Onkyo HT-RC440(B) User manual

HT-RC440
RC-834M
AV RECEIVER
Black model
MODEL HT-RC440(B)
Ref. No. 4395
072012
120V AC, 60HzB MDC

HT-RC440
SERVICE PROCEDURE-1
Clear
Stand-by
CBL/SAT
ON/STANDBY
1. Replacing the fuses
2. Safety check out
(U.S.A. model only)
After correcting the original service problem, perform the following safety check before releasing the unit to the customer.
Leakage current Check
Measure the leakage current to a known earth ground (water pipe or conduct etc.) by connecting a leakage current
tester between the earth ground and exposed metal parts of the unit (input/output ground terminals, screw heads or metal overlays etc.).
Plug the power supply cord directly into a 120Vac 60Hz wall socket and turn ON/STANDBY button on.
Any current measured must not exceed 0.5mA.
3. To initialize the unit
1. Press ON/STANDBY button while pressing down CBL/SAT button when the unit is POWER ON, then the FL displays
"CLEAR", and turn to STAND-BY.
Preset memory and each mode stored in the memory, are initialized and will return to the factory settings.
2. Remove power cord from wall outlet.
This symbol located near the fuse indicates that the
fuse used is slow operating type, For continued protection against
fire hazard, replace with same type fuse, For fuse rating, refer to
the marking adjacent to the symbol.
Ce symbole indique que le fusible utilise est e lent.
Pour une protection permanente, n'utiliser que des fusibles de meme
type. Ce demier est indique la qu le present symbol est apposre.
F6401
F6401 or
F6402
F6402 or
F9002
F9002 or
F201
F9001
10A-UL/T-233
10A-T/UL-ST2
10A-UL/T-233
10A-T/UL-ST2
8A-UL/T-233
8A-T/UL-ST2
4A-SEUL-TL250V
1A-SEUL-TL250V
252330GR
252333GR
252330GR
252333GR
252329GR
252261GR
252392T
252397T
!
!
!
!
!
!
!
!
FUSE
FUSE
FUSE
FUSE
FUSE
FUSE
FUSE
FUSE
REF NO. PART NAME DESCRIPTION PART NO. REMARKS

HT-RC440
SERVICE PROCEDURE-2
M1.09/12612ALN
M1.09/12612ALN
D1.05/12605AEA
O1.00/11Z19AL
(TONE)
(TONE)
(TONE)
(TONE)
(TONE)
(TONE) (TONE)
(TONE)
ON/STANDBY DISPLAY
4. To check version of each Firmware
1. Press ON/STANDBY (Power On)
2. Press DISPLAY + ON/STANDBY.
3. Press (Tone) ---> Forward
Press (Tone) ---> Reversed.
4. Press ON/STANDBY (Power Off).
Main Microprocessor
DSP
HDMI/Video Microprocessor
Version displayed
only for 3 seconds.
Version of Main Microprocessor displayed
only for 3 seconds.
e.g.
e.g.
e.g.
e.g.

HT-RC440
SERVICE PROCEDURE-3
Resistor
Top
5. Notes on repairs (Power supply board)
Some parts on BAPS-1120 may remain high voltages
even after the power cord is disconnected from AC power source.
Before starting repair and any other work , please discharge C9002 by connecting resistors between its terminals. See the figure below
(recommended resistor spec: 5 k ohms/ 10W)
It is dangerous to touch the "HIGH VOLTAGE PRIMARY" area surrounded by white lines without discharging.
U0080
POWER SUPPLY(PRI) PC BOARD ASS'Y
BAPS-1120

