ONE PRO H-C04 User manual

USER
MANUAL
VERSION 2.0
PRODUCT: CO2 JET MACHINE
MODEL: H-C04

1USER MANUAL (H-C04)
DISCLAIMER
1.FORWARD
Congratulations! Thanks for purchase from us.
This manual contains all information required for the intended use of the
equipment. Deviation from the described intended use can result in a
hazardous situation and/or property damage.
This manual includes notes and warnings on safe operation of the equipment.
2.LIABILITY
Accepts no liability for claims from third parties arising from unauthorised use,
use other than that stated in this manual, and use other than in accordance
with the General Conditions registered at the Chamber of Commerce.
Refer further to the General Conditions. These are available on request, free of
charge.
Although considerable care has been taken to ensure a correct and suitably
comprehensive description of all relevant components, the manual may
nonetheless contain errors and inaccuracies.
Should you detect any errors or inaccuracies in the manual, we would
be grateful if you would inform us. This helps us to further improve our
documentation.
WARNING
Read this manual carefully before installing and/or using
this product. Failure to read the manual and to follow the
printed instructions may lead to personal injury and/or
damage to the product.

AMAZING BOOSTER FOR STAGE
2
Use Manual Hose CO2 Bottle
3.INTRODUCTION
3.1 DESCRIPTION AND APPLICATION OF THE CO2 JET
The CO2 Jet is intended to electronically blow white smoke plumes of CO2
from a distance. As soon as the CO2 leaves the cylinder through the CO2
Jet’s secured high-pressure hoses, it converts into gas. This formation of gas is
accompanied by a strong hissing sound aend a solid white plume of smoke will
be visible. The length of this plume is on average 8 metres. This depends on
the air humidity: in case of a high degree of air humidity, the smoke plume will
be larger and in case of a low degree of air humidity it will be smaller.
3.2 NECESSARY ACCESSORIES
The following parts belong to the CO2 Jet

3USER MANUAL (H-C04)
Product Name Moving Head CO2 JET
Voltage 100-120V60HZ200-240V50HZ
Power 150W
Spraying distance 8-10 meters
Maximum pressure 1400Psi
Head shaking angle 180 degrees
Product size 36cmx25.3cmx28.3cm
Packing size: 44.5cmx33cmx32.5cm
Net weight/Gross weight; 10.7 kg/14.6 kg
Control mode: DMX512 control, line control self-pro-
pelled point spray, line control self-pro-
pelled long spray
4.Product parameters:
Function introduction
5 channels:
1-channel shaking head
2-channel jet
3 channels automatic back and forth point spray
4-channel positioning point spraying (point spraying at the
position where the head of 1 channel is moving)
5-channel speed adjustment (from fast to slow)

AMAZING BOOSTER FOR STAGE
4
5.SAFELY
The CO2 Jet has been designed and constructed in such a manner that it can
be used safely. This applies to the use, the circumstances and the regulations
as described in this documentation. Reading this documentation and following
the instructions are therefore necessary for everyone who is authorised to
work with the CO2 Jet. The CO2 Jet must be placed and used in surroundings
that preferably:
•Have a relative humidity degree of no more than 75%.
•Are reasonably free of dust, corrosive gases and high concentrations of
organic vapours.
•Are not situated in the vicinity of a source of vibration.
6.GENERAL SAFETY RULES
Key function description
OK——Menu/OK
UP---digital plus
DOWN-number reduction
RETURN--return
Product features
1. Independent research and development design appearance
2. This machine adopts self-developed LCD color screen motherboard
3. The machine does not need to be xed and does not bounce when it is
placed on the ground at any angle
4. With electronic control point spray function
5. With electronically controlled long spray function

5USER MANUAL (H-C04)
•Only use the CO2 Jet if there are no people, animals or other objects
in the direction of the output within the output distance. The shooting directi-
on is the direction in which the output pipe on the CO2 Jet is pointed. The
output distance depends on the humidity in the air.
•Make sure that children, unauthorised people and animals do not obtain
access to the CO2 Jet.
•Safety devices may not be removed or disabled.
•All required safety devices must be in good condition and function properly.
•Ensure sufcient lighting of the surroundings.
•Keep the workplace clean.
•Only authorised persons may carry out work with the CO2 Jet.
7.PREPARATIONS
Unpack the CO2 Jet. Dispose of the packaging material without harming
the environment. Inspect the machine for any damage. If damage is noticed
this must be reported to us.
8.INSTALLS ILLUSTRATION
• Place the CO2 Jet on a solid and even surface,Always make sure that
there are no people within 3 metres of the CO2 Jet.
• In order to test it, you rst need to check if the gas valve on the CO2
bottle is still in a closed position. Now you can check if the has been installed
properly by switching the electricity on and off.if the system has been
connected properly you will hear a clicking sound which is produced by the
opening and closing of the magnetic valve in the CO2 Jet.
• Connect the high pressure CO2 hoses to the CO2 bottles.Firmly secure
the couplings by hand.Place the CO2 bottles (liquid CO2 with dip pipe) on an
even and solid surface.Place the bottles in such a position that the valve

