NON-
COMPLIANCE WITH LOCAL AND NATIONAL CODES AND SAFE SUSPENSION
PRACTICE.
DO NOT ATTEMPT TO SUSPEND THIS PRODUCT WITHOUT READING AND
UNDERSTANDING THE DOCUMENT “Suspension of On Point Audio Products”. THIS
DOCUMENT MAY BE FOUND AT: www.onpointaudio.com.
ALL ASSOCIATED RIGGING IS THE RESPONSIBILITY OF OTHERS.
ROTATING THE HF HORN
The OPA-10 Active’s HF horn has a coverage pattern of 90o Horizontal X 40o Vertical
which is preferred when the speaker is positioned vertically. The horn/driver assembly
can be rotated to deliver 40o X 90o when the speaker is positioned horizontally or for
other applications.
To rotate the horn assembly, first remove all the screws on each side of the grille and
remove the grille from the system. Then remove the screws around the perimeter of the
horn. After doing this, the horn can be easily rotated in either direction thanks to its
square shape. It is not necessary to disconnect the connections to the compression
driver when rotating the horn.