TX-NR414/ 515/ 515AE/ 616/ 616AE/ HT-R758/791/ HT-RC440/460/470
DEBUG MODE-1
AUDIO DEBUG MODE-1/6
To set in Debug mode
1. Press and hold down DISPLAY button, then press ON/STANDBY button.
2. Press +(TONE) button while the version number of microprocessor is displayed.
3. Press DISPLAY button while the version number of DSP is displayed.
4. Press DISPLAY button.
5. Press DISPLAY button.
6. Press DISPLAY button.
7. Press DISPLAY button.
8. Press DISPLAY button.
9. Press DISPLAY button.
10. Press DISPLAY button.
11. Press DISPLAY button.
D1.05/12327AEA
M1.06/12417AE
AUDIO dubug mode
The status of DSP and DIR etc
will be displayed.
0A0002:__:00__
e.g.
The version number of microprocessor is displayed
only for 3 seconds.
ON/STANDBY DISPLAY
+ (TONE)
The version number of DSP is displayed
only for 3 seconds.
The operations of DSP and DIR etc are able to checked by the information displayed on FL in this debug mode.
This information will help to analysing digital audio no sound trouble.
DSP dubug mode
STEP-1
DSP dubug mode
STEP-5
Exit
DSP dubug mode
STEP-8
DSP dubug mode
STEP-4
DSP dubug mode
STEP-3
DSP dubug mode
STEP-2
DSP dubug mode
STEP-7
DSP dubug mode
STEP-6
e.g.
e.g.
e.g.
e.g.
e.g.
e.g.
e.g.
e.g.
ANA:o:NON:C:__
1:ANA_048k048k
2/0.0:_2.0:3/4
2:o:PCM_:PCM__
_00:x:F:OFF___
SP00F_00F00409
_48_48256STB__
TX-NR414/515/515AE
HT-R758/791
HT-RC440/460
TX-NR616/616AE
HT-RC470
ON/STANDBY + (TONE) DISPLAY

TX-NR414/ 515/ 515AE/ 616/ 616AE/ HT-R758/791/ HT-RC440/460/470
DEBUG MODE-2
AUDIO DEBUG MODE-2/6
Contents of Display
1 2 3 45blank
114 1312106 87432 5 9 11
4.Muting port
5.Factor of muting
1.st_srd.lmd 2.st_srd.extdec
3.st_srd.extdecmd
STEP-1
FL Display
D
A
: DIGMUTE port
: AMUTE port
bit_1
bit_2
bit_3
bit_4
bit_5
bit_6
bit_7
bit_8
: SELMUTE
: POWMUTE
: PROTECTMUTE
: AUDIOOUTMUTE
: AUDIOMUTE
: DIRMUTE
: DACMUTE
: HDMIMUTE
Display area
C_LM_LAST
C_LM_PURE
C_LM_DIRECT
C_LM_STEREO
C_LM_MONO
C_LM_SURR
C_LM_THX_MUSIC
C_LM_THX_GAME
C_LM_THX_CINEMA
C_LM_THX_U2GAME
C_LM_THX_U2MUSIC
C_LM_THX_U2CINEMA
C_LM_AUDYSSEY
C_LM_DTSSS
C_LM_ORCHESTRA
C_LM_UNPLUGGED
C_LM_STUDIOMIX
C_LM_TVLOGIC
C_LM_ALLCHST
C_LM_FULLMONO
C_LM_TD
C_LM_TESTTONE
C_LM_TESTTHR
C_LM_TESTAUTO
C_LM_ASC
C_LM_FLASH
C_LM_DEBUGMODE
C_LM_FLASH2
C_LM_FLASH3
C_LM_FLASH4
C_LM_FLASH_CHECK
C_LM_RPG
C_LM_ACTION
C_LM_ROCKBAND
C_LM_SPORTS
01
02
03
04
05
20
50
70
90
A0
A8
B0
D0
48
06
07
08
09
0A
0B
0C
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
0D
0E
0F
10
C_EXTDEC_OFF
C_EXTDEC_20_PLII
C_EXTDEC_20_PLIIX
C_EXTDEC_20_PLIIZ
C_EXTDEC_20_NEO6
C_EXTDEC_51_MTR
C_EXTDEC_51_DSC
C_EXTDEC_51_NEO6
C_EXTDEC_51_EX
C_EXTDEC_51_PLIIX
C_EXTDEC_51_PLIIZ
C_EXTDEC_9624
C_EXTDEC_9624_MTR
C_EXTDEC_71MULTI
C_EXTDEC_20_NEURAL
C_EXTDEC_51_NEURAL
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0E
0F
10
C_EXTDECMD_OFF
C_EXTDECMD_10
C_EXTDECMD_20
C_EXTDECMD_MOVIE
C_EXTDECMD_MUSIC
C_EXTDECMD_GAME
C_EXTDECMD_HEIGHT
C_EXTDECMD_WIDE
00
01
02
03
04
05
06
07
e.g. 0A0002:__:00__