AMAZING BOOSTER FOR STAGE
6
9.OPERATION METHOD
To operate the CO2 Jet you press the switch on and off. As soon as you
press the switch the magnetic valve will immediately open and a white
smoke plume will exit from the CO2 Jet. When you press the switch again to
the off position the valve will immediately close.
To operate the machine you can use the DMX controller. This machine have
1 channel . It can be sprayed by any value (0--255).
10.SWITCHING OFF
• Close the valves of the gas bottles.
•Activate the CO2 Jet one more time to remove the remaining pressure
from the hose.
• Disconnect the plug(s) of the CO2 Jet from the power supply
•Only when there is no more gas in the hose it can be disconnected from
the gas bottle and the CO2 Jet.
• opening does not point in the direction of persons or objects.
• Connect the hose to the CO2 Jet and let it click into place so it is rmly
secure.
• When the system is properly connected you can open the valves of the
CO2 bottles. Check for leaks.
• When the gas hoses are not properly connected gas can escape. If this is
the case then turn the couplings tighter until gas is no longer escaping. The
CO2 Jet is now ready for use .
CO2 Blasts cannot exceed 10 seconds in length for each
blast; two blasts cannot occur within 5 seconds of each
other, Power must be connected last as to ensure safety.
NOTICE

7USER MANUAL (H-C04)
11.PRECAUTIONS FOR OPERATION
Using a damaged or an improper installed machine
can lead to death, serious injury or property damage. Always
inspect the machine thoroughly before oper-ation.
The CO2 jet may only be installed by adults and au-thorised
persons. The CO2 jet may only be operated if all parts are
completely and correctly installed/con-nected.
The machine can be damaged, if you do not follow these
procedures carefully.
WARNING
WARNING
CAUTION
12.MAINTENANCE
To achieve the maximum service life of the CO2 jet you must regularly clean
the CO2 jet and test if it is working correctly. Should the CO2 jet not work for
some reason then please contact us.
Do not replace parts yourself; always consult us if necessary.
DANGER
13.MALFUNCTION OBVIATES
•The CO2 Jet is leaking
Check if the coupling of the gas hose is connected properly to the coupling of
the CO2 Jet. If it is not entirely secured then press it rmly. This‘s only possible

AMAZING BOOSTER FOR STAGE
8
14.CORRECT DISPOSAL
This symbol on the product and / or accompanying docu-
ments means that used electrical and electronic products
(WEEE) should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take
this product to designated collection points where it will be
accepted free of charge
Alternatively, in some countries you may be able to return your products to your
when there is no pressure on the hose.If the problem persists, then consult the
technical service of us.
•Only a small smoke plume is visible when the CO2 gas exits the
CO2 Jet.
Visibility can vary due to air humidity. The output will be more visible when
there is high absolute air humidity.
•There is no white smoke plume visible when the CO2 gas exits the
CO2 Jet.
You may not have the right carbon dioxide cylinders. Connect cylinders with
liquid carbon dioxide and a dip pipe to the CO2 Jet. In some cases the dip pipe
may be broken. In that case replace the carbon dioxide cylinder with another
and inform your gas supplier about the cylinder with the defective dip pipe.
•The CO2 Jet is still malfunctioning after troubleshooting
Always contact your dealer or the technical service of our company rst in
case of uncertainties,questions about the CO2 Jet works or other issues with
regard to the CO2 Jet.

9USER MANUAL (H-C04)
local retailer upon purchase of an equivalent new product.
Disposing of this product correctly will help save valuable resources and prevent
any potential negative effects on human health and the environment, which
could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest designat-
ed collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance
with your national legislation.
15.AFTER-SALE SERVICE
The warranty time is one year since the date of purchase, you may get help
and solve way through our technical support at any time,and we could offer
free parts necessary to repair products. One of the following conditions not
covered under warranty:
1- Because the consume ruse,maintenance,transportation, damage caused
by improper storage;
2- Non designated personnel to repair the damage caused by the
disassembly of products;
3- Because of damage caused by force majeure Abnormal voltage, such as
fire, earthquake, tsunami, debris flow;
4- More than the warranty period.
* if found quality problems please contact sales center or after sale service,
do not disassemble, due to quality problems caused by self-disassembly or
accident,the company will not bear any responsibility.