One Control Tire Linc User manual

w
CCD-0004068
Quick Start Guide
Alert Indicator
Powered by
Technology

NOTE: The purpose of this Quick Start Guide is for a
quick setup of the Alert Indicator for the Tyre Pressure and
Temperature Monitoring System. Refer to the complete
Aftermarket Manual https://support.lci1.com/tire-linc for
additional information.
Quick Start Guide
Pairing Alert Indicator to Repeater......................... 3
Operation ................................................................... 6
2

Pairing Alert Indicator to Repeater
1. Pair the Alert Indicator (Fig.1)
to the Repeater by pressing and
releasing the Alert Indicator button
(Fig.1A).
A. The Indicator will power up and
its LED (Fig.1B) will blink red once
then blue three times indicating the
Alert Indicator is NOT linked to the
repeater.
NOTE: After 10 seconds, the Indicator
will enter sleep mode.
2. Link the Alert Indicator to the
Repeater by pressing and holding
the Pair Mode button (Fig.2A) on the
Repeater for at least ve seconds until
the Status LED blinks rapidly.
A
B
Fig.1
Fig.2
A
3

III. After the Indicator beeps three
times, release the button. The LED
will blink green three times.
B. The Alert Indicator’s LED will
briefly blink blue and emit a happy
tone, indicating it has been linked to
the Repeater.
6. The Alert Indicator is now linked to
the Repeater.
NOTE: The Repeater’s Status LED
will indicate green, yellow or red to
indicate certain conditions (see Step
7). The number of blinks of the LED,
regardless of color, also indicates
battery status (see Step 8).
3. Release the Repeater’s Pair Mode
button.
4. Press the Alert Indicator’s button
(Fig.1A) once to make sure the
indicator is awake.
5. Within 10 seconds of waking the
indicator, press and hold the Alert
Indicator button.
A. Continue to hold the Alert
Indicator button until its LED and
buzzer sounds.
I. One beep will sound off and one
green LED flash will be emitted.
Continue to hold the button.
II. Two beeps will sound off and
the LED will blink green twice.
Continue to hold the button.
4

7. Wait for the Repeater’s Status LED
to turn o󰀨, then press and release
the Alert Indicator’s button. The
indicator’s LED will ash as follows:
• Green to indicate the Repeater
is in range and monitoring; tyres
within pressure and temperature
limits.
• Yellow if there is no connection
or out of range of the Repeater;
cannot detect tyre status.
• Red to indicate a fault, either
high/low pressure or temperature is
out of range; Indicator will beep for
10 seconds when tyre issue is seen
for the rst time. LED will continue
to blink red until fault is corrected.
• Red followed by blue notes In-
dicator is not linked to the Repeater.
8. Battery status indicators are as
follows (regardless of LED color in
Step 7):
• 3 blinks - Good, full charge
• 2 blinks - Low, not full charge
• 1 blink - Critical, needs charging
5

When Stem Sensors are under
pressure, data is transmitted to the
Repeater when tyres are:
• moving/rotating, every one
minute;
• not moving/not rotating, every 15
minutes.
The Alert Indicator will continually
scan for tyre events from the Repeat-
er when it is plugged into a USB cable
connected to a powered USB port.
This conguration is best because
it will be the most responsive to tyre
events.
When not plugged into a powered
USB port, e.g., running on internal
battery, the Alert Indicator periodically
scans for data sent to the Repeater,
when tyres are:
• moving/rotating, every one
minute;
• not moving/not rotating, scan-
ning time increments in 1, 2, 4,
8 and 15 minutes (maximum),
with the Indicator entering sleep
between scans.
The Alert Indicator is provided to send
simple audio and visual alerts of a
tyre pressure or temperature event.
No additional programming of the
Indicator is required.
NOTE: The Repeater’s Status
LED will blink green, yellow or
red to indicate certain conditions.
The number of blinks of the LED,
regardless of color, also indicates
battery status.
Operation
6

Wait for the Repeater’s Status LED
to turn o󰀨, then press and release the
Alert Indicator’s button. The indica-
tor’s LED will ash as follows:
• Green to indicate the Repeater
is in range and monitoring; tyres
within pressure and temperature
limits.
• Yellow if there is no connection
or out of range of the Repeater;
cannot detect tyre status.
• Red to indicate a fault, either
high/low pressure or temperature is
out of range; Indicator will beep for
10 seconds when tyre issue is seen
for the rst time. LED will continue
to blink red until fault is corrected.
Deep Sleep Mode
To place the Alert Indicator into deep
sleep mode, hold the button until
hearing one beep and then release it.
The Alert Indicator will emit a happy
tone and shut o󰀨.
NOTE: The Alert Indicator can only
enter deep sleep if not plugged in.
• Red followed by blue notes Indi-
cator is not linked to the Repeater.
Battery status indicators are as fol-
lows (regardless of LED color):
• 3 blinks - Good, full charge
• 2 blinks - Low, not full charge
• 1 blink - Critical, needs charging
7

CCD-0004068
Rev: 11.02.20
Should you have any questions, please do not
hesitate to contact us at 574-537-8900 or by email
at [email protected]. Self-help tips, techni-
cal documents, product videos and a training class
schedule are available at lci1.com or by download-
ing the MyLCI app.
Contact
Lippert Components Incorporated