TX-NR414/ 515/ 515AE/ 616/ 616AE/ HT-R758/791/ HT-RC440/460/470
DEBUG MODE-3
AUDIO DEBUG MODE-3/6
STEP-3
11 13
114 1312106 87432 5 9 11
11.Source_format
12
12.st_srd.fs 13.st_hd_display.fs
???
008
011
012
016
022
024
032
044
048
064
088
096
176
192
: unknown
: 8kHz
: 11kHz
: 12kHz
: 16kHz
: 22kHz
: 24kHz
: 32kHz
: 44.1kHz
: 48kHz
: 64Hz
: 88.2kHz
: 96kHz
: 176.4kHz
: 192kHz
???
008
011
012
016
022
024
032
044
048
064
088
096
176
192
: unknown
: 8kHz
: 11kHz
: 12kHz
: 16kHz
: 22kHz
: 24kHz
: 32kHz
: 44.1kHz
: 48kHz
: 64Hz
: 88.2kHz
: 96kHz
: 176.4kHz
: 192kHz
UNLK
ANA
PCM
AC3
DTS
MPEG
DATA
UNKW
NORD
NPCM
FS96
: DDR_UNLOCK
: DDR_ANALOG
: DDR_PCM
: DDR_AC3
: DDR_DTS
: DDR_MPEG
: DDR_DATA
: DDR_UNKNOWN
: DDR_NOT_READY
: DDR_NOT_PCM
: DDR_FS96
NODT
DTSC
AAC
MPCM
MCH
TRUE
MSTR
DSD
PLUS
EXPR
DTSH
: DDR_NOT_DETECT
: DDR_DTSCD
: DDR_AAC
: DDR_MCHPCM
: DDR_MCH
: DDR_TRUE
: DDR_MSTR
: DDR_DSD
: DDR_DDPLUS
: DDR_DTSEXP
: DDR_DTSHD
114 1312106 87432 5 9 11
blank
8 1096
7.DSP decode
8.HDMI audio lock
10.RX mute
9.Display inhibit frag
6.Audio input channel
7
STEP-2
ANA
COX
OPT
HDM
ARC
: Analog
: Coaxial
: Optical
: HDMI
: ARC
o
×
: DSP Detect OK
: DSP No Detect
STB
TRS
NON
: SOUND STATE FIX
: SOUND STATE UNFIX
: SOUND STATE NONE
S
C
: display_inhibit SET
: display_inhibit CLR
V : HDMI MUTE
e.g. ANA:o:NON:C:__
e.g. 1:ANA_048k048k

TX-NR414/ 515/ 515AE/ 616/ 616AE/ HT-R758/791/ HT-RC440/460/470
DEBUG MODE-4
AUDIO DEBUG MODE-4/6
STEP-5
18 19
114 1312106 87432 5 9 11
18. Audio output OK/NG
20
19.Details of input format 20.Details of the format for the FL display
blank
o
x
: decode OK
: decode NG
ANA
PCM
DLB
DEX
DTS
MTR
DSC
D96
96M
AAC
MCH
DSP
MPCM
DSD
TRUE
TREX
MSTR
PLUS
PLEX
EXP
DTSH
DSUR
DPSR
TRSR
: C_SRC_ANA
: C_SRC_PCM
: C_SRC_DD
: C_SRC_DD_EX
: C_SRC_DTS
: C_SRC_DTS_MTR
: C_SRC_DTS_DSC
: C_SRC_DTS_96
: C_SRC_DTS_96M
: C_SRC_AAC
: C_SRC_MCH
: C_SRC_DSP
: C_SRC_MCHPCM
: C_SRC_DSD
: C_SRC_TRUE
: C_SRC_TRUE_EX
: C_SRC_MSTR
: C_SRC_DDPLUS
: C_SRC_DDPLUS_EX
: C_SRC_DTSEXP
: C_SRC_DTSHD
: C_SRC_DD_SUR
: C_SRC_DDPLUS_SUR
: C_SRC_TRUE_SUR
ANA
PCM
DLB
DEX
DTS
MTR
DSC
D96
96M
AAC
MCH
DSP
MPCM
DSD
TRUE
TREX
MSTR
PLUS
PLEX
EXP
DTSH
DSUR
DPSR
TRSR
: C_SRC_ANA
: C_SRC_PCM
: C_SRC_DD
: C_SRC_DD_EX
: C_SRC_DTS
: C_SRC_DTS_MTR
: C_SRC_DTS_DSC
: C_SRC_DTS_96
: C_SRC_DTS_96M
: C_SRC_AAC
: C_SRC_MCH
: C_SRC_DSP
: C_SRC_MCHPCM
: C_SRC_DSD
: C_SRC_TRUE
: C_SRC_TRUE_EX
: C_SRC_MSTR
: C_SRC_DDPLUS
: C_SRC_DDPLUS_EX
: C_SRC_DTSEXP
: C_SRC_DTSHD
: C_SRC_DD_SUR
: C_SRC_DDPLUS_SUR
: C_SRC_TRUE_SUR
114 1312106 87432 5 9 11
:16
14
15.Information of the LFE channel input
17.Number of channels after decoding
16.Channel information for the FL display
14.Information of the input channels
for listening mode transition
15
STEP-4
17
0
1
2
: SW 0ch
: SW 1ch
: SW 2ch
four-digit string "10.2" "5.1" "1 +1"
???
10
20
30
21
31
22
32
23
33
24
34
: C_FMT_UNKNOWN
: C_FMT_10
: C_FMT_20
: C_FMT_30
: C_FMT_21
: C_FMT_31
: C_FMT_22
: C_FMT_32
: C_FMT_23
: C_FMT_33
: C_FMT_24
: C_FMT_34
4H2
5H2
4W2
5W2
4H4
4H3
5H4
5H3
4W4
4W3
5W4
5W3
11
: C_FMT_42H
: C_FMT_52H
: C_FMT_42W
: C_FMT_52W
: C_FMT_44H
: C_FMT_43H
: C_FMT_54H
: C_FMT_53H
: C_FMT_44W
: C_FMT_43W
: C_FMT_54W
: C_FMT_53W
: C_FMT_11
???
10
20
30
21
31
22
32
23
33
24
34
: C_FMT_UNKNOWN
: C_FMT_10
: C_FMT_20
: C_FMT_30
: C_FMT_21
: C_FMT_31
: C_FMT_22
: C_FMT_32
: C_FMT_23
: C_FMT_33
: C_FMT_24
: C_FMT_34
4H2
5H2
4W2
5W2
4H4
4H3
5H4
5H3
4W4
4W3
5W4
5W3
11
: C_FMT_42H
: C_FMT_52H
: C_FMT_42W
: C_FMT_52W
: C_FMT_44H
: C_FMT_43H
: C_FMT_54H
: C_FMT_53H
: C_FMT_44W
: C_FMT_43W
: C_FMT_54W
: C_FMT_53W
: C_FMT_11
e.g. 2/0.0:_2.0:3/4
e.g. 2:o:PCM_:PCM__

TX-NR414/ 515/ 515AE/ 616/ 616AE/ HT-R758/791/ HT-RC440/460/470
DEBUG MODE-5
AUDIO DEBUG MODE-5/6
STEP-7
2826
114 1312106 87432 5 9 11
26. AudioIF DA830 input
3027 31 3229
27. Information of DIR Burst Preamble
28. DIR Free or Busy
30. DIR sequence number
SEQ_DIG_POWEROFF
SEQ_DIG_RESET
SEQ_DIG_POWERON_WAIT
SEQ_DIG_RESTART
SEQ_DIG_WAIT_HDMI_FREE
SEQ_DIG_INPSEL_SET
SEQ_DIG_ANALOG_SET
SEQ_DIG_DIGITAL_SET
SEQ_DIG_MCHPCM_SET
SEQ_DIG_MCHANA_SET
SEQ_DIG_DDPDTSHD_SET
SEQ_DIG_NET_SET
SEQ_DIG_INIT_ERROR
SEQ_DIG_CHK_ERROR1
SEQ_DIG_CHK_ERROR2
SEQ_DIG_CHK_FREE
SEQ_DIG_CHK_ANALOG
SEQ_DIG_LOCK_PLL
SEQ_DIG_LOCK_ANA
SEQ_DIG_FREE
SEQ_DIG_FREE_ANA
00
10
11
12
13
20
30
31
32
33
34
35
40
41
42
43
50
60
61
f0
f1
/* POWER OFF*/
/* DIR RESET*/
/* POWER ON Waiting*/
/* DIGITAL RESTART */
/* HDMI(Waiting for final)*/
/* DIGITAL INPUT Setting */
/* DIR ANALOG Input setting*/
/* DIR DIGITAL Input setting*/
/* DIR MCHPCM Input setting*/
/* DIR MCHANA Input setting*/
/* DIR DD+ DTS-HD HR Input setting*/
/* DIR NET Input setting*/
/* DIR INIT ERROR*/
/* DIR CHECK ERROR1*/
/* DIR CHECK ERROR2*/
/* DIGITAL CHECK FREE*/
/* CHECK ANALOG MODE */
/* 2nd PLL LOCK*/
/* ANALOG 2nd PLL LOCK*/
/* DIGITAL FREE*/
/* ANALOG Fix*/
32. DAC sequence number
31. DIR switch sequence number
29. DIR Detect Fs
CLOCK_FREQ_UNKNOWN
CLOCK_FREQ_8K
CLOCK_FREQ_11K
CLOCK_FREQ_12K
CLOCK_FREQ_16K
CLOCK_FREQ_22K
CLOCK_FREQ_24K
CLOCK_FREQ_32K
CLOCK_FREQ_44K
CLOCK_FREQ_48K
CLOCK_FREQ_64K
CLOCK_FREQ_88K
CLOCK_FREQ_96K
CLOCK_FREQ_128K
CLOCK_FREQ_176K
CLOCK_FREQ_192K
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
SEQ_SWITCH_POWEROFF
SEQ_SWITCH_RESET
SEQ_SWITCH_POWERON_WAIT
SEQ_SWITCH_CHANGE
SEQ_SWITCH_FREE
00
01
02
03
04
/* POWER OFF */
/* RESET */
/* POWER ON WAIT */
/* CHANGE */
/* FREE */
SEQ_DAC_POWEROFF
SEQ_DAC_RESET
SEQ_DAC_POWERON_WAIT
SEQ_DAC_INITIALIZE
SEQ_DAC_RESTART
SEQ_DAC_CMND_SET
SEQ_DAC_FREE_WAIT
SEQ_DAC_FREE
00
01
02
03
04
05
06
07
/* POWER OFF */
/* RESET */
/* POWERON WAIT */
/* INITIALIZE */
/* RESTART */
/* COMMAND SET */
/* FREE WAIT */
/* FREE */
IH
DS
IS
NT
SP
AD
HR
: AUD_IF_I2S_H
: AUD_IF_DSD
: AUD_IF_I2S
: AUD_IF_NET
: AUD_IF_SPDIF
: AUD_IF_ADC
: AUD_IF_DDDTSHR
DS
DP
Preamble Val
: DTSHD HR
: DD PLUS
: 0x??
F
B
: Free
: Busy
114 1312106 87432 5 9 11
23
21.Dialog norm
22.Return value of DIRINT Request_dir
(DDC_STATUS)
22
STEP-6
21
25.HDDVD/BLUE(only DDPLUS)
24.emphasis of information
23.Return value of DIR busy or free
Request_dir (DDC_BUSY)
blank 24 25
blank
Dialog Norm value from 0 to 31
o
x: LOCK
: UNLOCK
F
B
: Free
: Busy
: Free
: Busy
F
B
BD
HD
: Bluray
: HDDVD
e.g. _00:x:F:OFF___
e.g. SP00F_00F00409

TX-NR414/ 515/ 515AE/ 616/ 616AE/ HT-R758/791/ HT-RC440/460/470
DEBUG MODE-6
AUDIO DEBUG MODE-6/6
STEP-8
33
114 1312106 87432 5 9 11
33. Information of the input FS of DA830
blank
34 35 36
35. Information of the input MCLK of DA830
36. State of the audio input of DA830
34. Information of the output FS of DA830
64
128
256
384
512
640
768
: AUD_MCLK_64Fs
: AUD_MCLK_128Fs
: AUD_MCLK_256Fs
: AUD_MCLK_384Fs
: AUD_MCLK_512Fs
: AUD_MCLK_640Fs
: AUD_MCLK_768Fs
NO
TRS
STB
: AUD_STS_SOUND_NO
: AUD_STS_SOUND_TRANS
: AUD_STS_SOUND_STAB
UNK
8
11
12
16
22
24
32
44
48
64
88
96
176
192
: C_FS_UNKNOWN
: C_FS_08
: C_FS_11
: C_FS_12
: C_FS_16
: C_FS_22
: C_FS_24
: C_FS_32
: C_FS_44
: C_FS_48
: C_FS_64
: C_FS_88
: C_FS_96
: C_FS_176
: C_FS_192
UNK
8
11
12
16
22
24
32
44
48
64
88
96
176
192
: C_FS_UNKNOWN
: C_FS_08
: C_FS_11
: C_FS_12
: C_FS_16
: C_FS_22
: C_FS_24
: C_FS_32
: C_FS_44
: C_FS_48
: C_FS_64
: C_FS_88
: C_FS_96
: C_FS_176
: C_FS_192
e.g. _48_48256STB__